Unconfigured Ad Widget

Collapse

Problem with Uzi

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • E Pluribus Unum
    Calguns Addict
    • Dec 2006
    • 8098

    Problem with Uzi

    Hello all;

    I am in the process of building up an Uzi.

    I bailed my receiver out of 10-day jail at PRK yesterday, and I am in the process of building up the gun.

    I have a parts kit from a Norinco 320.


    Remember, an Uzi is different than a normal fire arm. There is no traditional hammer that strikes a firing pin. In an uzi, the hammer/firing pin is all one piece called the "striking assembly".



    I have an issue where every time I put the gun together... I:


    Cycle the bolt, firing pin engages and stops, bolt goes forward, pull the trigger, Striking assembly clicks.

    I let go of the trigger, cycle the action, firing pin engages and stops, bolt goes forward,pull the trigger, the Striking assembly clicks.

    I let go of the trigger, cycle the action, Striking assembly engages and stops, bolt goes forward, pull the trigger, NOTHING.

    After this point, the striking assembly never comes forward until I remove the lower from the upper.

    Another thing it does:

    If at any point, I hold the trigger down, as would be the case under normal firing conditions, the striking assembly never engages to the rear; it always follows the bolt closed. It really is a single-shot pistol because it only shoots one round, and then the action must be manually cycled again, after the trigger is released, in order for it to fire another round.

    Here is a short video I made of the problem:

    Originally posted by Alan Gura
    The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
    Originally posted by hoffmang
    12050[CCW] licenses will be shall issue soon.

    -Gene
    sigpic
  • #2
    redcliff
    Calguns Addict
    • Feb 2008
    • 5676

    Tough one to diagnose with comparing the fit to a working one. Since your receiver is aftermarket I'm wonderring if the pistol grip is sitting too low and the sear is coming up too high.

    Edit: I took a look at my r.a.w. Uzi mdl B, with the bolt and striker removed but the receiver attached to the trigger housing I can pull the trigger over and over and the sear/sear lever resets each time in the trigger housing without any action of the bolt/striker. Does yours reset with the bolt/striker removed?

    You may want to post your video at the Uzitalk forums, they have some pretty knowledgeable people there.
    Last edited by redcliff; 01-12-2011, 4:28 PM.
    "You keep using that word. I do not think it means what you think it means."
    "What we get away with isn't usually the same as what's good for us"
    "An extended slide stop is the second most useless part you can put on a 1911"

    "While Ruger DA revolvers may be built like a tank, they have the aesthetics of one also,
    although I suppose there are a few tanks which I owe an apology to for that remark"

    Comment

    • #3
      E Pluribus Unum
      Calguns Addict
      • Dec 2006
      • 8098

      Originally posted by redcliff
      Tough one to diagnose with comparing the fit to a working one. Since your receiver is aftermarket I'm wonderring if the pistol grip is sitting too low and the sear isn't being reset properly by the striker or the sear is coming up too high.

      I seriously doubt that is the issue. This is a NoDakSpuds receiver, and they are considered some of the best, and I paid to have them weld it up for me, so it's not like its a botched weld. When I bought the parts kit, I was told that there was an issue with it, that's why I got it so cheap.

      Originally posted by redcliff
      You may want to post your video at the Uzitalk forums, they have some pretty knowledgeable people there.
      I'm waiting for someone to activate my account...
      Originally posted by Alan Gura
      The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
      Originally posted by hoffmang
      12050[CCW] licenses will be shall issue soon.

      -Gene
      sigpic

      Comment

      • #4
        dachan
        Senior Member
        • Sep 2007
        • 1973

        Maybe your kit hasn't been modified to build a semi-auto, i.e., its still a open bolt kit.

        Comment

        • #5
          redcliff
          Calguns Addict
          • Feb 2008
          • 5676

          Originally posted by E Pluribus Unum
          When I bought the parts kit, I was told that there was an issue with it, that's why I got it so cheap.
          Hmm interesting, may want to compare function with what I posted in my edited first post.
          "You keep using that word. I do not think it means what you think it means."
          "What we get away with isn't usually the same as what's good for us"
          "An extended slide stop is the second most useless part you can put on a 1911"

          "While Ruger DA revolvers may be built like a tank, they have the aesthetics of one also,
          although I suppose there are a few tanks which I owe an apology to for that remark"

          Comment

          • #6
            E Pluribus Unum
            Calguns Addict
            • Dec 2006
            • 8098

            Nope... the gun it came from was a "Semi-Auto Only".

            It was stamped as such on the receiver.
            Last edited by E Pluribus Unum; 01-12-2011, 4:35 PM.
            Originally posted by Alan Gura
            The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
            Originally posted by hoffmang
            12050[CCW] licenses will be shall issue soon.

            -Gene
            sigpic

            Comment

            • #7
              ke6guj
              Moderator
              CGN Contributor - Lifetime
              • Nov 2003
              • 23725

              its something in the FCG, perhaps the sear is getting hung up in the sear slot in the receiver. perhaps the sear holes aren't large enough and the sear is getting bound up in the sear slot. it would be nice if you had another lower to try on it.

              Otherwise, I'd suggest looking at the FCG real good, make it is assembled properly. maybe you should completely disassemble it, clean it, and reassemble it.
              Jack



              Do you want an AOW or C&R SBS/SBR in CA?

              No posts of mine are to be construed as legal advice, which can only be given by a lawyer.

