Tweet
The best tools for your AK build...
AK Builder 7.62 5.45 Receiver Blank Drilling Fixture $85
* For bent Polish 7.62x39 and 5.45x39 receiver blanks
* Drills hammer pin, trigger pin, selector lever, center support and trigger guard holes
* Includes drill bits: 5/32", 7/32", 5mm, 7mm, 10mm
* Stop pin is key to getting receiver aligned in fixture
* Heat treated to extend service life
MADE IN THE USA
NOTE: Will NOT work on Polish Tantal since selector hole is in different spot.
---
AK Builder 7.62 5.45 Trunnion Rivet Hole Drilling Fixture $70
* Drills front and rear trunnion rivet holes
* Red expanding mandrel fits 7.62 trunnions
* Blue expanding mandrel fits 5.45 trunnions
* Works with any rear trunnion
MADE IN THE USA
---
AK Builder Trigger Guard Rivet Jig $60
* Front four rivets can be set first, rear rivet done separately
* Magnet holds rear rivet support block in place
* Remove support block for flats that have front trigger guard holes in wrong place
* Removing support block gives clearance for a rear reinforcement plate
MADE IN THE USA
---
AK Builder Barrel Press Kit $90
* Barrel removal/installation and cross-pinning on stamped AK receivers
* Works with 1" ram on 12 ton hydraulic shop press
* AKM trunnion support block with leveling screws
* Barrel pin ram adapter with different size pins
* Barrel press bolt with brass alignment nut
* Steel barrel press support bar set
MADE IN THE USA
---
AK Builder Receiver Flat Bending Die Set $175
* Properly bends and forms an AK receiver flat
* Works with a 12-ton (or more) shop press
* 1mm (0.040") punch has alignment pins for 7.62 and 5.45 flats
* Set screws help remove punch assembly from lower die
* Lower die is made from steel and machined to 14.5 lbs
MADE IN THE USA
---
AK Builder Rivet Tool $265
* Installs front/rear trunnion rivets and center support
* Allows proper peening of all swell neck trunnion rivets
* Protects receiver from accidental crushing during center support installation
* Includes dimpling, rivet alignment and head forming tools
* Large ram, ram arm are made from 4140 steel and heat treated
MADE IN THE USA
NOTE: Will NOT install trigger guard rivets.
---
AK Builder Front Sight Gas Block Support $25
* Helps remove/install gas block and front sight pins
* Laser engraved outline shows proper layout
* Hard coat anodized aluminum
MADE IN THE USA
AK Builder 7.62 5.45 Receiver Blank Drilling Fixture $85
* For bent Polish 7.62x39 and 5.45x39 receiver blanks
* Drills hammer pin, trigger pin, selector lever, center support and trigger guard holes
* Includes drill bits: 5/32", 7/32", 5mm, 7mm, 10mm
* Stop pin is key to getting receiver aligned in fixture
* Heat treated to extend service life
MADE IN THE USA
NOTE: Will NOT work on Polish Tantal since selector hole is in different spot.
---
AK Builder 7.62 5.45 Trunnion Rivet Hole Drilling Fixture $70
* Drills front and rear trunnion rivet holes
* Red expanding mandrel fits 7.62 trunnions
* Blue expanding mandrel fits 5.45 trunnions
* Works with any rear trunnion
MADE IN THE USA
---
AK Builder Trigger Guard Rivet Jig $60
* Front four rivets can be set first, rear rivet done separately
* Magnet holds rear rivet support block in place
* Remove support block for flats that have front trigger guard holes in wrong place
* Removing support block gives clearance for a rear reinforcement plate
MADE IN THE USA
---
AK Builder Barrel Press Kit $90
* Barrel removal/installation and cross-pinning on stamped AK receivers
* Works with 1" ram on 12 ton hydraulic shop press
* AKM trunnion support block with leveling screws
* Barrel pin ram adapter with different size pins
* Barrel press bolt with brass alignment nut
* Steel barrel press support bar set
MADE IN THE USA
---
AK Builder Receiver Flat Bending Die Set $175
* Properly bends and forms an AK receiver flat
* Works with a 12-ton (or more) shop press
* 1mm (0.040") punch has alignment pins for 7.62 and 5.45 flats
* Set screws help remove punch assembly from lower die
* Lower die is made from steel and machined to 14.5 lbs
MADE IN THE USA
---
AK Builder Rivet Tool $265
* Installs front/rear trunnion rivets and center support
* Allows proper peening of all swell neck trunnion rivets
* Protects receiver from accidental crushing during center support installation
* Includes dimpling, rivet alignment and head forming tools
* Large ram, ram arm are made from 4140 steel and heat treated
MADE IN THE USA
NOTE: Will NOT install trigger guard rivets.
---
AK Builder Front Sight Gas Block Support $25
* Helps remove/install gas block and front sight pins
* Laser engraved outline shows proper layout
* Hard coat anodized aluminum
MADE IN THE USA
Comment