Unconfigured Ad Widget

Collapse

Rivet Check

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Flat Broke
    Member
    • Mar 2008
    • 435

    Rivet Check

    Almost a year ago, I had done the rivets in the front trunion of my first AK build. The project stalled when other things moved into focus, and a couple days ago I pulled the dusty bag of parts down, cleaned everything up and decided to get the rifle finished up. I went with the bolt cutter rivet crushers with a small bucking bar to smash the rivets and just wanted to get a 2nd opnion on them before I pull the barrel back into the trunion.

    Here are some pics. You can click on the link to get to a bigger version of the pic.













    They're not the prettiest things on the planet, but I just want to make sure they're strong enough. For reference, they are Arsenal rivets. Don't mind the open hole on the left side of the trunion, that will be covered by the apropriate bullet guide.

    Any input or concern is welcome as I just want to make sure everything is safe before I proceed.

    On a separate note, if I wanted to park the receiver prior to inserting the barrel (the barell is already parked and painted), do I need to protect the barrel interface area on the trunion?

    Thanks,
    Chris
    Last edited by Flat Broke; 09-30-2009, 6:09 PM.
    "We will always remember. We will always be proud. We will always be prepared, so we may always be free." - Ronald Reagan, June 6th 1984
  • #2
    CSACANNONEER
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2006
    • 44094

    They are perfect! Who cares about looks anyways? After all, it's just an AK. It'll work perfectly. If you need help or tooling, contact me about attending my build party on United Nations Day (Oct. 24th) weekend.
    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
    California DOJ Certified Fingerprint Roller
    Ventura County approved CCW Instructor
    Utah CCW Instructor


    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

    sigpic
    CCW SAFE MEMBERSHIPS HERE

    KM6WLV

    Comment

    • #3
      Flat Broke
      Member
      • Mar 2008
      • 435

      Originally posted by fredieusa
      Other than appearance, they will work.

      If you have to, change out the two lower swell neck ones (accessible from the mag well). Dunno how deep the fractures go as they are crushed.. But an AK will hold up with less then the total 6 so no worries.

      I am no rivit champion myself, but that second pic is ugly..
      No worries on the comments on the second pic. Actually, the nick in the head of the rivit looks 1000x worse because of the flash. I could dress it with a file and you wouldn't know it's there. My main worry was just that they were squished enough etc. The lower ones look pretty worked, but the factures are superficial where I moved the crusher to hit it from a different angle. Even if you said they looked like piss and needed to be replaced, I'd be cool with that as I'm just looking for constructive input.

      Originally posted by CSACANNONEER
      They are perfect! Who cares about looks anyways? After all, it's just an AK. It'll work perfectly. If you need help or tooling, contact me about attending my build party on United Nations Day (Oct. 24th) weekend.
      I've gotta check my calendar, but I think I might be shooting you a PM. If nothing else, I could park my receiver and use a legitimate barrel press instead of threaded rod.

      Thanks to both of you for the input.

      Chris
      "We will always remember. We will always be proud. We will always be prepared, so we may always be free." - Ronald Reagan, June 6th 1984

      Comment

      • #4
        bigbob76
        Veteran Member
        • Dec 2007
        • 3954

        They don't look like they will interfere but I like to slide a straight edge in where the barrel slides in to confirm the rivets won't get hit by the barrel as it's installed. A little care looking for protruding rivets or gouges on the trunion or barrel can save a lot of grief at barrel installation time. Sometimes the original barrel installation or the later removal causes galling where there's material sticking up that has to be smoothed out. If it's not a smooth fit the barrel tends to move in jumps on installation and you end up having to go in and out trying yo get the hole lined up for the pin. I'm glad you are doing the build.
        If you can't explain it simply you don't understand it well enough. Albert Einstein

