Unconfigured Ad Widget

Collapse

Done

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • doh31672
    Member
    • Oct 2010
    • 471

    Done

    delete
    Last edited by doh31672; 02-12-2014, 1:43 PM.
  • #2
    SMarquez
    Senior Member
    • Jun 2011
    • 2216

    What type of magazines are you using. If the failures are out of the same mag, the problem is obvious. What type of ammo? I switched a PSA upper onto a Mega lower and JD Machines lower with zero function issues. I did have issues with some cheap gun show mags.

    Comment

    • #3
      woods
      Member
      • Mar 2011
      • 477

      Check your ammo I've had bad ammo do this to me in the past. how was it grouping when it failed?

      The buffer tube plunger usually is adjustable. It's got weights inside you can try taking one out.

      Check your magazines for burrs or nicks. Try to exchange them and compare. Clean your upper and grease and oil to spec. Take out your bolt carrier group and inspect that you have a tight gas system.

      It's easy enough to check the gas block and tube yourself. Just more time consuming.

      Finally a lot of foreign made ammo can leave a lacquer in the chamber and you should use a chamber brush and a good solvent. The rounds might be expanding and getting somewhat stuck losing power during extraction.
      Last edited by woods; 08-11-2013, 11:32 AM.

      Comment

      • #4
        bryant
        Member
        • Nov 2012
        • 220

        check gas block maybe got loose or bcg gas pipe.

        Comment

        • #5
          6mmintl
          Veteran Member
          • Apr 2008
          • 4822

          Carbon buildup inside of bolt carrier (bottom of hole where bolt firing pin tube passes thru) from shooting dirty ammo in overlubed bolt/carrier?

          Comment

          • #6
            slo5oh
            Senior Member
            • May 2005
            • 730

            1) Oil?
            2) Try cleaning bcg, ch and inside upper of all oil then work the upper, as if you are manually loading a round, a hundred times or so. Then clean and oil it back up (someone else recommended this here on cgn)
            3) Remove and reinstall your buffer and spring.
            Also, you are running all standard parts? No heavy spring or buffer I hope.
            Last edited by slo5oh; 08-16-2013, 5:12 PM.

            Comment

            • #7
              gsguns
              Junior Member
              • Nov 2012
              • 21

              CC Gunsmithing in Redwood City Chaz is awesome, look him up on Yelp

              Comment

              • #8
                POLICESTATE
                I need a LIFE!!
                • Apr 2009
                • 18185

                I'd check magazines and ammo first.

                What are you using?
                -POLICESTATE,
                In the name of the State, and of the School, and of the Infallible Science


                sigpic


                Government Official Lies
                . F r e e d o m . D i e s .

                Comment

                • #9
                  jasonnorcal
                  Senior Member
                  • Mar 2009
                  • 1297

                  1. Oil, don't be afraid to use alot
                  2. Ammo, good brass cased ammo

                  3. Gas system
                  Homer Simpson gun safety: "This is the trigger, and THIS is the part you point at whatever you want to die..."

                  Originally posted by Chuntsman949
                  does it come with a flat billed hat, and a spade shirt?

                  Comment

                  • #10
                    Puuloa
                    Member
                    • May 2011
                    • 224

                    Check the gas tube by blowing air from the front of barrel to see if bolt carrier goes back.
                    82-85 5th Marines, 85-88 3rd Marines,
                    88-89 Kaneohe Marine Corps Air Station Rifle Range,
                    Marksmanship Instructor.

                    Comment

                    • #11
                      motorwerks
                      Senior Member
                      • Nov 2008
                      • 1619

                      I'd start with the easy stuff, pull the bolt carrier group. If you extend the bolt forward can you place the BCG on the bolt with the carrier sticking straight up with the bolt staying extended? If you can you're golden, if not replace the Rings. While its out make sure the gaps in the gas rings are NOT lined up in a row.

                      Also while the BCG is out I'd push on the gas tube (from the rear towards the front) to rule out that the gas blocks SUPER loose (I wasn't sure if it was a low profile gasblock under the free float)

                      Magazines, try them in the other AR, that may or may not help rule them out but at least if you throw 100 (or however many rounds you feel safe with) down range you can semi rule that out.

                      Are you running steel cased ammo? Some AR's will eat it some wont.

                      Did you change ammo? Something could have changed at the manufacture, I'd try a different batch.

                      To be honest to me it sounds like a magazine problem. It almost sounds like the Magazine isn't getting the round up far enough fast enough.

                      Lube the snot out of it. I've never seen one stop because it was too wet, but I've seen problems with them too dry.

                      Maybe have a friend go with you and stand off to the right and back a little (in a safe place behind the 180*) to watch and see if its short stroking.

                      I'd like to know what:
                      Any mods to the trigger/hammer
                      Ammo
                      Magazines

                      Comment

                      Working...
                      UA-8071174-1