Unconfigured Ad Widget

Collapse

Machining marks

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • pklin1297
    Veteran Member
    • Sep 2006
    • 3287

    Machining marks

    Hello all,

    Please take a look at the machining marks on this Limited-10 aluminum 2011 80% frame. Will I have to file/sand/stone these marks off, or will 120 grit AlOx blasting pretty much take care of these? The marks are smooth to the touch and I can't catch a nail on them. Thanks!













    By the way, for those who have build on this same railed frame, where do you guys put the Maker, Location, and Serial information?
    NRA Member, CAPRC Member
  • #2
    Limited-Ten
    Member
    • Dec 2012
    • 314

    10 mins with a scotch brite pad removes them all. They're pretty superficial.

    Comment

    • #3
      dwalker
      Veteran Member
      • Jul 2014
      • 2714

      Are you having it polished or coated? If polished/anozided they will buff out, if your coating it the beadblast will take care of it. I would not waste even a second (and I didnt) trying to clean them up.
      Fear is the spare change that will keep you broke

      Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

      Comment

      • #4
        Limited-Ten
        Member
        • Dec 2012
        • 314

        Also, if going cerakote blasting with garnet is pretty standard. Anodize should use a etch process too beforehand.

        The frame below was hit with scotch bright for 2 mins and thrown in a tumbler for a day with walnut and nu finish.


        Last edited by Limited-Ten; 10-28-2016, 9:55 PM.

        Comment

        • #5
          MosinVirus
          Happily Infected
          CGN Contributor
          • Sep 2013
          • 5282

          That long dustcover sure looks like a good place for a ID markings. Lol.

          Bottom of the dustcover would be a nice place, buts sides will do just fine I bet.
          Hobbies: bla, bla, bla... Bought a Mosin Nagant... Guns, Guns, Guns...

          Comment

          • #6
            pklin1297
            Veteran Member
            • Sep 2006
            • 3287

            I'll be filling the sides down to match width of slide, that's why I won't be etching the serial and other info there.
            NRA Member, CAPRC Member

            Comment

            • #7
              MosinVirus
              Happily Infected
              CGN Contributor
              • Sep 2013
              • 5282

              Understood.
              Hobbies: bla, bla, bla... Bought a Mosin Nagant... Guns, Guns, Guns...

              Comment

              • #8
                1flhtk4me
                Member
                • Dec 2013
                • 323

                Those are some rough tool marks.

                Guessing you would have to remove a couple of thousandths to get a decent surface finish.Be careful where the tolerances need to be close.

                Plating will not make the those surfaces smooth,the tool marks will still show.
                Last edited by 1flhtk4me; 10-29-2016, 7:51 AM.

                Comment

                • #9
                  1flhtk4me
                  Member
                  • Dec 2013
                  • 323

                  Originally posted by Limited-Ten
                  Anodize should use a etch process too beforehand.
                  Keep in mind etching will remove mat'l.

                  Comment

                  • #10
                    docflash
                    Member
                    • Jul 2010
                    • 235

                    Originally posted by pklin1297
                    Hello all,

                    Please take a look at the machining marks on this Limited-10 aluminum 2011 80% frame. Will I have to file/sand/stone these marks off, or will 120 grit AlOx blasting pretty much take care of these? The marks are smooth to the touch and I can't catch a nail on them. Thanks!

                    ===============


                    By the way, for those who have build on this same railed frame, where do you guys put the Maker, Location, and Serial information?
                    If California ends up following the BATFE regulations for manufacturer's marking requirements you will only need to put a serial number on the frame. Maker, city and state where made, model designations can all be on the slide.
                    The caliber is on the barrel hood.
                    Sig Sauer Certified Armorer, P-Series Pistols
                    Sig Sauer Certified Armorer, P320 Pistol

                    Comment

                    • #11
                      Limited-Ten
                      Member
                      • Dec 2012
                      • 314

                      Originally posted by 1flhtk4me
                      Keep in mind etching will remove mat'l.
                      Anodizing adds it back - for dimensional purposes it's usually a wash.

                      Only a few tenths need to come off. See the pictures I posted above, semi-reflective finish with with a few mins of scotchbrite and walnut tumbling.
                      Last edited by Limited-Ten; 10-29-2016, 12:06 PM.

                      Comment

                      • #12
                        dwalker
                        Veteran Member
                        • Jul 2014
                        • 2714

                        Originally posted by pklin1297
                        I'll be filling the sides down to match width of slide, that's why I won't be etching the serial and other info there.
                        My aluminum frame fit my Fusion slide perfectly without needing to do any filing.
                        Fear is the spare change that will keep you broke

                        Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

                        Comment

                        • #13
                          Limited-Ten
                          Member
                          • Dec 2012
                          • 314

                          Originally posted by dwalker
                          My aluminum frame fit my Fusion slide perfectly without needing to do any filing.
                          Slides come in different widths depending on mfg. we accommodate worse case scenario. Fusion uses STI width from what I've seen.

                          Comment

                          • #14
                            dwalker
                            Veteran Member
                            • Jul 2014
                            • 2714

                            Originally posted by 1flhtk4me
                            Those are some rough tool marks.

                            Guessing you would have to remove a couple of thousandths to get a decent surface finish.Be careful where the tolerances need to be close.

                            Plating will not make the those surfaces smooth,the tool marks will still show.

                            On my L10 frames- I have two aluminum ones and at some point need to order a steel railed, I have not had to really do anything like sanding etc. A simple polishing job starting with black or brown, then white, green, and finishing with red gave a pretty high polish suitable for anodizing or plating.
                            Fear is the spare change that will keep you broke

                            Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

                            Comment

                            • #15
                              dwalker
                              Veteran Member
                              • Jul 2014
                              • 2714

                              Originally posted by Limited-Ten
                              Slides come in different widths depending on mfg. we accommodate worse case scenario. Fusion uses STI width from what I've seen.
                              Well you would be the one to know
                              Fear is the spare change that will keep you broke

                              Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

                              Comment

                              Working...
                              UA-8071174-1