Unconfigured Ad Widget

Collapse

AR 15 Wylde problems FIXED

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 121ahc
    Junior Member
    • Jan 2013
    • 73

    AR 15 Wylde problems FIXED

    Last edited by 121ahc; 05-15-2013, 1:06 PM.
  • #2
    Yerman
    Senior Member
    • Aug 2011
    • 1396

    Have you tried contacting the manufacturer?

    Comment

    • #3
      121ahc
      Junior Member
      • Jan 2013
      • 73

      They aren't answering the phone these days like everybody else.

      Comment

      • #4
        Cnynrat
        Senior Member
        • Dec 2008
        • 2221

        I doubt that the problem is with the Wylde chambering per se.

        I have an AR with a barrel chambered in Wylde (Superior Barrel's 18" "Terabratus") and it shoots great. Haven't had a single FTF/FTE with over 1000 rounds through it.

        More likely you have another problem with the barrel or ???
        Last edited by Cnynrat; 04-19-2013, 2:07 PM.
        Dave

        Lifetime Member, Second Amendment Foundation

        Comment

        • #5
          121ahc
          Junior Member
          • Jan 2013
          • 73

          Loaded round ejection?

          Do you have any problem ejecting a loaded round from your Wylde barrel?

          Comment

          • #6
            Cnynrat
            Senior Member
            • Dec 2008
            • 2221

            Originally posted by 121ahc
            Do you have any problem ejecting a loaded round from your Wylde barrel?
            Not something I do all that often, but no, I've never had a problem with that either with the gun hot or cold.
            Dave

            Lifetime Member, Second Amendment Foundation

            Comment

            • #7
              GreenAndy
              Member
              • Sep 2009
              • 496

              ArmaLite uses the Wylde chamber and I've never had a problem with it being tight, not ejecting, or getting stuck. Hot to cold it shoots and functions great.

              Maybe do a chamber cast? Get the exact dimensions your rifle was built to. Sounds like a tight chamber.
              You only live twice. Once when you are born and once when you look death in the face.

              IAN FLEMING

              Comment

              • #8
                chicoredneck
                Veteran Member
                • Jul 2010
                • 2904

                If it functions flawlessly after the barrel warms up, something is expanding causing more gas to flow. My gues is that your gas block is either mis-aligned, or the port is undersized.

                I highly doubt the problem is with the chamber, but you can buy some go and no-go guages fairly cheap to check your chamber dimensions.

                Comment

                • #9
                  121ahc
                  Junior Member
                  • Jan 2013
                  • 73

                  I have changed the gas block twice and adjusted and aligned it more time than I can count. Does anybody have the gas port hole size for a mid barrel .750, 16 inch long barrel for me to check my gas port hole.

                  Comment

                  • #10
                    chicoredneck
                    Veteran Member
                    • Jul 2010
                    • 2904

                    Gas port size can range between .068 to .085 for a 16" barrel.

                    Comment

                    • #11
                      6mmintl
                      Veteran Member
                      • Apr 2008
                      • 4822

                      Are you using SMALL BASE DIES? the Wilde chamber is a match chamber designed primarily for using heavy 77-90 grain bullets and has been thru minor changes since concept/inception around 1984 when the A2's came out.

                      It was designed primarily for the Canadian service rifle teams.

                      Std. dies (larger base dia.) may be problematic in a dirty chamber and your hot barrel shooting indicates your shooting a lot of rounds fast without chamber cleaning.

                      With a M4 configuration your wasting a good barrel/chamber on a double tap gun that will not function well, 20" or longer is the design parameters for the chamber/ match loads.

                      Ball/commercial ammo varies too much dimensionally and its a handload proposition to wring out the best the chamber and heavy bullets have to offer.

