M&p45

[CalNRA]

Could the m&p 45 been submitted before JAN 1st when both a mag disconect and LCI where needed?

then SW is more PRK friendly than I previously thought

[Black_Talon]

Anyone pick up one of these bad boys yet?

DROS-ed mine today. Only 9 days, 19 hours and 49 minutes left until I can pick it up!

[code33]

Just DROS'ed one.

Grabbed one w/ thumb safety. On the one w/o the thumb safety, there's a cutout on the frame for it and is covered. That kinda bugged me. Figure I don't have to use it if I don't want to.

[SLYoteBoy]

newb question. mag dissconnect , wont let the hammer drop if theres no mag in it? like on a p22?

[kantstudien]

Just so everyone knows, the M&P 45 must have a magazine disconnect, no matter the color or if it has a thumb safety. Thus saith the "Roster," so I wouldn't go bragging about DROSing a non-CA legal handgun if I were you, unless you want to get your FFL in trouble.

[kantstudien]

OK, I did some more research: the sku #s for at least two CA-legal M&P 45 pistols are: 307406 (thumb safety) and 307606 (no thumb safety).

[I. M. Nobody]

I received one in store the other day. I was called by wholesaler today not to sell it. All of the first ones shipped don't have the magazine disconnect. the ones shipped to calif for testing had the disconnect and these are the only ones legal in Ca.

It looks like we will have return them to wholesaler. It sure feels good in the hand though.

[TBoliv]

I received one in store the other day. I was called by wholesaler today not to sell it. All of the first ones shipped don't have the magazine disconnect. the ones shipped to calif for testing had the disconnect and these are the only ones legal in Ca.

It looks like we will have return them to wholesaler. It sure feels good in the hand though.

Too bad they can't just send out a new sear assembly. Last time I checked, Brownells had the sear assemblies (at least for 9mm) that you could just drop in for about $30.

[rorschach]

Here ya go fellas http://www.burwellgunsmithing.com/M&P.htm

[jljen]

Any updates on when the M&P45 will be available in California? All I could get out of S&W Customer Service was "soon".

BTW, the SKU #s I got from S&W are:
109006 - Mag Safety, Thumb Safety
109206 - Mag Safety

The SKU #s listed earlier in this thread, 307406 and 307606 are LE only SKU #s.

[SnWnMe]

To those who have handled them, how do they compare to the 9/40 models?

[U2BassAce]

Any updates on when the M&P45 will be available in California? All I could get out of S&W Customer Service was "soon".

BTW, the SKU #s I got from S&W are:
109006 - Mag Safety, Thumb Safety
109206 - Mag Safety

The SKU #s listed earlier in this thread, 307406 and 307606 are LE only SKU #s.

I saw one at On Target in Laguna Niguel the other night. I have also shot one. Very nice!! I pick mine up on Wed this week!

[Black_Talon]

I pick mine up on Wed this week!

What SKU is yours, and where did you buy it?

[Rugerman]

[U2BassAce]

What SKU is yours, and where did you buy it?

It is sitting at the FFL right now. I pick it up on Wed. I will get the SKU then. I bought it from a small FFL. He had one of the first in the state about a month ago. "that is the one I shot" However that one did not have the mag disconect. It did have the ambi safety.

Mine has no ambi safety but does have mag disc.

I mentioned above I saw one at On Target. I might have mistaken. I did not handle it. But did take a close look through the case. It might have been a 40 because another member here called and was told they have not received one yet.

Oh of course pictures on Wed.