Unconfigured Ad Widget

Collapse

CNC Setups

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • edittman1
    Senior Member
    • Jan 2006
    • 535

    CNC Setups

    Looking at the ghost gunner, I want to make my own setup. Can someone point me in the right direction for threads with info on CNC options, software, drill bits, etc. to make my own setup that offers more versatility.

    TIA
  • #2
    yari
    Senior Member
    • Nov 2010
    • 908

    Practical machining forum. CNC zone forum. Hoss CNC on YouTube. Yes hoss not Haas.

    Comment

    • #3
      xfer42
      CGN/CGSSA Contributor
      CGN Contributor
      • Sep 2007
      • 709

      Are you going to retrofit a small or mini mill?
      If so check out cncfusion.

      Decide whether you are going stepper or servo, then look up the parts on ebay.

      Steppers are usually cheaper, but can lose step.
      Servos are closed loop (an encoder tells the driver exactly where the motor is), This setup can be more expensive.


      Software:
      LinuxCNC is opensource(free).
      Mach3 is commercial and requires Windows.

      Drives:
      Gecko (they make stepper and servo drives)

      Motors:
      Ebay (search for "brushed DC servo with encoder" and "stepper nema 17", "stepper nema 23", "stepper nema 34")
      Last edited by xfer42; 10-21-2014, 12:14 PM.

      Comment

      • #4
        arga
        Member
        • Jul 2010
        • 146

        pycam
        freecad
        f-engrave
        hobbycnc
        linuxcnc
        HarborFreight mini mill
        CNC conversion plans (Little Machine Shop has some w/ a complete BOM but there are others on the net)

        The above list is completely doable and it's relatively cheap compared to everything else except the Ghost Gunner. It's also a complete pain. The stepper motors bind, the software is buggy and/or has a steep learning curve. It's all manageable but I have to say that $5k doesn't seem so bad anymore for a "real" CNC machine. Still, if you have the time, have more skill than I do (consider me somewhere in the middle), and don't mind a challenge then it's not a bad option.

        Comment

        • #5
          bksa
          Senior Member
          • Dec 2011
          • 2012

          For a X2 CNC'ed you're looking at around $1500, + additional tooling cost and time spent converting / tuning it.

          Comment

          • #6
            milotrain
            Veteran Member
            • Apr 2011
            • 4301

            Without a huge amount of overhaul the bench-top Chinese mills don't do well as CNC machines. Look at Tormach, Haas Minimill, or Ganesh CNCd knee mill. All are $8k (or more), all want 220, all will take another $4k in tooling to get working the way you want.
            weg: That device is obsolete now. They replaced it with wizards.
            frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

            Comment

            • #7
              bksa
              Senior Member
              • Dec 2011
              • 2012

              Originally posted by milotrain
              Without a huge amount of overhaul the bench-top Chinese mills don't do well as CNC machines. Look at Tormach, Haas Minimill, or Ganesh CNCd knee mill. All are $8k (or more), all want 220, all will take another $4k in tooling to get working the way you want.
              they all need a fairly large size space as well.

              benchtop machines work well if you're willing to put in the time to work on them, but they can definitely perform decently well.

              Comment

              • #8
                arga
                Member
                • Jul 2010
                • 146

                Maybe we need to come together as a community and solve some of these issues because $8k is just too damn much especially when you consider there's still tooling and SW to buy (if you don't want to work with open source).

                For example, most of my problems with CNC X2 right now are related to the motors binding. That's absolutely fixable with some time. I have the parts to replace the lead screws with ball screws but I won't be able to get to that until mid-winter.

                EMC2/LinuxCNC (same thing) has an ugly learning curve but I was getting the hang of it before I tabled this project.

                Comment

                • #9
                  ar15barrels
                  I need a LIFE!!
                  • Jan 2006
                  • 57202

                  Originally posted by arga
                  For example, most of my problems with CNC X2 right now are related to the motors binding.

                  Easy fix.
                  Reduce the binding or increase the power of the motors to be able to overcome the binding.
                  Reducing the binding is the more elegant solution.
                  Randall Rausch

                  AR work: www.ar15barrels.com
                  Handguns: www.handgunbarrels.com
                  Bolt actions: www.700barrels.com
                  Foreign Semi Autos: www.akbarrels.com
                  Most work done while you wait on a scheduled shop visit.

                  Comment

                  • #10
                    milotrain
                    Veteran Member
                    • Apr 2011
                    • 4301

                    8k isn't too much when you see what goes into manufacturing these machines. You could totally build an open source CNC machine based on linear rail but you won't save much over $8k, and you won't save anything after factoring in your time.
                    weg: That device is obsolete now. They replaced it with wizards.
                    frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                    Comment

                    • #11
                      arga
                      Member
                      • Jul 2010
                      • 146

                      I work with engineers. I was shamed out of using larger motors.

                      The binding is clearly the result of my poor craftsmanship. A lot of that comes from me trying to use a mill to do work that should be done on a lathe.

                      It brings up a good point, though. The plans I followed mount the motors in-line with the lead screws. There are other designs out there that mount the motors parallel but offset from the lead screws then connect them with a belt. It looks like this would be more tollerent of poor craftsmanship. This also provides an easy way to increase torque at the cost of speed by changing out the pullies. If anyone here has had luck with that design then speak up. We can make it part of our Calguns CNC recipe.

                      Comment

                      • #12
                        xfer42
                        CGN/CGSSA Contributor
                        CGN Contributor
                        • Sep 2007
                        • 709

                        I built mine with servos. One day, I was in the middle of cutting out some XL 650 tool heads and decided to park it. I issued a G0 X0 Y0, locked the gibs, and shut the machine off for the night. Next day, I continued cutting and smelled something burning. It was the servos! I forgot to unlock the gibs. I swear, I could light a cigarette on them. It was another reminder that this thing could eat me and itself up without tripping the current limiter.

                        Comment

                        • #13
                          ar15barrels
                          I need a LIFE!!
                          • Jan 2006
                          • 57202

                          Originally posted by xfer42
                          locked the gibs, and shut the machine off for the night.

                          Why lock the gibs?
                          Won't your machine home itself and reacquire zero at startup?
                          Randall Rausch

                          AR work: www.ar15barrels.com
                          Handguns: www.handgunbarrels.com
                          Bolt actions: www.700barrels.com
                          Foreign Semi Autos: www.akbarrels.com
                          Most work done while you wait on a scheduled shop visit.

                          Comment

                          • #14
                            xfer42
                            CGN/CGSSA Contributor
                            CGN Contributor
                            • Sep 2007
                            • 709

                            It will stay zeroed if I leave it all still. The ball screws are 5TPI, and bumping the table will rotate the servos when they are not on. The X & Y were zeroed on the edge of the work piece.

                            Comment

                            • #15
                              ar15barrels
                              I need a LIFE!!
                              • Jan 2006
                              • 57202

                              Originally posted by xfer42
                              It will stay zeroed if I leave it all still. The ball screws are 5TPI, and bumping the table will rotate the servos when they are not on. The X & Y were zeroed on the edge of the work piece.

                              Don't you have absolute scales or a precision limit switch to zero from?
                              Randall Rausch

                              AR work: www.ar15barrels.com
                              Handguns: www.handgunbarrels.com
                              Bolt actions: www.700barrels.com
                              Foreign Semi Autos: www.akbarrels.com
                              Most work done while you wait on a scheduled shop visit.

                              Comment

                              Working...
                              UA-8071174-1