Unconfigured Ad Widget

Collapse

Help with inserting PSL barrel

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jwarren116
    Junior Member
    • Dec 2008
    • 52

    Help with inserting PSL barrel

    So, I'm trying to put together a PSL parts kit that I picked up. Everything has been going just fine until now. I'm trying to get the barrel into the front trunion. I have a 12-ton harbor freight press, but I was having trouble with making a jig, so decided I'd go with the "allthread" method. I have a 36" section of 1/4"-20 with 3 brass washers on the muzzle break end with a nut. On the trunion end I'm using the bolt carrier instead of a jig. The threaded rod goes through to the back with 3 brass washers and double nuts tightened to all end against each other.

    The barrel is having a bit of a tough time going in. It's "jumping" as the nuts are tightened, rather than moving smoothly. I cleaned up both pieces really well before putting them together, no burrs, snags, nothing. I was advised by a friend to use lithium grease instead of anti-seize. I'm wondering if that was my first mistake. So, the barrel is right to the point where the RSB is meeting the trunion, and it's very slightly canted to one side. I've tried everything I can think of and I cannot seem to straighten it. I put the receiver in a vice and tried like all hell to straighten that barrel with a wrench, but it wouldn't budge. I tried tapping with a hammer, nothing. I even tried twisting it while I tightened the allthread to see if I could get it to jump sideways a bit.

    I need advice! Am I best suited to press the barrel out and start over with anti seize, and maybe a bit more smoothing of the shank?? Or will it straighten out itself as the barrel goes in the rest of the way? It's BARELY touching on the left side, with just over 1/16" on the right side. (Sorry for the horrible cell phone picture, it's all I had available)

  • #2
    Gowking
    Veteran Member
    • Mar 2008
    • 2664

    Have you measured the barrel diameter and the diameter of the trunnion to see if the press fit is correct? You want a .001" press fit for the 23mm barrel. I would take the barrel out and measure, if it's within specs try using anti-sieze. It has always worked for me. Also make sure the rear sight block is lined up straight before pulling the barrel in too far. If you need to remove some material be careful about it and check the diameter of the barrel at different locations around the OD as you take material off.

    -MRA
    Last edited by Gowking; 08-25-2011, 12:18 AM.

    Comment

    • #3
      69Mach1
      Super Moderator
      CGN Contributor - Lifetime
      • Jan 2006
      • 15032

      Are you sure it's not hitting a rivet from the inside? And do as MadRiverArms suggests. It may be too tight.
      sigpic
      69Mach1
      munkeeboi
      TURBOELKY
      antix2
      WTSGDYBBR
      tujungatoes
      jmpgnr24K

      Comment

      • #4
        Gowking
        Veteran Member
        • Mar 2008
        • 2664

        Yeah I should have added to take a picture of any scratching/galling that you find when you remove the barrel.

        -MRA

        Comment

        • #5
          nicitaja
          Member
          • Apr 2005
          • 315

          what everyone else said, remove it and measure three times.

          Since it could be too large (over .001") I'll point you to some answers. If your too large, a lathe is the best option, but look up fredieusa's virgin yugo build, the sand paper disc on a hand held drill works, if your more than .004 I'd try to find a lathe, but his method has been used by many of us.

          Also, what MadRiversArms said, the barrel is gonna show some scratching/galling that will be answer to your questions.

          I can offer one other suggestion as well, it will cost you about 8 bucks, but change from 1/4-20 to 1/4-28, the finer threads actually make a big difference in moving the barrel in smaller increments.

          -John

          Comment

          • #6
            jwarren116
            Junior Member
            • Dec 2008
            • 52

            Thanks for the replies.

            It is a matching kit, so I figured it was sized right. There was minor scratching/galling on the top of the barrel shank when I got it. I hit it with a touch of 400 to knock down the ridges and help with insertion. But I suppose it needs more. I'll see if I can press the barrel out today and start over. Any secrets to getting the barrel out with the trunion in the receiver? I'm at work today, so I can't look at it now, but if I remember it might be tough to press out.

            Comment

            • #7
              nicitaja
              Member
              • Apr 2005
              • 315

              I have one of the barrel press tools, it makes it easy to push it out when the trunnion is in the barrel. see -> http://www.calguns.net/calgunforum/s...d.php?t=455825 for ideas, I made my own, and managed to get one of the ones I was looking for. A hardend shaft from tool steel welded to some angle steel and gap to go around the rear trunnion, and then a socket weled into the angle iron is how I made mine, again, read the post, its makes it a lot easier.

              -John

              Comment

              • #8
                generalpetres
                Senior Member
                • Sep 2009
                • 787

                lithium grease will be to thick to help get the barrel in the trunnion, your best bet would be anti seize. after you remove the barrel and get everything ready to be pressed in again use a set of feeler gauges to help you get the rear sight block positioned evenly in the trunnion. hopefully you get everything worked out ok.
                NRA Member

                Comment

                Working...
                UA-8071174-1