Torque wrench choices

[Ravenslair]

I am looking at getting a torque wrench (inch pounds). I am looking at the following. I am curious what you all think and which you would recommend. Right now, I am planning on installing a scope and rings, although I would likely use it for other stuff later. Or, if there is another you would recommend (trying to stay $150 or less).

Thanks in advance.

Seekonk 1 to 75 inch pounds
Seekonk torque handles (would get 15in/lbs and 65in/lbs for the time being)
Magna-tip
Wheeler FAT wrench

[97F1504RAD]

I would buy this one

http://midwayusa.com/viewproduct/?productnumber=718023

[Bongos]

I'm in the same boat, I have a Seekonk 65 in lb T wrench which is good for rings to base, I still need a 18 lb for the ring screws, and 45-50 lb for the reciver to stock (Rem 700), as well as a 30lb for the base to reciever.
Currently looking at the Wheeler FAT and Mija....or individual Seekonks

[ar15barrels]

Get the Seekonks.
They are very good quality, USA made tools.

I have a Seekonk inch-lb torque wrench calibrator and I can tell you that the FAT wrenchs are not real accurate or repeatable from click to click.

[ar15barrels]

I'd also recommend you search ebay for USA made "torque screwdrivers" as there are a bunch of them floating around.

[Sig357]

I really like my Snap On torque wrench, pricey though. I purchased it for $200 when I was doing the engine on my Raptor.

[Ravenslair]

I'd also recommend you search ebay for USA made "torque screwdrivers" as there are a bunch of them floating around.

Lots to choose from. Thanks for the advice.

[motorhead]

depends on what other uses. screwdriver and t-handle are pretty worthless for auto work. a good inch clicker is suitable for most things and the best bargain. bearing preloads (rear axes, etc.) require a dial.

[KAVEMAN762]

I use a snap on torque wrench, I have the digital ones in 1/4"(inch lbs), 3/8" and 1/2" They all do angle torque, shows metric and standard, can convert to inch lbs and foot lbs., and couple other things. I mainly bought them to do motor builds and other auto hobby stuff. The angle torque works well for bottom end main cap bolts and others that need angle torque. But works really well for everything else also.

[Seesm]

Wheeler very common and works well.

[M. Sage]

I really like my Snap On torque wrench, pricey though. I purchased it for $200 when I was doing the engine on my Raptor.

Is that all?

I looove my Techwrench, but it's like $400. I loaned it to the other tech I work with, he bought one the next week! I see Kaveman is a fan, too.

[kortik]

Just for your information:

Borka Tools torque driver kit for firearms work

[kortik]

Borka Tools multi torque driver -12 fixed torque settings from 15 to 72 inch-lbs. Accuracy - +/-4%. Made in the U.S.A.
Weight of torque driver - 4 ounces, weight of driver with adapters and pouch (MG3) - 6 ounces, weight of complete kit
with accessories and pouch (MG3-SRA) - 14 ounces.
Size of pouched kit (MG3-SRA) - 6.5"x2.5"x1.25".

[kortik]

That's my thread, you bet.

Close to 300 of MG3s and MG3-SRAs were sold since June of 2010 just to guys in CA, either thru Sniper's Hide or directly by Borka Tools, and good number of NorCal Precision Rifle Club members got my stuff thru group buy arranged by Vu Pham, who now wants to run the second group buy.

If you have any questions, just ask.

[HUTCH 7.62]

SNAPON!that is all.....goodnight