Unconfigured Ad Widget

Collapse

OCW Interpretation Help

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • #16
    LynnJr
    Calguns Addict
    • Jan 2013
    • 7959

    The OCW is a waste of too much ammo.Stick to "Ladder" testing.

    44.1 grains would be my choice as well.

    In a OCW Test or a "Ladder Test" you are only interested in vertical stringing and must ignore any and all horizontal.

    You are looking for a powder charge only and not a final load.Once you remove the vertical you can then play with the seating depth to achieve best accuracy.If you start out at the full jam length you only have one direction to go with the seating depth..
    Lynn Dragoman, Jr.
    Southwest Regional Director
    Unlimited Range Shooters Association (URSA)
    www.unlimitedrange.org
    Not a commercial business.
    URSA - Competition starts at 2000 yards!

    Comment

    • #17
      ar15barrels
      I need a LIFE!!
      • Jan 2006
      • 57200

      100yd testing is a waste.
      Re-run ladder test at 400yds and beyond to actually SEE a significant swing and find the sweet spot.
      1 round per charge weight in 0.2gr steps over about a 2gr range will show you where you want to be.
      Randall Rausch

      AR work: www.ar15barrels.com
      Handguns: www.handgunbarrels.com
      Bolt actions: www.700barrels.com
      Foreign Semi Autos: www.akbarrels.com
      Most work done while you wait on a scheduled shop visit.

      Comment

      • #18
        LynnJr
        Calguns Addict
        • Jan 2013
        • 7959

        Exodus 343
        This is how I would proceed.
        When doing a "Ladder Test" you always follow the 1% rule which simply means your incremental powder changes will be 1% of your load.

        In your case you are using 44 grains of powder so you would use 0.4 grains increments.

        Load up 5-6 rounds at 42.0 grains so you can get on paper and be all centered up.

        Now load one round at 42.4 42.8 43.2 43.6 44.0 44.4 44.8 45.2 and 45.6 grains.

        On the seating depth you want the bullet sticking out of the case as much as possible.

        If you are restricted by a magazine you would seat all of your rounds to the maximum length that will fit in your magazine.

        If you are not using a magazine and are just single feeding the rifle full length size one case and do not put a primer or any powder in the case.Take one of the bullets you will be using and rest it on the mouth of the case and slide the bolt forward.You most likely won't be able to close the bolt so take a rubber mallet and tap on the back of the bolt until it will close.
        DO NOT TAP ON THE BOLT HANDLE.
        TAP ONLY ON THE BACK OF THE BOLT OR FIRING PIN ASSEMBLY.
        You can actually knock a handle off by tapping on it.
        Now lift the bolt handle all the way up and with the palm of your hand bang the bolt open.

        This will give you what is commonly called the full jam length which simply means you can not seat a bullet any longer or the closing of the bolt will re-seat the bullet deeper into the case.

        Go to the range and staple up a target backwards so the whole target is white.

        Take a ball point pen and make a dot in the middle of the paper.The dot should be large enough that you can see it but not much larger.If you make the dot larger you will tend to aim the rifle with less precision and we don't want that.You want to be at your scopes maximum power setting as well because this will allow an even smaller dot to be used.

        Fire one or two of your 42.0 loads and adjust your turrets so you are very close to the dot but not close enough to put a bullet through it.If you put a bullet through it your aiming point will become larger and we don't want that.

        If all went well you are ready to shoot your "Ladder Test".

        If you needed to make a lot of scope adjustments change to a new target so you don't shoot through an existing hole or get confused.

        Shoot your rounds at a comfortable but evenly spaced time frame until you see signs of pressure or reach book max whichever comes first.

        You are only interested in vertical dispersion so don't worry if a round or two is wide left or wide right.

        You should see a few rounds that don't seem to climb vertically and this is what is called a node.

        Nodes have width dependent on the volume of the case.A 6BR sized case will typically have a node about 0.5 grains wide.A 50 bmg will have a node as much as 15 grains wide which means your powder charge is much less critical as case volume goes up in size.

        If you had 3 rounds that showed very little vertical and those 3 rounds were at 43.0 43.4 and 43.8 grains of powder you would want to be in the center of the node or 43.4 grains.

        This will allow you to load up around 40 rounds in order to find your ideal seating depth.Three rounds at the full jam length or your magazines maximum length then go shorter in increments of 0.005 inches.

        What will happen is your groups will shrink up then get larger then shrink up again.If the rifle is intended for competition were one shot is fired at a time in a controlled environment you can use the seating depth length that is the longest or even hard into the lands.

        If your using the rifle for hunting or cycling rounds through a magazine you would most likely use the shorter seating depth "sweet-spot" to avoid any cycling issues like sticking a bullet into the lands and dumping powder in the bolt lug recess.

        You can now go back and make minor adjustments to your powder charge and seating depth to optimize your load if its not already good enough,.
        Lynn Dragoman, Jr.
        Southwest Regional Director
        Unlimited Range Shooters Association (URSA)
        www.unlimitedrange.org
        Not a commercial business.
        URSA - Competition starts at 2000 yards!

        Comment

        Working...
        UA-8071174-1