Unconfigured Ad Widget

Collapse

Flame cutting?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SarcoBlaster
    Senior Member
    • Jun 2006
    • 1775

    Flame cutting?

    I picked up my Ruger LCR yesterday and put 50 Winchester 130gr. FMJ rounds through it. After cleaning the gun, I noticed this:


    Flame cutting? Tooling mark? Anybody else experience this with their LCR's?
    Last edited by SarcoBlaster; 06-26-2010, 7:10 PM.
    My buyer/seller feedback.
  • #2
    kurac
    Veteran Member
    • Dec 2005
    • 2917

    keep shooting, then you will see a flame cut, that might be just the beginning
    www.culinagrips.com
    "custom grips for shooters by shooters"

    Comment

    • #3
      Revoman
      Senior Member
      • Dec 2007
      • 2394

      I'm no expert, but that does not look like flame cutting to me, a simple tool mark is what I would suspect.

      I think that flame cutting would occur a little more on the top strap and not where it shows now. Also, it should not happen with only 50 rounds.

      Comment

      • #4
        den888
        I need a LIFE!!
        • Jul 2009
        • 10520

        Should not happen with that low of a round count.

        I have broken-in 5 different .357 magnum revolvers of various makes. A least on the ones I have had, you start to see flame cutting around 800+ rounds.

        Comment

        • #5
          Verci0013
          Member
          • Mar 2010
          • 496

          I didn't want to make another thread so please pardon my lack of knowledge, but what exactly is "flame cutting?"

          Comment

          • #6
            Doheny
            I need a LIFE!!
            • Sep 2008
            • 13820

            Originally posted by Verci0013
            I didn't want to make another thread so please pardon my lack of knowledge, but what exactly is "flame cutting?"
            Sent from Free America

            Comment

            • #7
              Turbinator
              Administrator
              CGN Contributor - Lifetime
              • Oct 2005
              • 11993

              Originally posted by Doheny
              Umm, no.

              Flame cutting - so, revolvers have a cylinder gap. Every time you fire, some of the blast escapes through the cylinder gap - this is the small space between the front of the cylinder and the forcing cone on the revolver. Eventually this escaping hot burning gas starts to wear into the top strap, hence the name "flame cutting".

              Turby

              Comment

              • #8
                Verci0013
                Member
                • Mar 2010
                • 496

                Originally posted by Doheny
                Where is the second flame coming from!?

                Originally posted by Turbinator
                Umm, no.

                Flame cutting - so, revolvers have a cylinder gap. Every time you fire, some of the blast escapes through the cylinder gap - this is the small space between the front of the cylinder and the forcing cone on the revolver. Eventually this escaping hot burning gas starts to wear into the top strap, hence the name "flame cutting".

                Turby
                Thank you Turby

                Comment

                • #9
                  humgunner
                  Junior Member
                  • Mar 2010
                  • 89

                  I assume you mean this spot?



                  Not flame cutting. The finish is still intact. Looks like a tool mark that was made prior to the finish being applied.
                  I've put over 2k rounds through mine without a problem. That spot gets alot of wear. The finish on mine started to erode just above the forcing cone after a few hundred rounds but no flame cutting yet.
                  Over five thousand years ago, Moses said to the children of Israel , "Pick up your shovels, mount your asses and camels, and I will lead you to the Promised Land."

                  Nearly 75 years ago (when Welfare was introduced) the democrat party said, "Lay down your shovels, sit on your asses, and light up a Camel, this is the Promised Land."

                  Now obama and the dems have stolen your shovel, taxed your asses, raised the price of Camels,
                  and mortgaged the Promised Land!

                  Comment

                  • #10
                    SarcoBlaster
                    Senior Member
                    • Jun 2006
                    • 1775

                    Originally posted by humgunner
                    I assume you mean this spot?



                    Not flame cutting. The finish is still intact. Looks like a tool mark that was made prior to the finish being applied.
                    I've put over 2k rounds through mine without a problem. That spot gets alot of wear. The finish on mine started to erode just above the forcing cone after a few hundred rounds but no flame cutting yet.
                    Yessir, that's the spot I'm talking about. A member on another forum also mentioned that it's most likely a tool mark because he only has 30 rounds through his and has the same mark on his gun.

                    I suppose I can breathe a sigh of relief!
                    My buyer/seller feedback.

                    Comment

                    • #11
                      Marlin Hunter
                      Senior Member
                      • Mar 2010
                      • 586

                      Originally posted by SarcoBlaster
                      Yessir, that's the spot I'm talking about. A member on another forum also mentioned that it's most likely a tool mark because he only has 30 rounds through his and has the same mark on his gun.

                      I suppose I can breathe a sigh of relief!

                      It looks like tool marks as other have said, but you can get flame/gas cutting with only 30 rounds. I have flame cutting with only 21 rounds out of my 357 mag.


                      check out this post

                      Last edited by Marlin Hunter; 06-27-2010, 10:40 AM.
                      *
                      *
                      *

                      Comment

                      • #12
                        Army
                        Veteran Member
                        • Oct 2005
                        • 3915

                        No evidence that flame cutting will compromise the strength of the topstrap, regardless of extent. Forget it, and shoot.
                        "A nation can survive its fools, and even the ambitious. But it cannot survive treason from within. An enemy at the gates is less formidable, for he is known and carries his banner openly. But the traitor moves amongst those within the gate freely, his sly whispers rustling through all the alleys, heard in the very halls of government itself...A murderer is less to fear. The traitor is the plague."......Cicero

                        Comment

                        • #13
                          Turbinator
                          Administrator
                          CGN Contributor - Lifetime
                          • Oct 2005
                          • 11993

                          30 rounds certainly is not going to induce flame cutting, IMHO. I can speak from my own experience, I have not seen any evidence of flame cutting over the past 10+ years in revolvers I've used, definitely with more than 30 rounds through them.

                          Turby

                          Comment

                          • #14
                            bjl333
                            C3 Contributor
                            CGN Contributor - Lifetime
                            • Dec 2009
                            • 7010

                            Originally posted by Marlin Hunter
                            It looks like tool marks as other have said, but you can get flame/gas cutting with only 30 rounds. I have flame cutting with only 21 rounds out of my 357 mag.


                            check out this post

                            http://forums.handloads.com/forum_po...TID=19210&PN=1


                            Damn, that revolver has it bad !!!
                            Wanna learn to shoot SKEET? I am here to introduce all shooters to the sport of SKEET Shooting ....
                            CLICK HERE TO FIND OUT >>> SoCal Skeet Clinic
                            SKEET SHOOTING CLINIC
                            sigpic

                            Comment

                            • #15
                              shooting4life
                              Calguns Addict
                              • Jan 2009
                              • 5771

                              If you want to see flame cutting do a search for 357 maximum shooting 125gr bullets.

                              Comment

                              Working...
                              UA-8071174-1