Unconfigured Ad Widget

Collapse

9mm issues

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • IdahoShooter
    Member
    • Feb 2013
    • 126

    9mm issues

    Hey all,

    I've recently started reloading 9mm and I'm having, what I think, is an unusual issue. When I seat my bullets they come out flat point, they went in as round nose. If I back out the die then the COAL is too long. I've tried backing the die out, backing the seating stem out, belling the case mouths more, basically everything I can think of. I'm using a mixture of brass, none seems better or worse than any other, RCBS carbide dies, xtreme bullets 147gr plated.

    Any ideas? Any and all help would be greatly appreciated! Thanks!
  • #2
    'ol shooter
    Veteran Member
    • Mar 2011
    • 4646

    Did your dies come with two seating stems? If not, it sounds like it has the incorrect one installed. It should not touch the bullet anywhere but the ogive, in other words, be tubular in appearance. From your description it might have a semi-wadcutter stem installed, flat with a lip in appearance.
    sigpic
    Bob B.
    (\__/)
    (='.'=)
    (")_(")

    Comment

    • #3
      Pablo5959
      Senior Member
      • Jan 2013
      • 1289

      +1 on the wad cutter die.

      Comment

      • #4
        IdahoShooter
        Member
        • Feb 2013
        • 126

        It came with 2 stems, .38 spl and 9mm and I have verified that the 9mm stem is in there. The 9mm stem that is in the die is labeled "9mm TMJ" and after doing some searching I couldn't seem to find any replacement stems, maybe my google-fu just sucks.

        Comment

        • #5
          rodsvet
          Member
          • Apr 2013
          • 225

          Doesn't matter if it's 9mm or 38. If it's not a round nose stem, it can flatten the nose. Rod

          Comment

          • #6
            rsrocket1
            Veteran Member
            • Feb 2010
            • 2774

            147g is an awfully big bullet for 9mm. What is your load of powder? It seems as if you are either running out of room in your case or smashing the nose tip on your bullets. With typical seating force, even a flat tipped seating stem should not flatten a round nose bullet much less a plated one. How "flat-nosed" is it? Can you post a picture?

            Comment

            • #7
              Javi
              Veteran Member
              • Dec 2010
              • 4540

              The same thing happened with my Berry bullets. I re-set it up to make sure I didn't have the die set down too low & I believe I did end up switching to the .38spl one in my RCBS seater die and that did the trick.
              Originally posted by d4v0s
              My girlfriend and i used froglube last night in a pinch and it works great.
              R.I.P. Thomas C.

              Comment

              • #8
                XVIga_Rob
                Senior Member
                • May 2012
                • 2354

                Change the seating plug. You want the seating plug for round nose. It has a concave face vs. flat.

                Comment

                • #9
                  SandDiegoDuner
                  Senior Member
                  • Apr 2009
                  • 526

                  I hope you aren't trying to load "ammoload" brand brass. That stuff has an internal shelf that will prevent seating the bullet too deep. Otherwise what powder and charge weight are you using for these 147 grain pills?

                  Comment

                  • #10
                    IdahoShooter
                    Member
                    • Feb 2013
                    • 126

                    Neither of the 2 plugs that came with the set are perfectly round, both have a slightly flat bit. As for the flattening, it varies as to how much, some are small some look like a slightly scaled down .40 S&W. I know I'm not making a compressed load, it's 4.7gr of HS6. No "ammoload" brand brass. There is about the same amount of pressure as when I load .40 S&W, I'm not hulking the press but it's not soft and gentle either. Again, if someone knows where I can get a perfectly rounded stem please post a link because I can't find ANY stems that are particularly for RN. I've checked Midway, Brownells, Grafs and 3rd Gen Shooting Supply all with no luck.

                    Comment

                    • #11
                      IdahoShooter
                      Member
                      • Feb 2013
                      • 126

                      The rounds feed and shoot just fine, there is no adverse effect that I noticed. Really, I'm not sure if this is that big of an issue, I'm mostly just curious since they still perform.

                      Comment

                      • #12
                        'ol shooter
                        Veteran Member
                        • Mar 2011
                        • 4646

                        Oy Vay...
                        sigpic
                        Bob B.
                        (\__/)
                        (='.'=)
                        (")_(")

                        Comment

                        • #13
                          wild_weasel
                          Senior Member
                          • Dec 2008
                          • 1259

                          It sounds like the wrong seating stem in in your seating/crimp die. If you take it out it should have a concaved peofile on the tip.
                          sigpic
                          Towards thee I roll, thou all-destroying but unconquering whale; to the last I grapple with thee; from hell's heart I stab at thee; for hate's sake I spit my last breath at thee.

                          Comment

                          • #14
                            IdahoShooter
                            Member
                            • Feb 2013
                            • 126

                            I just spentthe last hour searching different web sites for replacement seating stems and all I could come up with were Gold Dot specific seating stems and 1 for conical 9mm Makarov. If someone could maybe point me in the right direction or correct me on how to search that would be infinitely more helpful than "get a round one" or "wrong stem" as that has been mentioned several times. I appreciate the help, I really do. I'm a little slow sometimes, too many concussions.

                            Comment

                            • #15
                              Javi
                              Veteran Member
                              • Dec 2010
                              • 4540

                              Try seating a few dummy rounds with the .38 spl stem. I wasn't sure it was going to work but it did end up working for mine.
                              Originally posted by d4v0s
                              My girlfriend and i used froglube last night in a pinch and it works great.
                              R.I.P. Thomas C.

                              Comment

                              Working...
                              UA-8071174-1