Unconfigured Ad Widget

Collapse

Please help with competition die setup

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sammy
    Veteran Member
    • Oct 2006
    • 3847

    Please help with competition die setup

    I am setting up a brand new RCBS Summit press with Redding competition dies for 308 using a .336 bushing.

    After getting the neck sizer setup I am getting 8 thousands of runnout on the case neck on my once fired cases. Before they are sized at most they have 1.5 thousands so it is the neck sizing process that is doing it. I have tried using the body sizer afterwards and it changes nothing. After neck sizing I tried turning the case 90 degrees and no luck with that either.

    What am I doing wrong??

    Thanks, Sammy
  • #2
    ocabj
    Calguns Addict
    • Oct 2005
    • 7924

    Are you letting the bushing free float? Tighten the decapping assembly all the way down until it contacts, then backing off a quarter turn.

    Distinguished Rifleman #1924
    NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
    NRL22 Match Director at WEGC

    https://www.ocabj.net

    Comment

    • #3
      sammy
      Veteran Member
      • Oct 2006
      • 3847

      Originally posted by ocabj
      Are you letting the bushing free float? Tighten the decapping assembly all the way down until it contacts, then backing off a quarter turn.
      Yes, it is setup correctly.

      Comment

      • #4
        Mike402
        Senior Member
        • Nov 2012
        • 555

        Assuming your fired necks are in the .34xx range, try initially sizing the entire neck with a .339 bushing, and then sizing half the neck with your .336. Doing this in conjunction with neck turning yields little to no runout for me.

        Comment

        • #5
          eric n
          Member
          • Oct 2013
          • 254

          What are you using to measure the runout?
          Do you know the chamber specs?
          Die screwed down?
          Decapper in?
          Centered in shellholder?
          That's a lot of runout.

          Are you measuring virgin brass? I would expect to see .003 total on new brass but my fired stuff barely moves the needle.... Try taking the decap rod out if you have it in
          Last edited by eric n; 12-04-2014, 9:26 PM.

          Comment

          • #6
            AandO
            Member
            • Nov 2014
            • 449

            You may want try a different lot of brass. How many firings etc.........

            The press is New, how about the Dies?

            I had a new Dillon Die (Made by Redding) that was bad. It happens.....

            Comment

            • #7
              jh4db536
              Junior Member
              • Dec 2012
              • 77

              I think the brass is bent. The way I deal with this is to small base full length resize those brass in my type s die without pushing the shoulder (using a +0.010 shellholder). It will reduce the runout a lot.

              My body die or other standard full length dies doesnt help.

              Comment

              • #8
                J-cat
                Calguns Addict
                • May 2005
                • 6626

                Originally posted by Mike402
                Assuming your fired necks are in the .34xx range, try initially sizing the entire neck with a .339 bushing, and then sizing half the neck with your .336. Doing this in conjunction with neck turning yields little to no runout for me.
                I used to do that too, then moved on to a Lee Collet Neck Die. Now I just don't give a sheet and FL size everything.

                Comment

                • #9
                  sammy
                  Veteran Member
                  • Oct 2006
                  • 3847

                  Originally posted by eric n
                  What are you using to measure the runout?
                  Do you know the chamber specs?
                  Die screwed down?
                  Decapper in?
                  Centered in shellholder?
                  That's a lot of runout.

                  Are you measuring virgin brass? I would expect to see .003 total on new brass but my fired stuff barely moves the needle.... Try taking the decap rod out if you have it in
                  I am using the Sinclair concentricity gauge http://www.sinclairintl.com/reloadin...prod37479.aspx

                  The die is screwed down tight, decapper in, centered in shell holder. Yes it is a lot of runnout. These are once fired PMC, Lake City, and others.

                  Comment

                  • #10
                    sammy
                    Veteran Member
                    • Oct 2006
                    • 3847

                    Originally posted by jh4db536
                    I think the brass is bent. The way I deal with this is to small base full length resize those brass in my type s die without pushing the shoulder (using a +0.010 shellholder). It will reduce the runout a lot.

                    My body die or other standard full length dies doesnt help.


                    I am checking the brass before it goes into the sizer. It is near perfect but comes out with the runnout after sized.

                    It must be the die. I sent an email to Redding.

                    Comment

                    • #11
                      AandO
                      Member
                      • Nov 2014
                      • 449

                      Originally posted by sammy
                      I am checking the brass before it goes into the sizer. It is near perfect but comes out with the runnout after sized.

                      It must be the die. I sent an email to Redding.
                      Do you own any other Sizing Dies in the same Caliber?

                      If so, try using them to confirm the issue is with the Redding Die.

                      Obviously if the same issue occurs then it would be the Brass.

                      Comment

                      • #12
                        ocabj
                        Calguns Addict
                        • Oct 2005
                        • 7924

                        Have you tried removing the expander ball from the stem?

                        Distinguished Rifleman #1924
                        NRA Certified Instructor (Rifle and Metallic Cartridge Reloading) and RSO
                        NRL22 Match Director at WEGC

                        https://www.ocabj.net

                        Comment

                        • #13
                          Mike402
                          Senior Member
                          • Nov 2012
                          • 555

                          Originally posted by sammy
                          I am checking the brass before it goes into the sizer. It is near perfect but comes out with the runnout after sized.

                          It must be the die. I sent an email to Redding.
                          Did you try a different bushing?

                          Comment

                          • #14
                            eric n
                            Member
                            • Oct 2013
                            • 254

                            I have the same...Forgive me if this sounds elementary. Are you moving the blocks so the case body sits on both sets of bearings?
                            Do you get the same amount of tir on all the headstamps? If not, try and borrow a few pieces of lapua brass.
                            Try it with out the expander button and see if it improves as well.

                            Comment

                            • #15
                              sammy
                              Veteran Member
                              • Oct 2006
                              • 3847

                              Originally posted by AandO
                              Do you own any other Sizing Dies in the same Caliber?

                              If so, try using them to confirm the issue is with the Redding Die.

                              Obviously if the same issue occurs then it would be the Brass.
                              I do but am waiting on shell holders that are in the mail.

                              Comment

                              Working...
                              UA-8071174-1