Unconfigured Ad Widget

Collapse

Dillon 1200 Accuracy Question

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bearstatearmory.com
    Vendor/Retailer
    • Mar 2010
    • 523

    Dillon 1200 Accuracy Question

    I set up my trim die using the L.E. Wilson case gauge and when I trim, I average about 1/3 - 1/4 that are slightly too long (.004) over my 1.750 on the 223. If I run them through again, they come out right on the mark, any suggestions?
  • #2
    joelogic
    Calguns Addict
    • May 2008
    • 6597

    1. 4 thousands isn't much.
    2. If the die is camming over there should be no room for any variation.
    3. I am using Mitutoyo digital calipers and I hit the mark every time.
    4. Why trim to 1.750"? I find most once fired brass much shorter so I trim to 1.735".
    Micro/Mini Reflex Red Dot Sight Mount for the M1, M1a/M14 platform

    Comment

    • #3
      EL_NinO619
      Senior Member
      • Sep 2010
      • 1519

      Originally posted by joelogic
      1. 4 thousands isn't much.
      2. If the die is camming over there should be no room for any variation.
      3. I am using Mitutoyo digital calipers and I hit the mark every time.
      4. Why trim to 1.750"? I find most once fired brass much shorter so I trim to 1.735".
      se carga el diablo de la pistola...
      .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
      On 2 Hornady LnL AP & Dillon Super 1050

      Comment

      • #4
        tiller
        Senior Member
        • Jun 2011
        • 794

        Do not trim to 1.735...

        Set the trimmer to 1.752... It has a variance of .003 I never see over always under...

        Soo the highest I trim is 1.752 which is rare.. And the lowest of 1.749...

        8 out of 10 read 1.7495 to 1.750 others being 1.751
        Last edited by tiller; 07-27-2013, 11:18 AM.
        .223 & .308 brass processing

        Comment

        • #5
          bearstatearmory.com
          Vendor/Retailer
          • Mar 2010
          • 523

          Originally posted by tiller
          Do not trim to 1.735...

          Set the trimmer to 1.752... It has a variance of .003 I never see over allays under...

          Soo the highest I trim is 1.752 which is rare.. And the lowest of 1.749...

          8 out of 10 read 1.7495 to 1.750 others being 1.751
          This is where I'm at now, except about 1/4 - 1/3 are 1.754-1.756 and I'm too OCD to allow that to slide; therefore, I measure and headspace check every case until I'm satisfied. I'm just trying to figure out these extra cases that are a little longer

          Sent from my DROID RAZR HD using Tapatalk 4 Beta

          Comment

          • #6
            CSACANNONEER
            CGN/CGSSA Contributor - Lifetime
            CGN Contributor - Lifetime
            • Dec 2006
            • 44094

            For precision of +/- 0.001" get a Giraud. You asked for suggestions and that's mine. BTW, there's a difference between "accuracy" and "precision".
            NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
            California DOJ Certified Fingerprint Roller
            Ventura County approved CCW Instructor
            Utah CCW Instructor


            Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

            sigpic
            CCW SAFE MEMBERSHIPS HERE

            KM6WLV

            Comment

            • #7
              tiller
              Senior Member
              • Jun 2011
              • 794

              Originally posted by CSACANNONEER
              For precision of +/- 0.001" get a Giraud. You asked for suggestions and that's mine. BTW, there's a difference between "accuracy" and "precision".
              What people don't understand is that it headspaces off of the shoulder... So if you use different headstamps plus range pickup. Your going to be screwed...


              Not every chamber is the same... And you may think " oh yea but I bump the shoulder to the same spec after sizing" it's still NOT the same fire formed case and you will see a difference...
              .223 & .308 brass processing

              Comment

              • #8
                CSACANNONEER
                CGN/CGSSA Contributor - Lifetime
                CGN Contributor - Lifetime
                • Dec 2006
                • 44094

                Originally posted by tiller
                What people don't understand is that it headspaces off of the shoulder... So if you use different headstamps plus range pickup. Your going to be screwed...


                Not every chamber is the same... And you may think " oh yea but I bump the shoulder to the same spec after sizing" it's still NOT the same fire formed case and you will see a difference...
                Most people do understand that when mixed headstamps and range pick up brass get FL sized without adjusting the sizing die being adjusted, the shoulder is in the same place and trimming them with a trimmer which uses the shoulder as a datum point will result in very precisely trimmed brass which measures within 0.001". I sure hope you can come to understand that you are completely wrong. You don't get screwed. You get FL sized brass with an extremely consistent OAL. If you are stupid enough to try to mix FL sized brass with fireformed neck sized brass, yea, you're screwed and really shouldn't be trying to reload in the first place.