                      Comment

                      • #12
                        kendog4570
                        Calguns Addict
                        • Dec 2008
                        • 5180

                        The Wylde chamber is actually larger than 5.56 NATO in all areas except the throat diameter, throat length, and headspace dimension. The latter is the same for all 223 class cartridges. My 2007 Wylde drawing dates from 1984 with no revisions.
                        Small base dies were introduced by the reloading companies to ease functioning in commercial autoloaders like the Remington 740 series, Browning BAR, and Winchester 100, which had anemic operating systems when compared to military service rifles. It is doubtful they are any help in properly chambered and head spaced guns like AR, M1, M14, FAL, FN49, etc.
                        Last edited by kendog4570; 04-19-2013, 11:49 PM.

                        Comment

                        • #13
                          kendog4570
                          Calguns Addict
                          • Dec 2008
                          • 5180

                          Originally posted by 121ahc
                          Barrel: GTS Recon II 1/7 Stainless Steel Mid gas system 16 inch

                          Gun only feeds and ejects properly when the barrel warms up. As soon as it cools down it starts to short cycle no matter what kind of ammo it is fed. It’s a new build. I have been building AR’s for 25 years and this is my first Wylde build. I have eliminated every possible problem except the chamber or gas port hole size. I have reached a point where I am ready to have it re-chambered in 5.56. I have changed out every part short of the stripped upper receiver with the stripped barrel screwed into it. Could somebody give me the correct gas port hole size for this barrel? When the barrel is too hot to touch the gun functions flawlessly. Cool down a little and it’s a single shot. I have 300 rounds through it now. Ejecting an unfired round from the chamber is all but impossible. Once chambed it’s stuck until you fire it. I have read that this is not unusual for a Wylde chamber. Anybody else have any experience getting a Wylde to chamber and eject properly?
                          Changing to 5.56 will accomplish nothing. For all intents and purposes it IS a 5.56. Besides, you can't put throat back in it!
                          Start with the simple stuff first. What ammo are you using? You should be able to clear a live round easily. That's a red flag right there. Check CARTRIDGE headspace. If the ammo passes that test, check the gun headspace. Too tight headspace on a gas gun is more dangerous than too much headspace. It's highly unlikely that the chamber is too tight or short, but there are so many boutique suppliers and "manufacturers" these days that anything is possible.
                          Last edited by kendog4570; 04-19-2013, 11:47 PM.

                          Comment

                          • #14
                            121ahc
                            Junior Member
                            • Jan 2013
                            • 73

                            I'm have only shot factory 223 and 556 through it of various manufactures. It has all been 55gr bullets. I don't shoot reloads. I did borrow two 62gr bullets at the range and they did fire and eject fine.

                            Ejected rounds have a ring around the throat area on the bullet showing they are being compressed against the throat of the chamber. Is this normal?
                            Last edited by 121ahc; 04-20-2013, 10:10 AM.

                            Comment

                            • #15
                              chicoredneck
                              Veteran Member
                              • Jul 2010
                              • 2904

                              Originally posted by 121ahc
                              I'm have only shot factory 223 and 556 through it of various manufactures. It has all been 55gr bullets. I don't shoot reloads. I did borrow two 62gr bullets at the range and they did fire and eject fine.

                              Ejected rounds have a ring around the throat area on the bullet showing they are being compressed against the throat of the chamber. Is this normal?
                              I would have to see a picture, but if the ring you describe is just black powder fouling it is simply being caused by the round extracting prior to the case fully sealing in the chamber. This is not all that unusual and can be caused by a number of factors including, low pressure ammuniton, over sized chamber or bore resulting in lower pressures, or powder that is not timed well with your gun causing the cartridge to be extracted while still under high pressure. Powder fouling of the neck and shoulder area of a cartridge is not necesarrily indicative of a malfunctioning or out-of-spec gun.

                              If the rifle functions properly with 62gr 5.56 pressure ammo, the problem is most likely an undersized gas port or one that was purposefully sized to function with 62gr NATO and deliver softer recoil.

                              You may also have a gas ring that is not sealing fully. When it warms up it expands and creates a better seal, but my money is on an undersized gas port, especially if some ammo functions fine in your rifle.
                              Last edited by chicoredneck; 04-20-2013, 10:27 AM.

                              Comment

                              Working...
                              UA-8071174-1