Unconfigured Ad Widget

Collapse

Bedding.

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • USMCM16A2
    Banned
    • Jul 2006
    • 4941

    Bedding.

    Folks,




    I need some help with bedding a stock. I have a new Boyds stock coming for my Ruger American standard. The stock is comng with new V blocks that the receiver fits into. Boyds advises that the blocks should be bedded to the stock.
    The stock is a laminate, what matierial should I use to bed? What order do I follow? Bedding compound, put v blocks into place, put everything together then tighten the receiver screws and let it set? Any help would be appreciated. A2
  • #2
    ar15barrels
    I need a LIFE!!
    • Jan 2006
    • 57202

    Devcon Plastic steel is a great bedding compound when you are bedding the receiver, but you are really only bedding those two little blocks into the stock so you can use something thinner like regular Devcon epoxy.

    Drill some little holes in the sides of the v blocks for the epoxy to lock into.
    Drill some holes into the sides of the v block pockets.
    Get some kiwi shoe polish and wipe it all over the underside of the receiver anywhere that the epoxy might get to.
    Wrap two bands of electrical tape around the barrel to make the barrel center in the stock when you finally are ready to set it in place.

    Mix up the epoxy and work some into all the little holes that you drilled on both the stock and the v blocks.
    Make sure you put enough epoxy into the pockets in the stock that the extra will flow out after you set the v blocks in place.

    Install the blocks and action and snug the screws down just tight enough to squeeze all the extra epoxy out.
    Let it setup 30 minutes and then pop the action out of the stock.
    Trim away any extra bedding material that you don't need, then re-install the action and snug it back into the stock and let it cure 24hrs.
    Last edited by ar15barrels; 04-12-2016, 10:53 AM.
    Randall Rausch

    AR work: www.ar15barrels.com
    Handguns: www.handgunbarrels.com
    Bolt actions: www.700barrels.com
    Foreign Semi Autos: www.akbarrels.com
    Most work done while you wait on a scheduled shop visit.

    Comment

    • #3
      USMCM16A2
      Banned
      • Jul 2006
      • 4941

      Randall thanks,........

      Randall,



      Thanks as always great one! Another calgunner said I could use JB Weld also, and follow the same series of steps. JB Weld ok? A2

      Comment

      • #4
        ar15barrels
        I need a LIFE!!
        • Jan 2006
        • 57202

        jb weld would be fine as long as it's sorta runny.
        You don't want a putty for this particular job.
        You want something that flows like maple syrup so it will get into all the little holes.
        Randall Rausch

        AR work: www.ar15barrels.com
        Handguns: www.handgunbarrels.com
        Bolt actions: www.700barrels.com
        Foreign Semi Autos: www.akbarrels.com
        Most work done while you wait on a scheduled shop visit.

        Comment

        • #5
          'ol shooter
          Veteran Member
          • Mar 2011
          • 4646

          The blocks in my Magnum fit really snug in my Boyds stock, and it shoots good as is. Might want to wait on buying any bedding compound until you actually receive it and test fit. Also, for a rimfire you can use HVAC aluminum tape to snug the fit up between the blocks and the stock, used by many 10-22 bench shooters between the receiver and stock, and it's not permanent. The issue I have with my Walnut stock is the action screws not holding torque due to wood compression when snugged. I will eventually be installing escutcheon bushings for the screws to tighten against, contacting the bedding block directly on the inside. The issue isn't as bad with a laminated stock.
          sigpic
          Bob B.
          (\__/)
          (='.'=)
          (")_(")

          Comment

          • #6
            baih777
            CGN/CGSSA Contributor
            CGN Contributor
            • Jul 2011
            • 5680

            You can find Devcon plastic steel at Ace Hardware.
            Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
            I really miss the good old Pomona Gun Shows.
            I'm Back.

            Comment

            Working...
            UA-8071174-1