Unconfigured Ad Widget

Collapse

Concentricity specification

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Dhlcycler
    Junior Member
    • Oct 2014
    • 48

    Concentricity specification

    As a follow up to my carbine ammo problem, I measured a number of .30 Armscor carbine rounds that had asymmetric bulges. Although the overall case mouth diameter, at the bulge, was within SAAMI specification of 0.336, I suspect that the nature of the bulge is producing an effective diameter greater than what I measure.

    Is there any spec for bullet concentricity? I think the SAAMI specs assume the bullet is centered in the shell, but what if it isn't? Anyway to measure this besides trying to chuck in a lathe and dial indicate on the bullet?
  • #2
    bsumoba
    Veteran Member
    • Sep 2012
    • 4217

    if you're simply talking about bullet concentricity relative to the base of the cartridge, then what i expect with my handloads is 0.001". I do get some up to 0.003", but if I do, I adjust my die or my reloading procedure to make it right.

    i havent bought factory ammo in a LONG time so I couldnt measure one for you.

    i have never heard of a SAAMI spec for bullet concentricity.

    there are lots of tools to meaure this. hornady's concentricity gauge comes to mind.
    Visit- www.barrelcool.com
    The Original Chamber Flag and Barrel Cooler in 1
    Instagram: barrelcool_

    Comment

    • #3
      J-cat
      Calguns Addict
      • May 2005
      • 6626

      There is no spec. I recently measured Federal Gold Medal Match 223 ammo and it had .013" runout? Yeah, that's match ammo.

      Comment

      • #4
        JMP
        Internet Warrior
        CGN Contributor - Lifetime
        • Feb 2012
        • 17056

        You can get a concentricity tool/gauge, but if you are shooting Armscor that should be the least of your concerns. Just get virtually ANY other ammo, and results will improve.

        Comment

        • #5
          Dhlcycler
          Junior Member
          • Oct 2014
          • 48

          There should be a specification. To be conservative it should be that the OD, including run out, should be no greater than the MAX od spec.

          I found more that did exceed the .336 OD spec. How this company can claim they have effective QC is a mystery to me.

          Comment

          • #6
            JMP
            Internet Warrior
            CGN Contributor - Lifetime
            • Feb 2012
            • 17056

            Originally posted by Dhlcycler
            I found more that did exceed the .336 OD spec. How this company can claim they have effective QC is a mystery to me.
            Armscor quality control.

            I hope you didn't buy too much.

            Comment

            • #7
              bsumoba
              Veteran Member
              • Sep 2012
              • 4217

              to be honest, you cannot expect too much from armscor.

              most manufactures will QC based on an AQL sampling. To have them inspect every round is crazy talk and you might as well go buy more expensive ammo from more reputable companies as they probably have tighter QC inspection. and even then, as J-cat mentions, their runout is not sub- 0.003", which is my requirement when I reload.

              you get what you pay for is all I am saying.

              some people have even found 2 bullets in one cartridge in winchester white box.

              if you want to mitigate all these issues, I'm sorry to say, but you need to reload yourself and trust your own made ammo.
              Visit- www.barrelcool.com
              The Original Chamber Flag and Barrel Cooler in 1
              Instagram: barrelcool_

              Comment

              • #8
                Rock6.3
                Senior Member
                • Nov 2010
                • 2431

                It's a 30 Carbine.

                They are fun to shoot, but accurate is not on the list of their claim to fame.

                And if it's concentric going into the magazine, it won't be after it runs up the feed ramp and into the chamber.

                Comment

                • #9
                  bigedp51
                  Member
                  • Dec 2009
                  • 263

                  Dhlcycler

                  In order to load accurate ammunition with minimum runout you need a neck thickness gauge and a runout gauge.

                  Below is what I think you mean by "asymmetric bulges" and might be caused by case wall and neck case thickness variations. (poorly made cartridge cases)

                  Below this Remington .223 case has .004 variation in neck wall thickness.





                  So be forewarned, the SAAMI only sets "guidelines" and not quality standards and you have cheap .30 carbine "blasting ammo".

                  And the .30 Carbine has never won any benchrest competitions.

                  Comment

                  • #10
                    Dhlcycler
                    Junior Member
                    • Oct 2014
                    • 48

                    Originally posted by JMP
                    Armscor quality control.

                    I hope you didn't buy too much.
                    I bought about 500 rds. They replaced 150, and about 100 rounds of the replacements were good. So I netted out about 450 usable rounds.

                    I won't be buying any more.

                    Comment

                    • #11
                      Dhlcycler
                      Junior Member
                      • Oct 2014
                      • 48

                      Originally posted by bsumoba
                      to be honest, you cannot expect too much from armscor.

                      most manufactures will QC based on an AQL sampling. To have them inspect every round is crazy talk and you might as well go buy more expensive ammo from more reputable companies as they probably have tighter QC inspection. and even then, as J-cat mentions, their runout is not sub- 0.003", which is my requirement when I reload.

                      you get what you pay for is all I am saying.

                      some people have even found 2 bullets in one cartridge in winchester white box.

                      if you want to mitigate all these issues, I'm sorry to say, but you need to reload yourself and trust your own made ammo.
                      I have not invested in reloading equipment. And for 30 carbine I should not have to. I may need to spend a little more and get ammo that's in spec and won't get jammed in the chamber or action.

                      Comment

                      • #12
                        Dhlcycler
                        Junior Member
                        • Oct 2014
                        • 48

                        Originally posted by Rock6.3
                        It's a 30 Carbine.

                        They are fun to shoot, but accurate is not on the list of their claim to fame.

                        And if it's concentric going into the magazine, it won't be after it runs up the feed ramp and into the chamber.
                        We are not talking a mil concentricity. More like 10 mils. See the photos in my previous post.

                        No feed ram would cause these distortions.

                        Comment

                        Working...
                        UA-8071174-1