Unconfigured Ad Widget

Collapse

Squib question for the experts

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • TransplantTexan
    Senior Member
    • Aug 2012
    • 890

    Squib question for the experts

    Almost goes without saying but new to reoading so had a question. All 200 have gone bang and put a hole in the paper with one exception.

    I was shooting my 1911 using 185 gr lswc, 6.6 gr Power Pistol and I had a squib. This caused a FTE and when I pulled the slide back to eject the casing I noticed it was covered in soot. These two things made me go HMMMMM. Checked and sure enough there was the squib. I field stripped and then removed the lead from the barrel and finished off shooting the reloads with no issues.

    Being new, I like to think I'm a little on the cautious side on my procedures. I batch process 50 rounds at a time with a RCBS single stage. Tumble, inspect, decap and size, prime, charge (measuring each load on the scale), seat and crimp. Load, Shoot, Repeat.

    I've looked at the brass and no splits or damage, however I noticed that the Primer is not flush with the casing. This leads me to think that I might not have fully seated this one. Could this have caused the squib? I would like to think I check each round after I put the primer in but I may have missed one.

    While obviously you can't say with absolute certainty the cause, is this at least one scenario.

    Thanks for any input.
    Ignorance is a matter of choice and is usually cured by age, experience and education, but stupid is genetic in nature, and incurable.
  • #2
    Ferrum
    Janitors Mop
    CGN Contributor - Lifetime
    • Aug 2011
    • 4431

    Maybe the case didn't have powder or only a partial charge? This would definitely cause a FTE and leave the lead in the barrel.

    Comment

    • #3
      JagerDog
      I need a LIFE!!
      • May 2011
      • 15885

      Well short or absent of powder. Really no other options in 45.

      Not uncommon to back a primer out a bit when there's not enough pressure to expand the case to the chamber.

      You didn't mention a review of your 50 cases with a flashlight before installing bullets.
      Palestine is a fake country

      No Mas Hamas



      #Blackolivesmatter

      Comment

      • #4
        'ol shooter
        Veteran Member
        • Mar 2011
        • 4646

        I test fired a couple of old primers in a revolver and the primers back right out without powder. Sooo, long story short, LOOK into your cases before you load anything. Glad you spotted it before you broke another shot, that would have been ugly.
        sigpic
        Bob B.
        (\__/)
        (='.'=)
        (")_(")

        Comment

        • #5
          mif_slim
          I need a LIFE!!
          • Apr 2008
          • 10089

          Yup. Lots of soot most likly no powder. Case didnt expand so the carbon from the primer has to go somewhere since a bullet is lodged in the barrel. That somewhere is the chamber.
          Originally posted by Gottmituns
          It's not protecting the rights of the 1%, it's IMPOSING new laws because of the 1%.

          Comment

          • #6
            BigBronco also not a Cabinetguy
            Calguns Addict
            • Jul 2009
            • 7084

            Welcome to the club.
            Definitely missed the powder.
            "Life is a long song" Jethro Tull

            Comment

            • #7
              damndave
              I need a LIFE!!
              • Oct 2008
              • 10858

              Sounds like a missed or low powder charge. But good to see you did the right thing when something did not feel right.

              Comment

              • #8
                mindwreck
                Member
                • Apr 2011
                • 372

                definitely No powder.

                Not enough pressure to seal the casing against the chamber so soot comes out and around the casing and chamber

                same for the primer. Not enough pressure to seal it against the primer pocket. so it slips out a little.

                Comment

                • #9
                  noylj
                  Senior Member
                  • Oct 2010
                  • 713

                  Did you have lead in your barrel as in barrel leading from shooting improperly sized bullets or are you calling the bullet itself "lead?"
                  IF there was no powder, then things are "fine." The "problem" is if it was a partial charge and the rest of the charge made it into another case.
                  Frequently, a cast lead bullet will have enough "speed" just from the primer to make it out the barrel. Jacketed bullets will always be stuck 1-3" into the barrel.

                  PS: the are no casings in reloading. They are cases.
                  Casings go around windows or are used to make sausage.

                  Comment

                  • #10
                    G-forceJunkie
                    Calguns Addict
                    • Jul 2010
                    • 6530

                    Are you using loading blocks? You need to be. Charge 50 cases. Then look down each row with a flashlight and see that there is powder in ever one, and they all are at the same level. Then double check by looking in the case again as you set a bullet on each one. Reloading is about precision and consistancy. You need to work a system that leaves no room for error, and every check has a cross check. Then work that system every time.

                    Comment

                    • #11
                      uhlan1
                      Calguns Addict
                      • Aug 2012
                      • 6217

                      Yea, no powden charge and the primer merely pushed it into the barrel. Glad you had your wits about you and STOPPED
                      "Hence it happened that all the armed prophets conquered, all the unarmed perished." - Niccolo Machiavelli

                      Comment

                      • #12
                        HighLander51
                        Banned
                        • Feb 2010
                        • 5144

                        The Perfect Squib.....


                        Comment

                        • #13
                          Germz
                          Vendor/Retailer
                          • Apr 2013
                          • 4691

                          a pushed out primer is a sign of overpressure, but is also common in a squib. In a squib, there is too little powder which causes it all to ignite at once across the top versus a regulated burn throughout from one end to the other..like a fuse.. (as it should be), this causes a minimal, but high pressure spike and can push primers out a little.

                          are you making match ammo? why do you scale check every charge? In this case I guess you missed one, but a visual check could have mitigated that.

                          invest in a decent powder measure, as anything over $40 will be rated +/- .01gr (unless you get a chargemaster or the like).
                          Retired Account

                          Comment

                          • #14
                            Malthusian
                            Veteran Member
                            • May 2010
                            • 4133

                            definitely use a flashlight

                            personally, I don't like loading blocks, at a minimum (2) loading blocks so you can transfer from one block to the other as you check each round

                            I have never felt comfortable using loading blocks
                            "While it may come as a surprise to the authors of the legislation, most semi-automatic pistols do in fact come with a pistol grip"
                            Malthusianism is the idea that population growth is potentially exponential while the growth of the food supply is arithmetical at best.

                            Comment

                            • #15
                              TransplantTexan
                              Senior Member
                              • Aug 2012
                              • 890

                              Thanks for all the responses. Seems like the consensus is light or no charge. I do use two loading blocks moving the rounds from one to the other. I thought I used a flashlight to check all the cases for powder but obviously missed one. I'll definitely be double checking (if not triple checking) gong forward.

                              Gremz, I've been measuring each load here in the beginning just to reinforce the procedure in my mind.

                              I have a lee powder measure that I have been using as well as a used measure that I acquired a few weeks ago. In fact if any one knows anything about the below photo I'd appreciate any info. It seems to be a little heavier and better made than the lee. It has a brass measuring cylinder which adjusts via 2 screws. I believe it was used on a Hornady Projector Press by the previous owner.
                              [IMG][/IMG]

                              Noyjl, I used lead semi wad cutters , hence the 'lead' term.

                              Again thanks everyone for the information and taking the time to 'educate' me even more. Can't be a bad day -- I've learned something new!

                              Looking forward to loading up some more rounds.
                              Ignorance is a matter of choice and is usually cured by age, experience and education, but stupid is genetic in nature, and incurable.

                              Comment

                              Working...
                              UA-8071174-1