              Comment

              • #8
                E Pluribus Unum
                Calguns Addict
                • Dec 2006
                • 8098

                Originally posted by ke6guj
                its something in the FCG, perhaps the sear is getting hung up in the sear slot in the receiver. perhaps the sear holes aren't large enough and the sear is getting bound up in the sear slot. it would be nice if you had another lower to try on it.

                Otherwise, I'd suggest looking at the FCG real good, make it is assembled properly. maybe you should completely disassemble it, clean it, and reassemble it.
                I've been looking for a "lower parts kit" so I could just replace it all, but I cannot find one.

                In looking at the parts kit, the sear looks rather worn. One of the tabs is worn more than the other. It might be as simple as replacing the sear, but I'd hate to get eaten up in shipping replacing one part at a time.

                I talked to a local gunsmith and his statement was: "Uzi's are illegal, I will not work on illegal firearms."
                Originally posted by Alan Gura
                The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
                Originally posted by hoffmang
                12050[CCW] licenses will be shall issue soon.

                -Gene
                sigpic

                Comment

                • #9
                  redcliff
                  Calguns Addict
                  • Feb 2008
                  • 5676

                  Originally posted by E Pluribus Unum
                  I've been looking for a "lower parts kit" so I could just replace it all, but I cannot find one.

                  In looking at the parts kit, the sear looks rather worn. One of the tabs is worn more than the other. It might be as simple as replacing the sear, but I'd hate to get eaten up in shipping replacing one part at a time.

                  I talked to a local gunsmith and his statement was: "Uzi's are illegal, I will not work on illegal firearms."
                  Are these guys out of pistol grip assemblys? http://www.danddsales.com/parts4.html
                  "You keep using that word. I do not think it means what you think it means."
                  "What we get away with isn't usually the same as what's good for us"
                  "An extended slide stop is the second most useless part you can put on a 1911"

                  "While Ruger DA revolvers may be built like a tank, they have the aesthetics of one also,
                  although I suppose there are a few tanks which I owe an apology to for that remark"

                  Comment

                  • #10
                    E Pluribus Unum
                    Calguns Addict
                    • Dec 2006
                    • 8098

                    Originally posted by redcliff
                    Are these guys out of pistol grip assemblys? http://www.danddsales.com/parts4.html
                    I looked at their website, but I don't see just a parts kit. I see full lower FCG's for $200, but that is a bit high when all I need is an internal parts kit.
                    Originally posted by Alan Gura
                    The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
                    Originally posted by hoffmang
                    12050[CCW] licenses will be shall issue soon.

                    -Gene
                    sigpic

                    Comment

                    • #11
                      ke6guj
                      Moderator
                      CGN Contributor - Lifetime
                      • Nov 2003
                      • 23725

                      Originally posted by E Pluribus Unum
                      I've been looking for a "lower parts kit" so I could just replace it all, but I cannot find one.
                      I doubt you will find someone selling a LPK like you do for ARs. YOu would probably need to buy an entire lower assembly, or just buy the FCG parts separately.

                      In looking at the parts kit, the sear looks rather worn. One of the tabs is worn more than the other. It might be as simple as replacing the sear, but I'd hate to get eaten up in shipping replacing one part at a time.
                      with a semi-auto UZI, you are only gonna get wear on one side. The striker assembly only has one arm for the sear to engage, so you only get wear on one side. On a FA bolt, the sear engages both sides, so both sides would have wear.
                      Jack



                      Do you want an AOW or C&R SBS/SBR in CA?

                      No posts of mine are to be construed as legal advice, which can only be given by a lawyer.

                      Comment

                      • #12
                        E Pluribus Unum
                        Calguns Addict
                        • Dec 2006
                        • 8098

                        Originally posted by ke6guj
                        I doubt you will find someone selling a LPK like you do for ARs. YOu would probably need to buy an entire lower assembly, or just buy the FCG parts separately.


                        with a semi-auto UZI, you are only gonna get wear on one side. The striker assembly only has one arm for the sear to engage, so you only get wear on one side. On a FA bolt, the sear engages both sides, so both sides would have wear.
                        Do you know where I could get a sear?
                        Originally posted by Alan Gura
                        The Second Amendment now applies to state and local governments. Our lawsuit is a reminder to state and local bureaucrats that we have a Bill of Rights in this country, not a Bill of Needs
                        Originally posted by hoffmang
                        12050[CCW] licenses will be shall issue soon.

                        -Gene
                        sigpic

                        Comment

                        • #13
                          ke6guj
                          Moderator
                          CGN Contributor - Lifetime
                          • Nov 2003
                          • 23725

                          D&D sells sears for $25-30, but just because it is appears to be worn doesn't mean that that is the problem. have you confirmed that the sear can freely move up and down when the lower is pinned to the receiver? That the back of the sear isn't hitting the reciever and dragging/binding?

                          are the springs in the grip assembly installed correctly?
                          Jack



                          Do you want an AOW or C&R SBS/SBR in CA?

                          No posts of mine are to be construed as legal advice, which can only be given by a lawyer.

                          Comment

                          • #14
                            daves100
                            Senior Member
                            • Apr 2007
                            • 943

                            uzi parts

                            did you try sarco for parts

                            Comment

                            • #15
                              Taildraggerdave
                              Member
                              • Jul 2010
                              • 156

                              Post a good photo of your fcg installed in your grip frame. Remove the grip frame from the receiver and take it from the top down.
                              You should be able to push the sear down and have it hook in place for the photo. It's normal for the sear to pop up like that when the lower is not attached to the receiver.

                              Take care,
                              Dave

                              Comment

                              Working...
                              UA-8071174-1