I use the Imperial sizing wax on all my cases and haven't had one stick yet. Try it on your .223 cases, you won't be disappointed. It comes right off in about 20-30 minutes in the tumbler using corn cob media (and the cases get nicely polished at the same time).
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
Stuck Case
Collapse
X
-
There's a little trick to using One Shot in a new die. A new die needs to be seasoned with Hornady's Unique case Lube. After cleaning the die to remove all the factory preservative oil, lube 5 cases with a thin coating of Unique, paying attention to coat the case body near the head, and size. Thereafter use One Shot to your heart's content, cases will not stick. I have been using One Shot since it was introduced and learned this trick early on. Doesn't matter if they are straight walled handgun or rifle cases, bottle necked cases or whatever - they all resize nicely. If you don't want to buy a tub of Unique, then after cleaning the die, spray a liberal coat of One Shot into the die, allow to dry and then recoat it. After it dries begin sizing.
If you clean the die for any reason, treat it as a new die and use the Unique as before, or spray it again as above.
Another trick is to be sure the cases are sitting on their head with no obstruction masking the spray. I place 50 cases in an MTM cartridge box, mouth down, place a piece of cardboard over the top of the box, invert the entire thing on my bench and carefully lift off the box. With all the cases separated and standing up, I can easily spray One Shot from opposite directions to coat all exterior surfaces and lube the interior of the necks. Several batches can be lubed at a time, allowed to dry and placed in a bin for resizing. I cut the lid off some old MTM boxes of various sizes to facilitate the process. The most important part is to coat the case near the solid internal web all the way to the extractor groove or rim.
After sizing I tumble clean the cases, before priming or loading.
One Shot is just too easy and convenient for me to mess with the other stuff, except when forming cases as part of converting them to different cartridges or calibers, then I use the Unique or Corbin's swagging lube.Comment
-
I have never had an issue with One Shot. You do have to follow the instructions to the letter. Dont skip the step where you treat the die (as the above poster stated).Comment
-
I use One Shot extensively for mass .308 and .223 sizing. I lay all cases out on some newspaper and spray lightly, shift the cases and spray lightly one more time. After that, I hold a Q-tip over the cases and spray the Q-tip. I use the Q-tip to lube inside about 20 case necks before spraying the Q-tip again. Each time I spray the Q-Tip, the overspray hits the cases on the newspaper.
Using the above technique, I haven't had any stuck cases. But then again, it might not mean anything since I use Dillon Carbide .308 and .223 dies.Comment
-
Steve Wagner has a quik n ezy method on his site.
Basically the same as my RCBS kit, just using normal DIY guy stuff people have laying around.
JM2cComment
-
PM me your address and I will send you some lanolin mixed with IPA. It is much better than one shot and much cheaperComment
-
Which ratio do you use for your mix?It is much better than one shot and much cheaper...because the journey is the worthier part...The Shepherd's TaleComment
-
10-12:1 is the norm. if you cant find 99% alcohol locally use the red iso heet. Verify by looking at the ingredients it should say alcohol.
ETA: also look at frys or computer repair shops as they often use 99% alcohol for cleaning.primer, powder, projecile, press, load, fire repeat!Comment
-
Thanks.
I'd read one mix that was 8:1, but someone said that was too thick.
Thanks for the suggestion on the Computer repair places as a source of 99%...I can only find 91% locally.
Do you have a good source of lanolin?...because the journey is the worthier part...The Shepherd's TaleComment
Calguns.net Statistics
Collapse
Topics: 1,870,920
Posts: 25,177,503
Members: 358,862
Active Members: 5,395
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 34734 users online. 149 members and 34585 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

The seating stem is too weak to tap the case out.
Comment