        Comment

        • #5
          Flat Broke
          Member
          • Mar 2008
          • 435

          Originally posted by bigbob76
          They don't look like they will interfere but I like to slide a straight edge in where the barrel slides in to confirm the rivets won't get hit by the barrel as it's installed. A little care looking for protruding rivets or gouges on the trunion or barrel can save a lot of grief at barrel installation time. Sometimes the original barrel installation or the later removal causes galling where there's material sticking up that has to be smoothed out. If it's not a smooth fit the barrel tends to move in jumps on installation and you end up having to go in and out trying yo get the hole lined up for the pin. I'm glad you are doing the build.
          That's the exact reason some of the rivets are a little "extra" squashed they're all clear of the I.D. of the barrel mounting area. Since we're talking about this, I removed my sight block to have some barrel work done. Because of this, I want to make sure I get the barrel in right the first time because otherwise it would be impossible for me to back it out with a gear puller in the same fashion when I demilled the trunion.

          With that in mind, does the threaded rod installation procedure afford greater precision in terms of slower and controlled movement of the barrel? I have see videos of barrels being pressed in, and it's not always a perfectly smooth operation.

          Thanks,
          Chris
          "We will always remember. We will always be proud. We will always be prepared, so we may always be free." - Ronald Reagan, June 6th 1984

          Comment

          • #6
            CSACANNONEER
            CGN/CGSSA Contributor - Lifetime
            CGN Contributor - Lifetime
            • Dec 2006
            • 44094

            I've pressed in a dozen or so barrels and, I think, I've only pressed one in too deep. It only takes a minute or so to press it back out though. If you need or want to press it in, either come to the BP or PM me and we can work out a time to meet.
            NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
            California DOJ Certified Fingerprint Roller
            Ventura County approved CCW Instructor
            Utah CCW Instructor


            Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

            sigpic
            CCW SAFE MEMBERSHIPS HERE

            KM6WLV

            Comment

            • #7
              sspen003
              Senior Member
              • May 2009
              • 1003

              Barrel Install: 3 pound sledge, block of wood, some grease, a beer and about 50 smacks with the sledge
              "The God of War hates those who hesitate."

              Comment

              • #8
                bigbob76
                Veteran Member
                • Dec 2007
                • 3954

                Originally posted by CSACANNONEER
                After all, it's just an AK. It'll work perfectly.
                If there are no burrs and the barrel is lubricated moving it in or out a little is usually pretty easy. I would say the problem I see most often is not getting the ears of the rear sight base centered but that doesn't seem to be a safety issue. If the hole in the trunion isn't lined up right with the hole in the barrel when you press the pin in the pin will shave off a little bit of the barrel. We're not doing brain surgery but I do remind myself we are preparing for repeated explosive events inches from our face. I look for some balance somewhere between complacency and paranoia. Like when a guys first build was a .308 pistol and he offered to let me shoot it first. I just told him I would prefer to watch. I used to be bullet proof and I would fly any airplane I could. Now I want to know a little bit about the airplanes I fly and I don't want to shoot somebody else's reloads unless I've seen how cautious they are.
                Last edited by bigbob76; 10-01-2009, 12:41 AM.
                If you can't explain it simply you don't understand it well enough. Albert Einstein

                Comment

                • #9
                  Flat Broke
                  Member
                  • Mar 2008
                  • 435

                  Originally posted by fredieusa
                  Sorry about my ugly comment Chris. It was not my intention to come across the way it sounds. Cheers.
                  No worries at all. Let's be real, pictures of the inside of the lower rivets should be put next to the definition of ugly rivet jobs

                  Chris
                  "We will always remember. We will always be proud. We will always be prepared, so we may always be free." - Ronald Reagan, June 6th 1984

                  Comment

                  • #10
                    rxdealer71
                    Junior Member
                    • Aug 2009
                    • 34

                    I've just gotten started riveting, and for the most part, the AK-builder Jig is worth splitting the cost with four guys. But the swell neck front trunnion rivets are the only ones that give me grief, the tend to bend over during the press and make ugly buttons or crooked top rivets. The rubber blocks sometimes start to give in at the first pressure and the receiver leans into the pressure point, causing this problem. Any suggestions for setting them up different?
                    RxDealer

                    "One can only hope that time is on our side, and not Diane Feinsteins."

