Unconfigured Ad Widget

Collapse

Redding neck sizing die problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • skyline
    Senior Member
    • Mar 2012
    • 500

    Redding neck sizing die problem

    Hello cal gunners have a bit of a problem . I am reloading 223 fired from a bolt action rifile so it has been case formed I bought a redding neck sizing die
    And on some cases the bullets fit snug and perfect. And in others they are so tight they won't even go in at all and others are so loose they fall inside the case
    I have checked all cases to make sure they are trimmed and are with in spec .
    Can somebody tell me what I am doing wrong
  • #2
    Seaweed02
    Senior Member
    • Jun 2012
    • 1650

    tagged

    Tagged for later as I too need to know this.

    Comment

    • #3
      Bastard
      • Jul 2009
      • 2209

      is it the competition bushing die?

      actually that really does't matter, check the neck thickness, you might have to turn the necks to get the consistent thickness

      Comment

      • #4
        damndave
        I need a LIFE!!
        • Oct 2008
        • 10858

        Which die set did you buy? Are they bushing dies?

        Comment

        • #5
          CSACANNONEER
          CGN/CGSSA Contributor - Lifetime
          CGN Contributor - Lifetime
          • Dec 2006
          • 44094

          Have you turned your necks? What is the thickness of the brass at the necks? Is it consistent through your entire batch? Do you anneal?
          NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
          California DOJ Certified Fingerprint Roller
          Ventura County approved CCW Instructor
          Utah CCW Instructor


          Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

          sigpic
          CCW SAFE MEMBERSHIPS HERE

          KM6WLV

          Comment

          • #6
            FLIGHT762
            Veteran Member
            • Mar 2009
            • 3072

            Originally posted by Bastard
            is it the competition bushing die?
            This ^^^^^^^^^^^^^

            Originally posted by AlliedArmory
            Which die set did you buy? Are they bushing dies?
            And this ^^^^^^^^^^^^^^^^^^^^^

            O/P, did you buy the Redding Competition "S" bushing neck or F/L sizing die from Redding?

            Are you using a "S" bushing die without the proper bushing installed???

            That might be your issue. We need a little more information to help you.

            Comment

            • #7
              Metal God
              Senior Member
              • Apr 2013
              • 1839

              We need a little more information to help you.
              ^^^^^this^^^^^

              Because

              some cases the bullets fit snug and perfect. And in others they are so tight they won't even go in at all and others are so loose they fall inside the case
              I can't think of any reason you get all three of those in one die . A combo of the first two or the first and last and I can see why but all three has me stumped .

              What bullets are you using ? Uneven brass thickness and crappy bullets that are not uniform diameter from bullet to bullet maybe ?? just a thought ,

              Are you using the expander ball ?
              Last edited by Metal God; 10-03-2014, 8:03 PM.
              Tolerate
              allow the existence, occurrence, or practice of (something that one does not necessarily like or agree with) without interference.

              Anyone else find it sad that those who preach tolerance CAN'T allow the existence, occurrence, or practice of (something that they do not necessarily like or agree with) without interference.

              I write almost everything in a jovial manner regardless of content . If that's not how you took it please try again

              Comment

              • #8
                skyline
                Senior Member
                • Mar 2012
                • 500

                Sorry about that I am using redding neck die series a model number 81111
                And I am using range brass
                How do I turn the neck I have never heard of that before

                Comment

                • #9
                  skyline
                  Senior Member
                  • Mar 2012
                  • 500

                  Also it is a single die that I bought

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    You use a neck turner. But, you need to know why you want to neck turn before you do it. You will need to match the thickness of your brass to the neck sizer (or bushing) you want to use. Neck turning could result in not enough neck tension if your neck sizer or bushing is too big for the thickness of the brass that you turn your necks down to.

                    Mixed range pick up brass will not be consistent and will lead to differences in neck tension. I'm betting that this is your problem.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      Wrangler John
                      Senior Member
                      • Oct 2009
                      • 1799

                      Are you using the expander ball? The die will reduce the O.D. of the neck smaller than necessary to hold the bullet, the expander will size the I.D. of the neck to just slightly smaller than the bullet (somewhere around 0.002" - 0.004") to hold it in place. This final I.D. should be uniform regardless of neck thickness that's why it's part of the process.

                      As CSACANNONEER wrote above, using unknown salvaged brass can cause many problems. I never use any salvaged brass, not even that sold commercially as once fired.

                      If you need some inexpensive good quality brass try this: http://www.grafs.com/retail/catalog/...roductId/12628 I use it in varmint rifles that shoot very small groups and have never experienced the problem you are, indeed with any new commercial brass.

                      Getting into neck turning requires a tubing micrometer, neck turning mandrels or pilots, and a turning tool. It's time consuming and unnecessary for most shooters. I do not turn necks anymore for that reason. Here's some tools as an example:







                      Comment

                      • #12
                        krwada
                        Senior Member
                        CGN Contributor
                        • Jun 2013
                        • 1457

                        Sizing mixed range brass

                        For starters ... You will get absolutely zero ... I mean NO benefit from neck sizing mixed range brass. If you are going to size the pickup brass from the range, then I recommend you full length size the stuff using a Full length Sizer die.

                        The neck sizer die model you are using appears to be a basic neck sizer. The neck sizer you are using does use an expander ball for expanding the neck after sizing it down.

                        The fact that you are getting wildly varying results seems to indicate that you may not have the die properly adjusted. I would check the adjustment 1st. The other thing is that maybe some of the brass is just over worked. I would just throw away the brass where the projectiles do not fit. After all... you are using the real cheap, if not free range brass no?

                        Comment

                        • #13
                          Car83
                          Member
                          • Jan 2013
                          • 399

                          Are you neck sizing brass that is fire formed in your guns chamber?

                          Comment

                          • #14
                            skyline
                            Senior Member
                            • Mar 2012
                            • 500

                            I think you guys are right I am trying to get accuracy with second hand brass I believe that is my problem no constancy thank you all for your words of wisdom I will be ordering new brass

                            Comment

                            • #15
                              bigedp51
                              Member
                              • Dec 2009
                              • 263

                              I full length resize all my cases because I get better accuracy, and I believe in the rat turd in the violin case theory

                              And now a word from Team Lapua USA.



                              Bottom line, full length resizing reduces any misalignment problems caused by imperfect cases that do not have a uniform case wall thickness and warped on their first firing. (the warped banana shaped case)

                              Last edited by bigedp51; 10-05-2014, 12:38 AM.

                              Comment

                              Working...
                              UA-8071174-1