Unconfigured Ad Widget

Collapse

Another quick AK question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Pauliedad
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2012
    • 2095

    Another quick AK question

    Me and my home build polish again. This is my first and as stated in previous post, I see more of these in my future so no need for this one to be perfect but don't want a train wreck either. That said....

    #1. When I located the rear trunnion I was focused on the stock fitting just so instead of the dust cover. That won't happen again. So do I refit the trunnion? I can tigweld and re drill or do I just dremel down the front of the dust cover?
    Putting this in writing, the second definitely sounds more Bubba.

    #2. I put together the trigger group it came with and the trigger and disconnect are not the type that have a sleeve. That's fun.
    What is the preferred method for pin retention? Plate? Spring? Would like to skip learning the hard way on this portion.

    #3. I went with a pre bent %80 that already had the slide spot welded and after I got all done went with a cold black finish. Kindof lame. I'll do the proper hot parkerizing next time.
    Anyhoo, I'm thinking I'll just go with this for now. Looks very Mad Max.

    #4. Where can I get more kits?
    Got this one from Apex and got a new barrel for it too. Should I keep doing that or are there other sources y'all AK fiends can turn a guy on to?

    Think ill buy a jig and bend on my own next time. Maybe a weld build.
    Oh wait, I just bought the riveting tool. Oh hell. What will I do with all these?
  • #2
    kcstott
    I need a LIFE!!
    • Nov 2011
    • 11796

    1) your operating spring also locates off the rear trunnion and if it's to far forward your bolt carrier will hammer it back.
    Pull the trunnion weld up your holes and start over.

    2) I like the retainer plate

    3) it's up to you.

    4) What A country, Apex, etc.

    Don't do a weld build, nor a screw build (And this coming from a guy that his first build was a screw build. Not anymore) it will crack. the sheet metal is to thin for a weld to hold up. Do not discount the strength of rivets. I work on large industrial cranes for a living and occasionally we run into a pre 1940's crane that is all riveted construction. The damn things are built to last. There is one crane still in use at Miramar MCAS it's and old fish belly P&H if I remember correctly they still use it daily. The only bad thing about riveted construction is it was (is) time consuming. thats it. the joints are strong and in most cases stronger then a welded joint.
    Last edited by kcstott; 12-20-2013, 8:50 PM.

    Comment

    • #3
      Pauliedad
      CGN/CGSSA Contributor - Lifetime
      CGN Contributor - Lifetime
      • Dec 2012
      • 2095

      Makes sense. I get the idea of brittle and having the rivets take the stress. Good point. I got the idea from Usmcdoc14 on YouTube. Entertaining guy. Thanks for the input.

      Comment

      • #4
        kcstott
        I need a LIFE!!
        • Nov 2011
        • 11796

        Originally posted by Pauliedad
        Makes sense. I get the idea of brittle and having the rivets take the stress. Good point. I got the idea from Usmcdoc14 on YouTube. Entertaining guy. Thanks for the input.
        if you folded up a 1/8" receiver then yeah weld it to the trunnions. but not on a 1/16" thick receiver or a 1mm

        you'd have to do so much to make the design compatible with welding it's not worth it. You already bought the tools, use them. you won't regret it.

        I was fusing my self the entire time I was welding up my screw holes and redrilling not the trunnion the receiver. I should have just started over with a new flat. but I didn't want to do that. I did have to repark though.

        Comment

        • #5
          Pauliedad
          CGN/CGSSA Contributor - Lifetime
          CGN Contributor - Lifetime
          • Dec 2012
          • 2095

          Is the hot parkerizing gtg for finish or use that as a base for something better? Next one needs to be pretty. Redone wood and all.

          Comment

          • #6
            valley82
            Veteran Member
            • Dec 2011
            • 2768

            I love an AKM in oiled park. But my HK 93 I parked (no oil) then duracoated it HK black and it came out really good! I think, cerecoat is better straight over blasted metal, but someone with actual knowledge will chime in I'm sure.

            Comment

            • #7
              p220nut
              Senior Member
              • Feb 2011
              • 508

              #4. Where can I get more kits?
              Arms of America
              R guns
              Atlantic fire arms

              you have been bitten by the AK snake!
              Love AK's
              Hate AR's

              Comment

              • #8
                tujungatoes
                Calguns Addict
                • Dec 2006
                • 7942

                Originally posted by Pauliedad
                Me and my home build polish again. This is my first and as stated in previous post, I see more of these in my future so no need for this one to be perfect but don't want a train wreck either. That said....

                #1. When I located the rear trunnion I was focused on the stock fitting just so instead of the dust cover. That won't happen again. So do I refit the trunnion? I can tigweld and re drill or do I just dremel down the front of the dust cover?
                Putting this in writing, the second definitely sounds more Bubba.

                #2. I put together the trigger group it came with and the trigger and disconnect are not the type that have a sleeve. That's fun.
                What is the preferred method for pin retention? Plate? Spring? Would like to skip learning the hard way on this portion.

                #3. I went with a pre bent %80 that already had the slide spot welded and after I got all done went with a cold black finish. Kindof lame. I'll do the proper hot parkerizing next time.
                Anyhoo, I'm thinking I'll just go with this for now. Looks very Mad Max.

