Unconfigured Ad Widget

Collapse

1911 barrel fitting problem.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • dangerranger
    Senior Member
    • Jun 2010
    • 578

    1911 barrel fitting problem.

    I'm building a 1911 for my youngest son. Sometime in the past I got a Match barrel and bushing that I had set aside for use later. Well now is the time.I have fitted the link and feet, and then the hood area. I ended up with a nice tight fit. But when I tried to install the slide assembly on to the frame, I cant pull the slide back all the way. The inside of the slide is hitting the top of the barrel about mid chamber. So my question is, Do I need to sand the top of the barrel to gain this clearance? I have no instructions with the barrel, and am not even sure who made it. I found online several instructions for fitting the hood and legs but none that address the fitment problem I'm having. In the past Ive used drop in barrels and some have a sanded appearance in this same area. So what do you all think? Thanks DR
  • #2
    Gunsmith Dan
    Senior Member
    • Apr 2012
    • 1445

    Sounds like a link issue to me, double check the new link and compare it to the old link. See if they are the same length and the holes are the same diameter.

    Comment

    • #3
      kendog4570
      Calguns Addict
      • Dec 2008
      • 5180

      You have some measuring to do. Lug depths, both barrel and slide, and figuring out min/max lug engagement, as well as other important clearances. Could be as simple as a link, or a lot more involved. Kunhausen's book has a rather long-winded explanation of barrel fitting.

      Comment

      • #4
        dangerranger
        Senior Member
        • Jun 2010
        • 578

        I'm thinking the link is correct, Because ... When the slide is pulled to the rear the barrel drops out of the locking lugs and stops just touching the frame above the feed ramp. So my two choices are going to be remove material from the bottom of the barrel But I'm afraid that will affect the barrel being centered on the firing pin. Or removing from the top of the barrel. I don"t have Jerry Kunhausen's Book and none of the books I have here make any mention of needing to make any adjustment to this area. I may have to get a copy of Jerry's book. I'm sure its easier to remove material than to put it back on. DR

        Comment

        • #5
          Ledbetter
          Senior Member
          • Sep 2002
          • 557

          Brownells sells a kit with different sized links so you can find the size that fits best. Don'grind your slide or frame.
          Winchester Canyon Gun Club -- Life Member
          N.R.A. -- Life Member
          Santa Barbara County CGF Sponsor

          Comment

          • #6
            Ledbetter
            Senior Member
            • Sep 2002
            • 557

            Brownells sells a kit with different sized links so you can find the size that fits best. Don'grind your slide or frame.
            Winchester Canyon Gun Club -- Life Member
            N.R.A. -- Life Member
            Santa Barbara County CGF Sponsor

            Comment

            • #7
              Mikeb
              Veteran Member
              • May 2008
              • 3189

              seems to me there is something about releaving the bushing to allow the tilt of the barrel. When in doubt work on the cheapest part. +1 for Kuhnhousen

              Comment

              • #8
                dangerranger
                Senior Member
                • Jun 2010
                • 578

                Ive Got It! I covered the barrel in Dyekem [ Purple lay out dye] and put it all together and found that there was a high spot on the inside of the slide. So with a little sanding and polishing it now moves freely. And the firing pin is still centered. I still may need to sand a little to gain the needed clearance, But that will only be a tiny amount. Thanks DR

                Comment

                Working...
                UA-8071174-1