ar pistol registration

[Ryan C]

my registration has been rejected because name ,city, and state is not engraved on firearm is that required and what are my options

[Michael777]

Get a fixed mag device. Better than A bullet button.

[solidfreshdope]

my registration has been rejected because name ,city, and state is not engraved on firearm is that required and what are my options

Are you asking about voluntary registration or Assault Weapon registration for SB880?

As AW registration deadline has passed, you will not be able to go that route.

Your AR pistol, if semiauto will need to have a fixed mag that requires the action to be disassembled in order to release the magazine.

You will need to request a serial number for your home build from the CA DOJ using form BOF 1008.

You will need to have this serial number along with other ATF required markings engraved within 10 days of receipt of the serial number.


Sent from my iPhone using Tapatalk Pro

[zeroman03]

my registration has been rejected because name ,city, and state is not engraved on firearm is that required and what are my options

I believe since the 7/1/18 deadline has passed, you may now have to submit a request for a non-BBAW, DOJ assigned serial number. The last time I read through some of these threads however, it seemed like the DOJ was not yet issuing SNs for non-BBAWs. I would imagine that once you receive such serial number, you could then have it engraved, along with the other missing/requested info, onto the firearm. Other options would probably be non-compliance, destroy, or remove from the state. IDK

Sent from my SAMSUNG-SM-G920A using Tapatalk

[edgerly779]

Yes engraving must have your name, city, state,& caliber and serial number . Been many posts on this and had to be done before 7/1/2018 or you must apply for serial number.

[Ryan C]

already has the assigned doj serial number that I got laser engraved and was registered before july 1st but I didn't put the city and name is that required the doj is saying it is?

[beanz2]

Is it an outright rejection or an Incomplete Notice? The latter gives you an opportunity to correct it still. We tend to confuse the two.

If an Incomplete, you may still be able to engrave it and resubmit.

[edgerly779]

yes it is required. look up pc.

[Ryan C]

thanks everyone its incomplete so I'm just gonna add it on there and should be gtg I hope

[ladiver]

already has the assigned doj serial number that I got laser engraved and was registered before july 1st but I didn't put the city and name is that required the doj is saying it is?

I am surprised the company doing the engraving did not tell you about the Name/City/State requirement. Must not have been an engraver that works with firearms much.

I had a few difficulties with engravers because they felt that the FMBUS number identified it as an AW (even prior to registration) and they could not do it without me being on-site. I looked up the requirements from CADOJ and it clearly states that engraving MAY be done at FFL07.

"Upon receipt of your serial number(s), you may contact a Federal Firearms Licensed Manufacturer (type 07) to have your Department issued serial number applied in a manner consistent with the requirements outlined in the California Code of Regulations, title 11, section 5474.2"

[walmart_ar15]

I am surprised the company doing the engraving did not tell you about the Name/City/State requirement. Must not have been an engraver that works with firearms much.

I had a few difficulties with engravers because they felt that the FMBUS number identified it as an AW (even prior to registration) and they could not do it without me being on-site. I looked up the requirements from CADOJ and it clearly states that engraving MAY be done at FFL07.

"Upon receipt of your serial number(s), you may contact a Federal Firearms Licensed Manufacturer (type 07) to have your Department issued serial number applied in a manner consistent with the requirements outlined in the California Code of Regulations, title 11, section 5474.2"

It is not an AW if just drop off the stripped receiver at FFL07.

[Jimi Jah]

Mine was built and engraved with name, town, caliber and s/n number years ago before all this registration crap. I knew it would be needed for at least ID purposes. A Franklin DFM mag was all I did for it.

Having been born here I could smell this stuff coming from years away.