Unconfigured Ad Widget

Collapse

bartlein

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Vepr62
    Senior Member
    • Oct 2006
    • 1216

    bartlein

    I am collecting parts for a .338 LM built and was looking at Bartlein barrels. They have barrels with 6 grooves and 5R grooves. Which one would be better precession wise for 250-300 grain bullets? What would be the best muzzle break to tame the beast? So far I have AICS 1.5 tan stock, waiting on a Stiller action from group buy, and need a barrel/ muzzle break. Randy @ R&D doesn't take new work untill the end of summer, so who else could you reccomend to put this together? Thanks.
    Vasiliy
  • #2
    ar15barrels
    I need a LIFE!!
    • Jan 2006
    • 57202

    Go with the 5r rifling profile.
    It's gentler on the bullets leading to more consistent obturation.

    JP recoil eliminator or an Armalite tank brake.
    Randall Rausch

    AR work: www.ar15barrels.com
    Handguns: www.handgunbarrels.com
    Bolt actions: www.700barrels.com
    Foreign Semi Autos: www.akbarrels.com
    Most work done while you wait on a scheduled shop visit.

    Comment

    • #3
      wildcard
      Veteran Member
      • Aug 2006
      • 4928

      Not sure if 6 grooves will offfer anything extra. I'd get Bartlein on the phone and figure it out.

      You do realize that putting the TAC338 in the AICS will require some custom work, right?

      Comment

      • #4
        Vepr62
        Senior Member
        • Oct 2006
        • 1216

        B

        Thanks, gentlemen. I know about stock mods. Any more opinions?
        Vasiliy

        Comment

        • #5
          rksimple
          Calguns Addict
          • Jan 2006
          • 6257

          Get the 5r style. I have a bartlein on my R+D build and its fantastic. The 5r is about the standard now for good accuracy and good velocity. How much of it is hype? I don't know. All I know is that it shoots.

          As for the brake, in addition to those mentioned, check the Badger FTE.
          GAP Team Shooter 5

          Comment

          • #6
            C.G.
            Calguns Addict
            • Oct 2005
            • 8259

            If you want to shoot 300 grainers make sure you get at least 1 in 10 (or 1 in 9) twist. Slower twists do not take the 300s very well.
            sigpic

            Comment

            • #7
              Timberwolf
              Calguns Addict
              • Oct 2004
              • 6275

              Get the 5R and wait on Randy for the build, I'm waiting too so take a number
              I'm only smiling at you while you talk to me because it's hilarious that you really think I give a crap about you.

              As I've gotten older I thought I was gaining patience, then I realized I simply don't give a crap.

              Comment

              • #8
                wildcard
                Veteran Member
                • Aug 2006
                • 4928

                Originally posted by Timberwolf
                Get the 5R and wait on Randy for the build, I'm waiting too so take a number
                I squeezed in a TAC338 build on a AICS 2.0 and a Rock barrel. Suckers!

                Comment

                • #9
                  Vepr62
                  Senior Member
                  • Oct 2006
                  • 1216

                  Thank you. I'll get 5R, 1in10 Bertlain MTU contour, 26". And I will wait for R&D to get it built. I think we should support CA businessess, especially gun related.
                  Vasiliy

                  Comment

                  • #10
                    Fjold
                    I need a LIFE!!
                    • Oct 2005
                    • 23094

                    If you get a choice always take the barrel with an odd number of grooves.

                    In a barrel with an even number of grooves, the lands are directly across from each other which results in more distortion of the bullet. In a 308 caliber barrel the bullet gets squeezed down from .308 to .300 diameter between the lands.

                    In a barrel with an odd number of grooves the land on one side of the barrel is directly across from a groove on the other side so the 308 bullet only gets compressed down to .304 in diameter. This should result in less compressive force on the bullet which means less distortion and less pressure required to push the bullet down the bore.

                    My two long range built guns carry 5 groove and 3 groove barrels.
                    Frank

                    One rifle, one planet, Holland's 375




                    Life Member NRA, CRPA and SAF

                    Comment

                    • #11
                      Timberwolf
                      Calguns Addict
                      • Oct 2004
                      • 6275

                      Originally posted by wildcard
                      I squeezed in a TAC338 build on a AICS 2.0 and a Rock barrel. Suckers!
                      You are a dog - and since I may have to now wait longer because of said bump I think I should get at least a round or two through the finished product. I love driving 338s
                      I'm only smiling at you while you talk to me because it's hilarious that you really think I give a crap about you.

                      As I've gotten older I thought I was gaining patience, then I realized I simply don't give a crap.

                      Comment

                      • #12
                        C.G.
                        Calguns Addict
                        • Oct 2005
                        • 8259

                        Originally posted by Vepr62
                        Thank you. I'll get 5R, 1in10 Bertlain MTU contour, 26". And I will wait for R&D to get it built. I think we should support CA businessess, especially gun related.
                        Vasiliy
                        If you want to go long distance you may want to think about 29" barrel.
                        sigpic

                        Comment

                        • #13
                          wildcard
                          Veteran Member
                          • Aug 2006
                          • 4928

                          Originally posted by C.G.
                          If you want to go long distance you may want to think about 29" barrel.
                          There's actually very liitle to be gained from a 29" barrel vs 26" given the 3" tradeoff. 27" is generally the longest you want to go as the gains after that aren't much for the .338 Lapua.

                          Comment

                          Working...
                          UA-8071174-1