Taking my fist ever 100 reloads of 223 to the range tomorrow.. is it natural to be nervous? Lol kinda scared not gonna lie
Unconfigured Ad Widget
Collapse
|
|
|
|
|
|
|
|
first reloads..
Collapse
X
-
as long as a book was followed as a guide ,everything will be fine.no worries...just turn your head as the trigger is sqeezed.Last edited by highpower790; 08-04-2013, 4:54 PM.Keep it simple!Comment
-
I think it's normal to be nervous over your first loads. As stated earlier, that's a lot of rounds for a first batch. I only load that many when I have a load that is proven.Comment
-
I loaded them to the book.. didnt play with anything.. all my measurements are good.. some a bit under.. I am taking 50 but sure as hell not firing all of them... I am just a tad bit worried about the little things.. like if I crimped them correctly and seated them correctly.. things like that.. i might be overreacting.. I will just be bummed out blowing up my brand new AR upper lol"An armed society is a polite society"
Comment
-
Don't need to crimp for 223 for AR, neck tension will hold the bullet in place. As for the load, did you do the minimum, maximum or midway? Did you try a ladder test where you started at minimum and increase .3 or .5 grains each 5 or 10? I'd shoot them all so you have a feel for them, and it gives you more brass to start the process over with. Get a bull-eyes printout and see how accurate your current loads are. Maybe you were lucky and your gun loves what you have.Comment
-
I used the lee FCD and i did a light squeeze... my starting load was 19.2, max was 21.9... I did 23ish at 20.3 and rest at 20.5.. defiently didnt come too close to the max load.. ill give all of them a shotDon't need to crimp for 223 for AR, neck tension will hold the bullet in place. As for the load, did you do the minimum, maximum or midway? Did you try a ladder test where you started at minimum and increase .3 or .5 grains each 5 or 10? I'd shoot them all so you have a feel for them, and it gives you more brass to start the process over with. Get a bull-eyes printout and see how accurate your current loads are. Maybe you were lucky and your gun loves what you have."An armed society is a polite society"
Comment
-
Having doubts is the smart thing, but if you followed the manual things will be fine. I have been at this awhile and still wonder at times if I did everything correct. you are entering into a great part of the hobby, the ability to tailor the ammo to the weapon and save money doing it. the next phase will be casting your own boolits.Comment
-
Print a few of these out, and test out each load in 3 shot groups. Did you write down your load details? 19.2 to 21.9 is a decent spread in powder and you should begin to see some spreads based on what your barrel likes. What powder did you use?Comment
-
don't need to crimp, but if you have a double feed well....Don't need to crimp for 223 for AR, neck tension will hold the bullet in place. As for the load, did you do the minimum, maximum or midway? Did you try a ladder test where you started at minimum and increase .3 or .5 grains each 5 or 10? I'd shoot them all so you have a feel for them, and it gives you more brass to start the process over with. Get a bull-eyes printout and see how accurate your current loads are. Maybe you were lucky and your gun loves what you have."Adversity Introduces Us To Ourselves"
sigpicComment
-
Not the best ladder I've seen, but you'll be OK. Just using up components faster than need be. I assume you tested that they chamber and fit the mag.Palestine is a fake country
No Mas Hamas
#BlackolivesmatterComment
Calguns.net Statistics
Collapse
Topics: 1,870,791
Posts: 25,176,024
Members: 358,862
Active Members: 5,396
Welcome to our newest member, 1776 Arms.
What's Going On
Collapse
There are currently 38176 users online. 45 members and 38131 guests.
Most users ever online was 239,041 at 11:39 PM on 02-14-2026.

Comment