Unconfigured Ad Widget

Collapse

Primer seating funky

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • gomatty
    Member
    • Aug 2012
    • 300

    Primer seating funky

    Just finished my first batch of reloads. On two cases getting the primer in was harder than the others and they look a little different than the rest as well. I think it's from the spent primer not releasing completely and leaving the sides inside the pocket when decapping. Is this something I should not worry about or should I just discard them? The two on top in the photo are the ones of concern. Feedback is appreciated.


    "Anybody can do it...with tools" - Raisin' Rey
  • #2
    russt
    Senior Member
    • Feb 2012
    • 1039

    i doubt the sides were left in the pocket, ive never seen that and if it happened i doubt a new primer would fit. from the pictures they look fine, but make sure the primers are sitting flush or below flush with the bottom of the shell casing. some cases have crimped primers which make it really hard if even possible to seat a new primer without removing the crimp, but in the picture the pockets dont appear to be crimped. if they are sitting properly then they should be good to go. what did you use to prime them?

    Comment

    • #3
      Germz
      Vendor/Retailer
      • Apr 2013
      • 4691

      what are you priming with? let me guess, lee auto-prime? this happens to me too sometimes, i just rotate the cartridge and give it another press. sometimes it will seat unevenly.
      Retired Account

      Comment

      • #4
        gomatty
        Member
        • Aug 2012
        • 300

        I'm using the lee breech press with the on-press safety primer. They are seated flush or below like the others. Thanks for the replies!
        "Anybody can do it...with tools" - Raisin' Rey

        Comment

        • #5
          HighLander51
          Banned
          • Feb 2010
          • 5144

          Originally posted by gomatty
          Just finished my first batch of reloads. On two cases getting the primer in was harder than the others and they look a little different than the rest as well. I think it's from the spent primer not releasing completely and leaving the sides inside the pocket when decapping. Is this something I should not worry about or should I just discard them? The two on top in the photo are the ones of concern. Feedback is appreciated.

          No, that is NOT possible. What press are are you using? The primers do look very flat, which is not normal, with any press, or hand prime. Check to see if there is some particle on top of the anvil that presses the primer in. Since you are brand new to reloading, you need to develop the feel for seating primers.

          Your avatar shows a right handed shooter with left eye dominance, get rid of that.
          Last edited by HighLander51; 03-09-2014, 8:54 PM.

          Comment

          • #6
            Witch Hunter
            Member
            • Oct 2013
            • 174

            If you use a primer pocket uniformer, this will not happen. Looks like you had some dirty or undersize primer pockets.

            Comment

            • #7
              J-cat
              Calguns Addict
              • May 2005
              • 6626

              Could be they were crimped.

              Comment

              • #8
                ironhorse1
                Senior Member
                • Nov 2012
                • 1019

                Those primer pockets appear to have been crimped just as J-cat has mentioned.

                You need to remove the crimp before priming with a hand held reamer.

                Then you should have no further problems.

                irh

                Comment

                • #9
                  Bastard
                  • Jul 2009
                  • 2209

                  as others have mentioned, they are crimped... and yes there are people that crimp 9mm, bastards!!!

                  Comment

                  • #10
                    gomatty
                    Member
                    • Aug 2012
                    • 300

                    I investigated a little more and I think these must be crimped. I have another case that is identical but deprimed. It looks like there is an extra lining in the pocket. So it's not safe to run these cases as is even though I didn't get the crimp out and the primers a bit misshapen?

                    Re: my avatar...it's really funny that you noticed that. The picture is not me but of Hunter S. Thompson. However, I happen to be right hand, left eye dominant and I've been working on using my left hand much more.
                    "Anybody can do it...with tools" - Raisin' Rey

                    Comment

                    • #11
                      Germz
                      Vendor/Retailer
                      • Apr 2013
                      • 4691

                      man thats really good you guys can spot that. I thought that was the lighting on the edge of the primer, not a crimp ring.
                      Retired Account

                      Comment

                      • #12
                        Rimack
                        Member
                        • May 2013
                        • 163

                        Crimped primer pockets. Ream those suckers!
                        YouTube - TheRightShooter

                        Comment

                        • #13
                          bsumoba
                          Veteran Member
                          • Sep 2012
                          • 4217

                          i use a hand primer to mitigate reasons such as this. feeling the correct amount of pressure to properly seat a primer is important to me as it tells me a lot about my brass such as loose primer pockets, crimped primer pockets, and could also tell me about my loads and whether or not it is putting a beating on the brass.
                          Visit- www.barrelcool.com
                          The Original Chamber Flag and Barrel Cooler in 1
                          Instagram: barrelcool_

                          Comment

                          • #14
                            gomatty
                            Member
                            • Aug 2012
                            • 300

                            It definitely felt different on the press. I'm sure I'll be able to catch them before seating the primer, either on press or with a visual inspection. I had another two unprimed that were crimped so I reamed them. Thanks for all the input. The ones that I primed are flush and kept their shape for the most part. Is there any danger in shooting them?
                            "Anybody can do it...with tools" - Raisin' Rey

                            Comment

                            • #15
                              klewan
                              Veteran Member
                              • Jun 2011
                              • 3031

                              OP, if you use range pick up, you have to ream out the primer pocket, 100%. Otherwise, you get priming issues like what you have. Reaming is just a quick touch to remove the crimp; it is NOT removing .060". It's just the corner getting chamfered.

                              I found out the hard way about crimped brass and priming; had the first priming failure on my Loadmaster in 6K rounds because of crimping. So all the range PU gets the primer knocked out and then 100% reamed. No more problems. If you rely on a visual inspection, some will slip by. Only way to be sure is ream all of them.

                              Comment

                              Working...
                              UA-8071174-1