Unconfigured Ad Widget

Collapse

...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 6un5_4r3_N347
    Junior Member
    • Sep 2015
    • 9

    ...

    ...
    Last edited by 6un5_4r3_N347; 01-11-2016, 4:01 PM.
  • #2
    liber
    Senior Member
    • Dec 2014
    • 1868

    Make sure the spring is seated properly under the disconnecter. This problem can occur when it is not. They have a fatter flat end on one side and that goes on the bottom.
    sigpic
    --------- liber --------

    From my cold dead end mill...

    Comment

    • #3
      ar15barrels
      I need a LIFE!!
      • Jan 2006
      • 57200

      Disconnectors are usually quite soft.
      No need to re-harden them after shortening the nose.
      Randall Rausch

      AR work: www.ar15barrels.com
      Handguns: www.handgunbarrels.com
      Bolt actions: www.700barrels.com
      Foreign Semi Autos: www.akbarrels.com
      Most work done while you wait on a scheduled shop visit.

      Comment

      • #4
        ar15barrels
        I need a LIFE!!
        • Jan 2006
        • 57200

        Originally posted by 6un5_4r3_N347
        The disconnector seems hard.
        My file slides across it like glass without removing any material.
        If it does not need to be re-hardened, then that would make my life a lot easier.
        Whose parts?

        JP includes a soft disconnector with their gunsmith fit triggers and has no instructions to harden it after fitting.
        I did one with a file and then switched to doing them all on the surface grinder.
        The surface grinder just makes it so much easier to make a repeatable setup when I put the part back into the setup to grind a little more and then a little more...
        Randall Rausch

        AR work: www.ar15barrels.com
        Handguns: www.handgunbarrels.com
        Bolt actions: www.700barrels.com
        Foreign Semi Autos: www.akbarrels.com
        Most work done while you wait on a scheduled shop visit.

        Comment

        • #5
          Heretodaygonetomorrow
          Senior Member
          • Aug 2011
          • 582

          Originally posted by 6un5_4r3_N347
          It was definitely case hardened. Once I got through the case with a stone, a file could "bite" into the material with ease. The trigger group works well now and passes all safety and function tests. since I didn't remove any material from the bottom of the disconnector nose, I don't think it needs to be re-hardened... I hope.

          After testing fitting the the disconnector numerous times, I now have pin walk. Looks like a trip down to the store tomorrow. If it's not one thing it's another.

          Also ran into a short magazine catch/release issue. I Ordered an extended button from Aero Precision. That should show up in a couple of days.

          All that's left to do now is fit up the bolt catch release. On my last AR 15 build I ran into issues with that, so I'm going to mock it up before threading the retaining pin in.

          liber and ar15barrels, Thanks for your help.


          Are you saying that you're getting pin walking on the trigger pin? If so, it's because the hammer spring is not locking the trigger pin properly. First, make sure that you have the hammer spring mounted on the hammer the right way. Then, check the notches cut in the trigger that expose the trigger pin to the legs of the hammer pin. The notches may be cut too shallow to allow the legs of the hammer pin to settle properly into the grooves in the trigger pin. Also make sure that the groves in the trigger pin are lined up with the notches in the trigger so that the legs of the hammer spring will lock the trigger pin.

          Comment

          Working...
          UA-8071174-1