                BTW, I and a few others I know have shot .4moa groups at 1000 yards (documented by match results) using FL sized mixed headstamped brass trimmed on a Giraud trimmer which, like the Dillion, indexes off the shoulder.
                Last edited by CSACANNONEER; 07-27-2013, 2:54 PM.
                NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                California DOJ Certified Fingerprint Roller
                Ventura County approved CCW Instructor
                Utah CCW Instructor


                Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                sigpic
                CCW SAFE MEMBERSHIPS HERE

                KM6WLV

                Comment

                • #9
                  tiller
                  Senior Member
                  • Jun 2011
                  • 794

                  Originally posted by CSACANNONEER
                  Most people do understand that when mixed headstamps and range pick up brass get FL sized without adjusting the sizing die being adjusted, the shoulder is in the same place and trimming them with a trimmer which uses the shoulder as a datum point will result in very precisely trimmed brass which measures within 0.001". I sure hope you can come to understand that you are completely wrong. You don't get screwed. You get FL sized brass with an extremely consistent OAL. If you are stupid enough to try to mix FL sized brass with fireformed neck sized brass, yea, you're screwed and really shouldn't be trying to reload in the first place.

                  BTW, I and a few others I know have shot .4moa groups at 1000 yards (documented by match results) using FL sized mixed headstamped brass trimmed on a Giraud trimmer which, like the Dillion, indexes off the shoulder.
                  The dillon does not index off of the shoulder... You adjust the trimmer to the oal that you want... Also you CAN size in the die they are 2 separate things...

                  I am in no way knocking the giraud.... But i would really be interested in seeing your data on your 1000 yard testing...
                  .223 & .308 brass processing

                  Comment

                  • #10
                    CSACANNONEER
                    CGN/CGSSA Contributor - Lifetime
                    CGN Contributor - Lifetime
                    • Dec 2006
                    • 44094

                    OK, I thought the Dillion indexed off the shoulder. I can admit I was wrong about that. I ajust the Giraurd to the OAL I want too.

                    No data on testing because, there hasn't been any "testing" just results of sanctioned matches. The very last group I shot at the FCSA sanctioned match at Coalinga this year was under 5". Also, my rifle and ammo went to the World Championships where DisarmedMarksman shot it. His last record group was 4 1/2" If you really want to see the results for either match, I could post them without any names. But, then you'ld still be taking my word for it. So, if you really need confirmation, I can meet you locally (LA/Ventura county boarder) where you can review the results and check my ID at the same time. Believe me, I don't tell stories about my shooting that can't be verified with hard documentation. Hell, you're more than welcome to PM DisarmedMarksman and ask him or PM 50BMGBOB and ask him. He is the match director for the Coalinga match and has or can get the results from the World Championships.
                    NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                    California DOJ Certified Fingerprint Roller
                    Ventura County approved CCW Instructor
                    Utah CCW Instructor


                    Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                    sigpic
                    CCW SAFE MEMBERSHIPS HERE

                    KM6WLV

                    Comment

                    • #11
                      Davisje011
                      Senior Member
                      • Feb 2012
                      • 556

                      The Dillon does not index, in fact it IS a small base resizing die. I have had very consistent oals with it. The real variation comes with the toolhead rattling around. Before using the 1200clamping down the tool head will help with accuracy. That being said, I've experienced a +/- .002 with mine, no big deal at all. I mean, its really a tiny length if you get down to "brass" tacks...
                      Brass, Brass, and Brass for Sale!!!!!!
                      http://www.calguns.net/calgunforum/s...8#post12109638

                      Comment

                      • #12
                        bearstatearmory.com
                        Vendor/Retailer
                        • Mar 2010
                        • 523

                        I guess I just don't understand why when I run the longer ones through all together they trim fine. Why dont they trim the first time?

                        Sent from my DROID RAZR HD using Tapatalk 4 Beta

                        Comment

                        • #13
                          tiller
                          Senior Member
                          • Jun 2011
                          • 794

                          Originally posted by bearstatearmory.com
                          I guess I just don't understand why when I run the longer ones through all together they trim fine. Why dont they trim the first time?

                          Sent from my DROID RAZR HD using Tapatalk 4 Beta
                          Are you completely hitting the bottom of the pull? When. You pull the handle it should come to an abrupt stop. Use the same motion every time and you should see the same results
                          .223 & .308 brass processing

                          Comment

                          • #14
                            bearstatearmory.com
                            Vendor/Retailer
                            • Mar 2010
                            • 523

                            Originally posted by tiller
                            Are you completely hitting the bottom of the pull? When. You pull the handle it should come to an abrupt stop. Use the same motion every time and you should see the same results
                            Yes I am

                            Sent from my DROID RAZR HD using Tapatalk 4 Beta

                            Comment

                            Working...
                            UA-8071174-1