Tweet
I have a custom machined ammo loading block/tray from the latest batch. Selling the limited number of excess blocks. These are true custom blocks for my fellow CalGuns members.
Here are the features of these custom blocks:
1. CNC machined from a solid block of 6061 T6 aircraft aluminum. Finished block is massive at 6.65" by 3.45" and a full 1” thick weighing almost 2 lbs.
2. Cartridge specific machined cartridge holes with chamfered mouth opening ensuring rapid brass insertion with minimal brass wiggle avoiding powder spillage.
3. Caliber markings are engraved on both sides of the block for a nice look. Custom engraving of your choosing is also available.
4. Relief cut machined for primer protection and safety. The primer does not contact with the bottom of the block.
5. Smooth corners and radius edges ensure snag free while protecting other things on your bench from being scratched/dented by sharp corners.
6. Rubber feet prevents damage and sliding on your bench. Plenty of weight on these blocks that if bumped it will not spill powder all over your bench.
7. Smooth surface will stay clean longer and is easy to polish with metal polish should the need arise.
8. Can be used on your loading bench or at the range or on your office desk.
If you are using a plastic tray now and you use one of these, you will give your plastic blocks to your neighbors that always borrow stuff from you.
I have extra blocks from a batch that I am selling off. A very limited quantity and calibers are available to fellow CalGuns members at $35 each FTF or add shipping cost to your door. Other calibers are available upon request.
Pics of current available calibers.
My 30-06 reloads on HXP 78 brass.
Swiss GP11 7.5x55mm Swiss factory ammo.
Close up of the holes showing the chamfered mouth. If you look down the bottom of the hole you can see the relief cut for primer clearance.
Close up of side markings on .30-06, 9mm, U.S. RIFLE CAL .30 M1, .308/7.62 & .223/5.56.
Close up of side markings on .22 LR, .40 S&W, .45 ACP, 6.5x55 Swedish & 7.5x55 Swiss.
Here are the features of these custom blocks:
1. CNC machined from a solid block of 6061 T6 aircraft aluminum. Finished block is massive at 6.65" by 3.45" and a full 1” thick weighing almost 2 lbs.
2. Cartridge specific machined cartridge holes with chamfered mouth opening ensuring rapid brass insertion with minimal brass wiggle avoiding powder spillage.
3. Caliber markings are engraved on both sides of the block for a nice look. Custom engraving of your choosing is also available.
4. Relief cut machined for primer protection and safety. The primer does not contact with the bottom of the block.
5. Smooth corners and radius edges ensure snag free while protecting other things on your bench from being scratched/dented by sharp corners.
6. Rubber feet prevents damage and sliding on your bench. Plenty of weight on these blocks that if bumped it will not spill powder all over your bench.
7. Smooth surface will stay clean longer and is easy to polish with metal polish should the need arise.
8. Can be used on your loading bench or at the range or on your office desk.
If you are using a plastic tray now and you use one of these, you will give your plastic blocks to your neighbors that always borrow stuff from you.
I have extra blocks from a batch that I am selling off. A very limited quantity and calibers are available to fellow CalGuns members at $35 each FTF or add shipping cost to your door. Other calibers are available upon request.
Pics of current available calibers.
My 30-06 reloads on HXP 78 brass.
Swiss GP11 7.5x55mm Swiss factory ammo.
Close up of the holes showing the chamfered mouth. If you look down the bottom of the hole you can see the relief cut for primer clearance.
Close up of side markings on .30-06, 9mm, U.S. RIFLE CAL .30 M1, .308/7.62 & .223/5.56.
Close up of side markings on .22 LR, .40 S&W, .45 ACP, 6.5x55 Swedish & 7.5x55 Swiss.
Comment