                #4. Where can I get more kits?
                Got this one from Apex and got a new barrel for it too. Should I keep doing that or are there other sources y'all AK fiends can turn a guy on to?

                Think ill buy a jig and bend on my own next time. Maybe a weld build.
                Oh wait, I just bought the riveting tool. Oh hell. What will I do with all these?
                1. If it's just a hair long you can trim the dust cover. Actually sometimes you can cheat and just tweak the rear of the cover in to get it to fit. Beyond that, weld it up and relocate the holes.

                2. Most foreign trigger groups are going to need a spacer inside the trigger to take up the space left by the missing rate reducer. Also don't forget to remove the catch on the hammer for the auto sear, and the tail on the back of the disconnector. Most guys just swap the trigger group out to get 3 easy 922r compliance parts. As far as pin retention, the red star retainer plate is the shizzle my nizzle.

                3. Finish really is up to you. Park, alumahyde, cerakote, duracoat...I have several that are just krylon'd. It's quick cheap and dirty. Plus if it looks like sh*t you can always touch it up. Regarding park, it's really not so much a finish as it is surface prep.

                4. Apex, akbuilder, whatacountry, desert fox sales, centerfire, CGN marketplace, gunbroker.....the list goes on.
                Last edited by tujungatoes; 12-20-2013, 10:23 PM.
                sigpic
                Originally posted by Dr. Elky
                If your a man who wears white sunglasses, your probably a douche bag
                Originally posted by CSACANNONEER
                I've been know to cross dress and go the other way at certain events.

                Comment

                • #9
                  kcstott
                  I need a LIFE!!
                  • Nov 2011
                  • 11796

                  Oiled park is fine as is but park is a great base for alumahide gunkote and durakote, I don't recommend it for cerokote. Cerokote is very picky about how clean the surface is that it sticks to. mild contamination will ruin a cerokote job.

                  Not saying it can't be done just a lot of stuff to pay attention to. Usual route is blast, soak, bake, cool, coat, bake, and good to go. add parkerize in there and you soak time goes up and you still need to bake it out then you run into the potential for flash rust.

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    1) The first thing to try is to tweek the rear bottom portion of the cover a bit. This works well most of the time. I've used a leatherman to do it so, it can be a very simple solution. Removing metal should be a last resort AFTER someone with experience looks at it and can't tweek it for you.

                    2)REDSTAR (not Tapcp) retainer plates are worth every penny and are one of the few aftermarket, non original parts which I truely feel are an "upgrade" instead of just making it a hack bubba job.

                    3)You can always refinish and or rebuild and refinish this build at a later date.

                    4) The hunt is on. Many places deal in parts kits and you can also find them in places like the marketplace here.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      hardstatic
                      Junior Member
                      • Aug 2012
                      • 17

                      #2 - Why wouldn't you get a US-made trigger group? That's 3 parts right there for 922r compliance. Seems like a no-brainer. And yes, get the plate retainer.

                      #4 - ak-builder.com, k-var.com, armsofamerica.com, and check the the marketplace here both commercial and private.

                      Comment

                      • #12
                        Ibn Hakkan
                        Banned
                        • Dec 2013
                        • 86

                        what does your kit look like? I'm thinking about picking one up but I'm nervous about what it looks like. I've seen some that are real nice and others look like they've been through hell and back

                        Comment

                        • #13
                          Marcus von W.
                          Banned
                          • Apr 2010
                          • 1675

                          Originally posted by p220nut
                          #4. Where can I get more kits?
                          Arms of America
                          R guns
                          Atlantic fire arms

                          you have been bitten by the AK snake!

                          I have an all matching, original finish, good condition, Polish AKM underfolder kit for $375 shipped. For another $350 I have a Polish barreled trunnion assembly (trunnion, barrel, both sights, gas block, lower handguard retainer) that would be excellent for building the kit - sell the trunnion and barrel parts, and you would have a nice original barrel for around $200.

                          I also have a Soviet 1970 Izhevsk kit with no front trunnion (these are available from Desert Fox Outfitters for $200, or use something like a re-numbered Romanian) for $400 + shipping.

                          Comment

                          • #14
                            Atlantic Firearms.com
                            Vendor/Retailer
                            • Dec 2007
                            • 852

                            We have some Polish Kits in stock



                            Atlantic Firearms.com
                            410 352 5183
                            sales@atlanticfirearms.com
                            www.atlanticfirearms.com

                            Comment

                            • #15
                              Pauliedad
                              CGN/CGSSA Contributor - Lifetime
                              CGN Contributor - Lifetime
                              • Dec 2012
                              • 2095

                              Update:
                              Went ahead and tig welded the holes, ground them, and re drilled. Good call. Only took about an hour.
                              Dust cover fits like a glove.
                              My kit looked ok. Blueing was pretty good on sites, trunnions, gas tube. Wood is not all beat too bad and dust cover could use something.
                              Numbers are all matching.

                              For the next one I went with an "excellent condition" Yugo from apex.
                              Yeah, I'll just get the 922 trigger.
                              Fun times.

                              Comment

                              Working...
                              UA-8071174-1