Unconfigured Ad Widget

Collapse

Correct muzzle brake install?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • NATEWA
    Calguns Addict
    • Jun 2012
    • 5977

    Correct muzzle brake install?

    I don't know where I picked up this muzzle brake but don't think I installed it correctly. Currently, the two small holes are on the bottom. I wrenched it on there fairly tight. I secured the barrel in a vice and used some plastic type jaws to keep it in place.

    Holes on top or on the bottom?

    If on top, keep tightening it?

    Thanks
    Last edited by NATEWA; 06-20-2016, 10:20 AM.
  • #2
    NATEWA
    Calguns Addict
    • Jun 2012
    • 5977

    Thanks - just attached pic

    Comment

    • #3
      dwalker
      Veteran Member
      • Jul 2014
      • 2714

      The two holes on top are to help counter muzle rise. You need a set of shims or new crush washer to line it up when tight
      Fear is the spare change that will keep you broke

      Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

      Comment

      • #4
        dwalker
        Veteran Member
        • Jul 2014
        • 2714

        Originally posted by DeusExMachina
        Holes are probably for pin/weld. Bottom
        LOL someone did not look at the pic
        Fear is the spare change that will keep you broke

        Call him run-like-hell-when-shtf-guy or dial-911-guy but NEVER call an unarmed man "Security".

        Comment

        • #5
          jericho89
          Senior Member
          • Aug 2011
          • 1129

          yep holes on top. As stated need shims or you can have it pinned so that the holes are on top. If you keep it pointed down then you can get muzzle rise, and if you are prone you will get dirt flying up in the air.

          Comment

          • #6
            NATEWA
            Calguns Addict
            • Jun 2012
            • 5977

            Pic was not originally attached. Thanks for your help. I'll get some shims.

            Comment

            • #7
              baih777
              CGN/CGSSA Contributor
              CGN Contributor
              • Jul 2011
              • 5680

              Are you in socal ?
              Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
              I really miss the good old Pomona Gun Shows.
              I'm Back.

              Comment

              • #8
                copecom77
                Senior Member
                • Jan 2015
                • 1089

                If you end up needing shims check out Precision Armament. I got one of their brakes and ordered their shim kit, each shim has a marking on it and there are instructions on how to identify the shim that you need based on how many degrees of rotation you need and the marking on the shims. Made it easy.


                Sent from my iPhone using Tapatalk

                Comment

                • #9
                  NATEWA
                  Calguns Addict
                  • Jun 2012
                  • 5977

                  Nor cal and ended buying these (see link). One more question - install the shims with the crush washer or without?

                  Muzzle Brake Alignment Shim Set For Threaded Rifle Barrels (1/2") https://www.amazon.com/dp/B00J41C6LM..._tfCcxbP684W6S

                  Comment

                  • #10
                    baih777
                    CGN/CGSSA Contributor
                    CGN Contributor
                    • Jul 2011
                    • 5680

                    if you use shims only, use blue Loctite.
                    Been gone too long. It's been 15 to 20 years since i had to shelf my guns. Those early years sucked.
                    I really miss the good old Pomona Gun Shows.
                    I'm Back.

                    Comment

                    • #11
                      jericho89
                      Senior Member
                      • Aug 2011
                      • 1129

                      The crush washer acts like a lock washer. I would say with the crush washer and a little lock tite. But that's just me

                      Comment

                      • #12
                        Bullets&Whitewalls
                        Senior Member
                        • May 2012
                        • 2390

                        I have a similar brake, with mine I put the holes on top like others said. One thing I noticed about mine is those holes were slightly angled to the right. Either they were drilled wrong or I had a guess that maybe it was to direct gas away from the sight picture? The reason I'm posting this is I'm curious if you're is the same? And maybe someone can tell me if my thinking was right?? Honestly mine is a cheap EBay score so it could very well be drilled wrong lol. And yes I know it's doubtful to even see the gas or it be an issue if they were centered.

                        Comment

                        • #13
                          Saym14
                          Calguns Addict
                          • Jul 2009
                          • 7892

                          holes on the top will direct the gas up and keep the muzzle down. angled holes will reduce twisting.

                          Comment

                          • #14
                            NATEWA
                            Calguns Addict
                            • Jun 2012
                            • 5977

                            Shim set worked! GTG

                            Comment

                            Working...
                            UA-8071174-1