Unconfigured Ad Widget

Collapse

Surface grinding needed

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • BBR
    Member
    • Apr 2006
    • 196

    Surface grinding needed

    Hello all,

    Many moons ago I purchased 5 raw 1911 forgings. They needed a lot of work, but I figured why not. I would like to do something with them, but they need a few operations completed prior to me starting to finish them. I would like to have them surface ground to nominal dimensions. They have not had the rails cut nor any holes or fitting, so they are still <80%. Anyone withba surface grinder interested in dimensioning these up for me?

    Thanks,
    BBR
  • #2
    67Cuda
    Senior Member
    • Oct 2013
    • 1727

    Grinding is almost a niche service that will cost you "money"!

    If you can get anybody to help you.

    Good Luck..
    Originally posted by ivanimal
    People that call other member stupid get time off.
    So much for being honest.

    Comment

    • #3
      kcstott
      I need a LIFE!!
      • Nov 2011
      • 11796

      I have a surface grinder, but you ain't gonna like my pricing.

      Depending on how rough I'd be willing to bet some where north of $150 each. If they could be nested together it might get cheeper but again that depends on how rough they are

      Comment

      • #4
        HardwoodRods
        Senior Member
        • Mar 2011
        • 1093

        Gonna be pricy, Where are you located, that would be useful info........
        "A free people ought to be armed" George Washington, 1790

        "Don't fire unless fired upon. But if they mean to have war, let it begin here" Capt. John Parker, 19 April 1776, Lexington Green

        Comment

        • #5
          Greg B
          Member
          • Mar 2013
          • 295

          Are the sides any semblance of flat now? If they're badly warped, that increases time to set up.

          Comment

          • #6
            hermosabeach
            I need a LIFE!!
            • Feb 2009
            • 19897

            pictures
            Rule 1- ALL GUNS ARE ALWAYS LOADED

            Rule 2 -NEVER LET THE MUZZLE COVER ANYTHING YOU ARE NOT PREPARED TO DESTROY (including your hands and legs)

            Rule 3 -KEEP YOUR FINGER OFF THE TRIGGER UNTIL YOUR SIGHTS ARE ON THE TARGET

            Rule 4 -BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT
            (thanks to Jeff Cooper)

            Comment

            • #7
              liber
              Senior Member
              • Dec 2014
              • 1868

              Originally posted by 67Cuda
              If you can get anybody to help you.
              ^^this

              A lot of people will be reluctant to help you based on wording in the BATFE documents and the implications. Not clear of the person doing the work would need an FFL or not, but most all FFLs would probably be unlikely to help.

              As an alternative to a surface grinder, you would use a face mill followed up with lapping with wet/dry.
              sigpic
              --------- liber --------

              From my cold dead end mill...

              Comment

              • #8
                kcstott
                I need a LIFE!!
                • Nov 2011
                • 11796

                I think if he had access to a mill maybe he wouldn't have asked

                Comment

                • #9
                  BBR
                  Member
                  • Apr 2006
                  • 196

                  I have a mill but even with flood cooling its not giving me the finish I would like. I am using a carbide shell mill and it is chattering like crazy. I am also getting some deflection. It was recommended to have them surface ground so that's where we are at. I am located in the central valley.

                  BBR

                  Comment

                  • #10
                    liber
                    Senior Member
                    • Dec 2014
                    • 1868

                    Originally posted by BBR
                    I have a mill but even with flood cooling its not giving me the finish I would like. I am using a carbide shell mill and it is chattering like crazy. I am also getting some deflection. It was recommended to have them surface ground so that's where we are at. I am located in the central valley.

                    BBR
                    Have you calibrated the vertical head? Shouldn't chatter, reduce feed/cut until chatter disappears.
                    sigpic
                    --------- liber --------

                    From my cold dead end mill...

                    Comment

                    • #11
                      BBR
                      Member
                      • Apr 2006
                      • 196

                      Its been trammed. I will play with it some more. Thanks guys

                      BBR

                      Comment

                      • #12
                        Greg B
                        Member
                        • Mar 2013
                        • 295

                        How are you holding the frame?
                        Rigidity in your setup is directly related to your results.
                        In my experience, carbide tend to perform better with higher feed rates.
                        Additionally, once chatter occurs, it's difficult to get under it, for lack of a better term.

                        Comment

                        • #13
                          67Cuda
                          Senior Member
                          • Oct 2013
                          • 1727

                          A shell mill is the wrong cutting tool for milling what you have.

                          A shell mill will have large gaps between the inserts. Along with the diameter of the shell mill, this will put a lot of pressure on the smaller part.

                          I would use a 5 flute or more with high helix "1/2 inch carbide end mill, or even a smaller diameter one. This will have less cutting pressure, hence less or no chatter.

                          I understand you want to do it in one pass but wet sanding each side to remove milling marks will give a uniformed surface.
                          Originally posted by ivanimal
                          People that call other member stupid get time off.
                          So much for being honest.

                          Comment

                          • #14
                            kurac
                            Veteran Member
                            • Dec 2005
                            • 2917

                            We have always used these guys with good experience. http://www.advancedgrindinginc.com/about-us/
                            www.culinagrips.com
                            "custom grips for shooters by shooters"

                            Comment

                            • #15
                              milotrain
                              Veteran Member
                              • Apr 2011
                              • 4301

                              Shell mills actually leave worse finishes than single tooth cutters because any imbalance or out of tram shows up. What if you fly cut it with a super slow feed, or use the shell mill with only one cutter?
                              weg: That device is obsolete now. They replaced it with wizards.
                              frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                              Comment

                              Working...
                              UA-8071174-1