                    Comment

                    • #11
                      bigbob76
                      Veteran Member
                      • Dec 2007
                      • 3954

                      Originally posted by rxdealer71
                      I've just gotten started riveting, and for the most part, the AK-builder Jig is worth splitting the cost with four guys. But the swell neck front trunnion rivets are the only ones that give me grief, the tend to bend over during the press and make ugly buttons or crooked top rivets. The rubber blocks sometimes start to give in at the first pressure and the receiver leans into the pressure point, causing this problem. Any suggestions for setting them up different?
                      I use the modified bolt cutters on those. An important thing is to countersink the holes for the swell necks. I use an old aircraft sheet metal trick of turning a large drill bit several times on the hole until there is a countersink. Then run the correct drill bit through it again to make sure the rivet sinks down in and is straight. If they don't come out just right on the inside I just clean them up with a Dremel for appearance.
                      If you can't explain it simply you don't understand it well enough. Albert Einstein

                      Comment

                      • #12
                        Utha Schleigle
                        Senior Member
                        • Oct 2007
                        • 593

                        They look good to me. Structurellly sound. I had to squish serveral times with rivits that had been cut with pointed ends. As soon I used flat ends or made flat ended my pancake heads came out purfect.

                        Make sure the factory round head is snugg to the reciver. Some say - if you can not get your finger nail under it passes. i like the razor blade or razor knife test.


                        razor knife can not get under head.


                        rivit trimmed with pointed end - not a good a good idea


                        result - had to adjust and many chomps to squish down



                        better results - flat top trimmed rivit with top left rough for good gripp.
                        Last edited by Utha Schleigle; 11-15-2009, 10:26 PM.
                        PLEASE WEAR EYE PROTECT & PROTECTIVE GEAR IN SHOP!!!!!! You can order another part from from manufacturer, but you can't order another finger or eye from your mother & father.

                        ***This DOES NOT constitute GOOD or SANE legal - professional gunsmithing - psychiatric MD - tax - accounting -gardening advice. Please contactact qualified a professional in their repective specialties.*** AWHHH go ahead and mix match specialities that could be funny!!!!!

                        Comment

                        • #13
                          Utha Schleigle
                          Senior Member
                          • Oct 2007
                          • 593

                          Will sand blast contact point of punches and squisher for better more positive gripp of rivit as it is squshed.


                          sand blast cone in shaper punch


                          will sand blast top end for trigger guard punches - for left and right rail reciever sides
                          PLEASE WEAR EYE PROTECT & PROTECTIVE GEAR IN SHOP!!!!!! You can order another part from from manufacturer, but you can't order another finger or eye from your mother & father.

                          ***This DOES NOT constitute GOOD or SANE legal - professional gunsmithing - psychiatric MD - tax - accounting -gardening advice. Please contactact qualified a professional in their repective specialties.*** AWHHH go ahead and mix match specialities that could be funny!!!!!

                          Comment

                          • #14
                            bigbob76
                            Veteran Member
                            • Dec 2007
                            • 3954




                            On aircraft this rivet would be a reject. I can't remember the reason given but when I was taught riveting in A&P school that ring around the formed head was called a smily face. Most aircraft rivets are aluminum and not hard to remove. We got a lot of practice removing smily faced rivets!
                            Last edited by bigbob76; 11-16-2009, 12:35 AM.
                            If you can't explain it simply you don't understand it well enough. Albert Einstein

                            Comment

                            • #15
                              Flat Broke
                              Member
                              • Mar 2008
                              • 435

                              Originally posted by bigbob76



                              On aircraft this rivet would be a reject. I can't remember the reason given but when I was taught riveting in A&P school that ring around the formed head was called a smily face. Most aircraft rivets are aluminum and not hard to remove. We got a lot of practice removing smily faced rivets!
                              I'm not an aerospace guy, but I'd guess that rivet would be a reject for risk of promoting a stress riser from it's sharp edge. Thank god we're workin on AKs and not Airframes eh?

                              Chris
                              "We will always remember. We will always be proud. We will always be prepared, so we may always be free." - Ronald Reagan, June 6th 1984

                              Comment

                              Working...
                              UA-8071174-1