Has anyone here ever filed a bevel into the face of the bolt lug opposite the extractor? Armalite machines their bolts with that particular bolt lug a lower profile than the rest. Supposedly, the symmetry of the bolt face in this condition helps distribute wear throughout the lugs and reduces a chance of a bolt lug cracking. Without this modification, the bolt would bear force at all lugs save the non existent lug position where the extractor is. It seems as if the lugs adjacent to the extractor would in turn bear more force in compensation.
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Ar15 Bolt Modification
Collapse
X
-
Ar15 Bolt Modification
Tags: None -
This is why I'm wondering if anyone here has actually done such a mod. If not, I just may buy an extra bolt and test this theory.Comment
-
The issue is that there are only 7 lugs bearing on the extension.
When you press against the bolt with the cartridge enough for all the lugs to start flexing, the bolt lays over towards the extractor because of the imbalance in strenth of the lugs.
When the bolt starts to lay over, the two lugs outside of the extractor take much more of the force as all the other lugs are basically pivoting on those two lugs.
That's why those lugs break first.
Removing the lug opposite the extractor causes the load to be balanced on all 6 remaining lugs.Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
Spot On regarding balancing the load. This was an issue that was already well known by Stoner and Sullivan but it wasn't an issue with the original .222 Special round (precursor to the 5.56x45). Later on with the development of the 5.56x45 and the higher chamber pressures and higher cyclic rate there were no long term durability studies done, though everything seemed to function OK. The assymetrical lug loading became an issue with the M4 and then more pronouced with rifles chambered in 7.62x39, 6.5 Grendal, 6.8SPC and others with increased bolt thrust. While relieving the opposite lug does even out the lug loading, it does reduce the lug contact by approximately 14% and thereby increasing the load on the remaining six.The issue is that there are only 7 lugs bearing on the extension.
When you press against the bolt with the cartridge enough for all the lugs to start flexing, the bolt lays over towards the extractor because of the imbalance in strenth of the lugs.
When the bolt starts to lay over, the two lugs outside of the extractor take much more of the force as all the other lugs are basically pivoting on those two lugs.
That's why those lugs break first.
Removing the lug opposite the extractor causes the load to be balanced on all 6 remaining lugs.
six of one, half-dozen of the other......Luck favors the prepared.
The original battle plan did not survive initial contact with the enemy.
"The things that will destroy America are prosperity at any price, peace at any price, safety first instead of duty first, the love of soft living and the get rich quick theory of life." -Theodore RooseveltComment
-
Not knowing more about this has always bothered me.
Sevel times, I have considered taking two bolts from the same batch, modifying one of them and then destructively testing them to see what the pressure would be on the press ram when they yield...Last edited by ar15barrels; 05-26-2008, 12:58 PM.Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
So, what's stopping you?

Seriously though, a lot of people can benefit from the results. Part of me thinks this would be a cool concept to prove, but another feels it may be a solution in search of a real problem.Comment
-
Good point. However, the benefit that I'm ideally looking for differs just a bit.
What is the theoretical (and perhaps actual) extension of lifespan of the modified bolt based on round count? There are many bolts out there that are unmodified and perform flawlessly for 10-30K of rounds. If just this simple mod can increase bolt lifespan without any drawbacks, it is worth the two minutes and several thousandths of metal removed. However, as with anything unproved and different from original engineering, one must rationally question both the effectiveness and overall result of system integrity in such a modification. Also, is it just marketing hype that some "improved" bolts are made this way from large manufacturers?Comment
-
Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
-
Bolts commonly fail in two ways, the two lugs outbound of the extractor yield from excess pressure/thrust or the bolt breaks across the cam pin hole from poor heat treating.

Breaking across the cam pin hole is mostly a Bushmaster problem as we don't see this in other brands of bolts.Randall Rausch
AR work: www.ar15barrels.com
Handguns: www.handgunbarrels.com
Bolt actions: www.700barrels.com
Foreign Semi Autos: www.akbarrels.com
Most work done while you wait on a scheduled shop visit.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,958
Posts: 25,177,876
Members: 358,862
Active Members: 5,392
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 33503 users online. 114 members and 33389 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.



Comment