Unconfigured Ad Widget

Collapse

Reloading 7.62x39

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Enfield47
    Calguns Addict
    • Sep 2012
    • 6385

    Reloading 7.62x39

    I'm looking at getting an RCBS two die set that comes with two expanders - .308 and .310. My bullets are .310 so would I use the .310 expander or try for a much tighter fit using the .308? I'm worried about crushing the neck while seating because the bullets are flat based.

    What size expander are you guys using for 7.62x39?
  • #2
    CSACANNONEER
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Dec 2006
    • 44094

    Use the .310 one.
    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
    California DOJ Certified Fingerprint Roller
    Ventura County approved CCW Instructor
    Utah CCW Instructor


    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

    sigpic
    CCW SAFE MEMBERSHIPS HERE

    KM6WLV

    Comment

    • #3
      Divernhunter
      Calguns Addict
      • May 2010
      • 8753

      Yes the .310 one.
      If you are shooting the ammo in a mini14 only then you can use .308 bullets and the .308 expander since the mini 14 has a .308 barrel.
      A 30cal will reach out and touch them. A 50cal will kick their butt.
      NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
      SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

      Comment

      • #4
        Enfield47
        Calguns Addict
        • Sep 2012
        • 6385

        This will be for an SKS. The reason I asked is because some reviews said the .310 left the bullets a little loose in the neck so they ended up switching to the .308 expander. They were using boat tail bullets though and mine are flat base.

        Comment

        • #5
          FLIGHT762
          Veteran Member
          • Mar 2009
          • 3072

          I'll be the third one who reloads for the 7.62X39 who will tell you to use the .310" expander with .310" bullets. You're over thinking this. If you are so worried about this, load up a couple of dummy rounds (no primer or powder) and see for yourself.

          If it's a big freaking mistake, you can pull the bullets and use the .308 expander, although my experience along with the other two posters recommend
          the .310".

          Comment

          • #6
            hoisumguo
            Member
            • Aug 2012
            • 152

            .310 , haven't had a loose one yet.

            -Hoi

            Comment

            • #7
              CGT80
              Veteran Member
              • Jul 2008
              • 2981

              Try .310, especially if you are using cast lead bullets. I don't load that round, yet, but I do load for 30-30 and 30-06 with lead. Cast boolit guys are always looking for bigger expanders as .311 is common for lead boolits. Lead can be swagged down by the neck of the brass. Jacketed bullets wouldn't be as critical but you still want a consistent fit. I like to push the bottom of the cartridge with my thumbs while the bullet is up against a steady steel surface, and see if I can push the bullet in the case more than what I seated it to. If I can, the neck tension or crimp are not good enough, and it could be from a case that is expanded too much.
              He who dies with the most tools/toys wins

              Comment

              • #8
                Enfield47
                Calguns Addict
                • Sep 2012
                • 6385

                Thanks for the help guys. Now I need to get a good quantity of brass and I'll be on my way.

                Comment

                • #9
                  SmokeWagon
                  Member
                  • May 2011
                  • 220

                  Originally posted by Enfield47
                  Thanks for the help guys. Now I need to get a good quantity of brass and I'll be on my way.
                  Let me know where you find some brass Brian. I would love to shoot my SKS again but all you can find is the damn Russian ammo that you can't shoot at any of the ranges. I also don't feel like driving half a day to get to some BLM land either, although I've read that you can't even shoot that ammo out there now as well.
                  NRA Life Member
                  GOA
                  GOC

                  Comment

                  • #10
                    BruinGuy
                    Senior Member
                    • Apr 2011
                    • 1456

                    I like the Lee die set myself; the FCD is useful for uniformity on the rim and a little crimp is a good thing. It too comes with a .308 and .310 pin. I use the .310 but have found that Hornady's .310 123gr bullets are a touch loosey goosey, while the PPU .310 bullets are snug. (Xtreme's plated 7.62x39 bullets are snug, but they actually measure .312 so no surprise there).

                    I tried using the .308 expander for the Hornady bullets, and it worked even with the flat base bullet, but it was tight and put a little bullet bulge in the neck that I expect will shorten the brass's life over time.

                    If you use the RCBS dies and .310 expander and it's too loose, just switch to the .308 expander. It will still work fine and so long as you go slow and position the bullet carefully you shouldn't experience crushed necks.
                    Originally posted by CSACANNONEER
                    Keep in mind that you don't have a clue.

                    Comment

                    • #11
                      Enfield47
                      Calguns Addict
                      • Sep 2012
                      • 6385

                      Originally posted by SmokeWagon
                      Let me know where you find some brass Brian. I would love to shoot my SKS again but all you can find is the damn Russian ammo that you can't shoot at any of the ranges. I also don't feel like driving half a day to get to some BLM land either, although I've read that you can't even shoot that ammo out there now as well.
                      It's fairly elusive right now, that's for sure. I saw some new Prvi at Phillips Wholesale a couple of weekends ago for $40/100. I was going to pick some up but the powder and primers cost me about $300 so I had to pass. You should join us for the WEGC C&R shoots on the 2nd Sunday of each month. You can shoot bimetal rounds there since it is a private range.

                      Originally posted by BruinGuy
                      I like the Lee die set myself; the FCD is useful for uniformity on the rim and a little crimp is a good thing. It too comes with a .308 and .310 pin. I use the .310 but have found that Hornady's .310 123gr bullets are a touch loosey goosey, while the PPU .310 bullets are snug. (Xtreme's plated 7.62x39 bullets are snug, but they actually measure .312 so no surprise there).

                      I tried using the .308 expander for the Hornady bullets, and it worked even with the flat base bullet, but it was tight and put a little bullet bulge in the neck that I expect will shorten the brass's life over time.

                      If you use the RCBS dies and .310 expander and it's too loose, just switch to the .308 expander. It will still work fine and so long as you go slow and position the bullet carefully you shouldn't experience crushed necks.
                      Thanks for the tips. This seems to be one of the most popular calibers that very few reload for. I know I can't beat the price of steel cased ammo but I can make much better ammo for not much more.

                      I looked at the Lee die set and was tempted to get it because I've had good luck with them - I have five other Lee sets that work great. My main reason for going with RCBS is their lifetime warranty and I can get if for the same price.

                      Comment

                      • #12
                        JagerDog
                        I need a LIFE!!
                        • May 2011
                        • 15889

                        $100/500

                        Palestine is a fake country

                        No Mas Hamas



                        #Blackolivesmatter

                        Comment

                        • #13
                          Enfield47
                          Calguns Addict
                          • Sep 2012
                          • 6385

                          Great deal, thanks!

                          Comment

                          • #14
                            ArmedCMT
                            Senior Member
                            • Nov 2012
                            • 2036



                            .20/rd aint the cheapest but they have it in stock and they ship pretty fast.

                            Comment

                            • #15
                              6mmintl
                              Veteran Member
                              • Apr 2008
                              • 4822

                              You can polish the .310 expander ball (which you should do anyway) to .oo1" smaller them measured.

                              If your single loading try seating the bullet out longer to get better accuracy, or try 7.62x54R bullets in the 146-150 grain weight range and seat them out longer, you will be surprised how accurate they are.

                              Comment

                              Working...
                              UA-8071174-1