Unconfigured Ad Widget

Collapse

Reloading Beowulf Cutting Edge Bullets

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Pupuslinger
    Member
    • Jul 2012
    • 133

    Reloading Beowulf Cutting Edge Bullets

    I just bought some Cutting Edge Bullets for my Beowulf because I needed some lead free ammo for hunting. Does anyone have any load data on 400g solid copper bullets? I have been using Lil'Gun powder with good results.

    I have loaded some Hornady xtp and ftx, but I am sort of new to reloading. I am not sure how loads from one 400g bullet differ from another 400g bullet. Say a hollow point and a FMJ. Could I just pick a 400g bullet and use that load? They were kind of pricey so I only have 50 to work with.
    "anything worth putting a hole in is worth putting a big damn hole in"

    Beowulf
  • #2
    jwb28
    Senior Member
    • Oct 2009
    • 568

    Originally posted by Pupuslinger
    I just bought some Cutting Edge Bullets for my Beowulf because I needed some lead free ammo for hunting. Does anyone have any load data on 400g solid copper bullets? I have been using Lil'Gun powder with good results.

    I have loaded some Hornady xtp and ftx, but I am sort of new to reloading. I am not sure how loads from one 400g bullet differ from another 400g bullet. Say a hollow point and a FMJ. Could I just pick a 400g bullet and use that load? They were kind of pricey so I only have 50 to work with.

    I have never reloaded the Beowulf, or used cutting edge bullets. That said you can get in trouble swapping components sometimes. The bullets may weigh the same, but copper will be longer, so it may sit deeper in the case. That will reduce case capacity and may raise pressure quickly.
    If your not sure, it's best to stick to the data from a manual and not switch stuff.
    You could call cutting edge and ask them if they have data for the Beowulf.

    Comment

    • #3
      Pupuslinger
      Member
      • Jul 2012
      • 133

      These bullets do seem long. I better make sure before I experiment...thanx.
      "anything worth putting a hole in is worth putting a big damn hole in"

      Beowulf

      Comment

      • #4
        Pupuslinger
        Member
        • Jul 2012
        • 133

        Emailed Cutting Edge Bullets and they got back to me right away with load data and pictures for all there .500 bullets. If someone happens upon this thread, pm me and I will email data.
        "anything worth putting a hole in is worth putting a big damn hole in"

        Beowulf

        Comment

        • #5
          elhefe50ss
          CGSSA Coordinator
          • Aug 2011
          • 431

          I load alot of lead and powder coated stuff in my beowulf . If I can help pm me

          Sent from my SCH-I605 using Tapatalk

          Comment

          • #6
            Lead_Rain
            Member
            • Sep 2008
            • 93

            I envy your Lil'Gun...

            Been trying to get Lil'Gun and RL7 for months for my 400 grain Sierra flat points.

            Comment

            • #7
              Whiterabbit
              Calguns Addict
              • Oct 2010
              • 7602

              Originally posted by Pupuslinger
              I am not sure how loads from one 400g bullet differ from another 400g bullet. Say a hollow point and a FMJ. Could I just pick a 400g bullet and use that load? They were kind of pricey so I only have 50 to work with.
              They generally don't vary. There will always be some performance differences, but it's almost always within the noise of the existing load data, from start to max. Remember, YOUR GUN might show pressure signs with a near starting load. I don't know your gun. Good to keep that in mind when experimenting in new territory.

              The exception is lead free bullets. I've always found that the practical maximum for lead free happens at a lower powder charge. When I develop for lead free and no data exists (because it never does), I go something like this:

              1. Start with the closest bullet I can find for load data.
              2. pick candidate powder.
              3. Google-search candidate powder for quirks. Does it like empty space in the case? does it NOT TOLERATE downloading? temp sensitive? require magnum primers? What do I need to know about this powder?
              4. Start loading. If I can, back off from the starting load a smidge and work up looking for pressure. Use what I learn about the powder for loading. For example, AA#9 does not tolerate empty space in the case. To back off from starting loads, the bullet needs to go in deeper. If this demands single loading, that's OK for now. I'm learning the load performance, not trying to make everything work in one shot.
              5. find the accuracy node.
              6. fine tune for feeding if needed. if you shoot semi auto you may need to fine tune for cycling? not my area of expertise.

              If you have no load data, manufacture it. Keep your head screwed on and some common sense about you and you'll be fine. We're all adults here.

              Comment

              Working...
              UA-8071174-1