Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
I read 69Mach1's tutorial....
Collapse
X
-
kcstott, while pimp, pic #2 is a PSL I believe, not an AK.
Quick glance at me kits this weekend tell me that A) I have a Bulgarian Arsenal stamped kit and B) Atlantic provided completely demilled kits for my Polish underfolder and the Bulgarian. Which is great because after reading that demilling how-to, I was dreading this task. As an added bonus the Bulgarian looks unissued!
Now for another question. Since I am thinking about having a gunsmith prep the barrel (headspace, FSB install, etc.), is this this one okay?
Getting ready to start ordering parts, so excited!Comment
-
Here is my unintelligent question of the day:
Of the Dremel tools listed by 69Mach in his thread: diamond bit, drum grinder and cutting wheel - which exact versions to I need to buy since there are many options available online and are confusing the heck outta me.
Also I have seen another tool to enlarge the rivet holes that didn't line properly with the receiver. If someone can let me know which tool that is that'd be awesome.

Also of the various Dremel models available, which one would be the most suitable for build projects?Comment
-
Get and EZ406 starter kit. it's $13 at Lowes. then add a couple of sanding drum arbors and a few sanding drums. Get course and med drums as you will need to either remove a lot of metal fast or just do a touch up. I say get a couple of arbors as you can have both grits ready to go with just a tool change. The diamond bit is a small diameter one like 1/8 or 5/64 diameter. All of this stuff my be had in a $30 starter kit or if you buy the Dremal as a starter kit it may have the stuff you need in it already
I will make a suggestion out of pure convenience. Get the flex shaft attachment. This allows you to get the motor away from you and your body keeping you from blocking the vents and burning up the motor. The flex shaft body is also smaller and can get into areas where a Dremal motor can't and you're not holding a 2 pound electric motor all day long. My set up at home is the Dremal hangs from the rafter in the garage on a tool balancer and the flex shaft is clipped to it. I just reach up grab the hand piece turn on the motor and go. I don't have crap cluttering up my bench.
I used the 200 series for years. and then it burned out I set it off the dremal for repair they sent back a brand new tool free of charge and it was upgraded.
Get the best one you can afford. I have no problem spending lots of money on good tools. It's like an addiction
And FWIW I've only owned two Dremals in 30 years and I'm still using my second one that's how long they last.Comment
-
Thank you, Kerry.Comment
-
Pulling together my parts list, how does one decide if you need a 1mm or a 1.5mm center support? Again, this is for a Polish UF kit and a Bulgarian fixed stock. Using ak-builder flats; Polish and a standard B1-71, respectively.
Figure the FCG pin retaining plate isn't a bad investment at $5, any reason not to get these?
Any rivets better than others?Comment
-
1mm or 1.5mm center support depends on your flat. Polish UF I believe uses 1mm flat. And get the retaining platePulling together my parts list, how does one decide if you need a 1mm or a 1.5mm center support? Again, this is for a Polish UF kit and a Bulgarian fixed stock. Using ak-builder flats; Polish and a standard B1-71, respectively.
Figure the FCG pin retaining plate isn't a bad investment at $5, any reason not to get these?
Any rivets better than others?Without HIM, we cannot. Without us, HE will not.
Originally posted by sirslothThat's just the way of the world, man. It's called the hook up. If you work at McDonald's you get free fries. Starbucks employees get free coffee. Cops, well you get the idea...Originally posted by cdtx2001BTW y'all remember, for every AR lower that's finished a Liberal sheds a tear.Comment
-
Confirm the caliber on your Bulgarian. The B1-71 is for 7.62. In the event that you need a 5.45, than you would need B2-41. When your on the page with the specific flat, about mid-page you will find the recommended center support and rivet set. Also, +1 on getting the retaining plate.Comment
-
Yep you got the 1mm flat so you'll need the center support for 1mm receivers. The redstar retaining plate is IMO a necessity. I believe the Polish UF rivet set will be ok for your Bulgy rear trunnion. This is assuming that you're using the forked ak74 trunnion.sigpicOriginally posted by Dr. ElkyIf your a man who wears white sunglasses, your probably a douche bagOriginally posted by CSACANNONEERI've been know to cross dress and go the other way at certain events.Comment
-
It is a Bulgarian, Arsenal marked ak47, not a 74, kit. And Curtis did ask if it was a 47, so the B1-71 is the right one. I have been sweating whether I bought the right parts kit or not so I checked my invoice and it is indeed 7.62x39. I do NOT need another caliber. But I don't have a Bulgarian so figured this would be a great way to learn more about how the AK is made/ functions and get something different.
Is Polish tantal the UF flat?nm, like caiman said, all the info is on the flat page just had to read.
I wish I had waited a little bit and got the ak-builder UF kits with the barrels installed. That part looks like a PITA. Guess I could always get one more....
Since ak-builders are out of barrels does anyone know about Atlantic Firearms US made barrels?
The retaining plate(s) are on the wishlist.
Thanks for all the help guys. Now it's just a matter of ordering and finding a build party. Wheeeeeee!Last edited by mike_the_wino; 05-11-2012, 11:07 AM.Comment
Calguns.net Statistics
Collapse
Topics: 1,870,884
Posts: 25,177,121
Members: 358,862
Active Members: 5,395
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 33741 users online. 40 members and 33701 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.


Comment