Unconfigured Ad Widget

Collapse

30-06

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • lincoln45
    Member
    • Jan 2012
    • 379

    30-06

    looking for ideas on a powder weight....

    using H414, same powder i use in my 7mm-08
    165 grn Hornady SST
    Remington 9.5 primers
  • #2
    Rock6.3
    Senior Member
    • Nov 2010
    • 2431

    Here you go, from the Hodgdon reloading webpage:
    Attached Files

    Comment

    • #3
      lincoln45
      Member
      • Jan 2012
      • 379

      Originally posted by Rock6.3
      Here you go, from the Hodgdon reloading webpage:
      i have a couple books..... thanks

      i'm looking for what others have been having good groups with

      its a new savage with a 22" barrel

      Comment

      • #4
        mark501w
        Senior Member
        • Apr 2011
        • 1699

        I have used 3031 4895 748 BLC2 .2230 4320 4350 4064 H380 & I have settled on 4064 & 4350.

        Comment

        • #5
          highpower790
          Veteran Member
          • Jun 2013
          • 3481

          varget works with a wide range of caliburs.in my M1 for 600yds with a 175 sierra or 178 amax ill put 46gr
          Keep it simple!

          Comment

          • #6
            mofugly13
            Senior Member
            • Mar 2009
            • 885

            My hunting load is 49.5gr IMR4895, Remington 9 1/2 primers topped with a 150gr Speer Grand Slam. Shoots MOA out of my 30 year old Rem 700. Chronographs at 2550fps. I have been trying out some heavier charges lately trying to get up to 2900fps, but my groups start opening up. I have killed at least 15 deer with this ;load.
            No government deprives its citizens of rights without asserting that its actions are "reasonable" and "necessary" for high-sounding reasons such as "public safety."
            A right that can be regulated is no right at all, only a temporary privilege dependent upon the good will of the very government
            officials that such right is designed to constrain.

            Comment

            • #7
              rm1911
              Veteran Member
              • Jan 2013
              • 4073

              Originally posted by mofugly13
              My hunting load is 49.5gr IMR4895, Remington 9 1/2 primers topped with a 150gr Speer Grand Slam. Shoots MOA out of my 30 year old Rem 700. Chronographs at 2550fps. I have been trying out some heavier charges lately trying to get up to 2900fps, but my groups start opening up. I have killed at least 15 deer with this ;load.
              IMR4895 x2!!

              Love it. My old sportered 03A3 shoots sub MOA with 48gr and 150's or 165's. I know it's not the hottest load but who cares. It's dead on for way further than I can or will ever shoot a deer at. Plenty enough for me. And 4895 is THE garand powder. So I'm set.
              NRA Life Member since 1990

              They're not liberals, they're leftists. Please don't use the former for the latter. Liberals are Locke, Jefferson, Burke, Hayek. Leftists are progressives, Prussian state-socialists, fascists. Liberals stand against the state and unequivocally support liberty. Leftists support state tyranny.

              Comment

              • #8
                milotrain
                Veteran Member
                • Apr 2011
                • 4301

                Originally posted by lincoln45
                looking for ideas on a powder weight....

                using H414, same powder i use in my 7mm-08
                165 grn Hornady SST
                Remington 9.5 primers
                Well I might have some data for you later. I'm going to be trying some 760 with 168s and Remington 9.5s. But I don't know when I'm going to get to that testing.
                weg: That device is obsolete now. They replaced it with wizards.
                frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                Comment

                • #9
                  highpower790
                  Veteran Member
                  • Jun 2013
                  • 3481

                  milo,
                  is that a ball powder?if so becareful!i only say that because ball powder isambient temperature sensative.watch for flucuations over 70 degrees.
                  Keep it simple!

                  Comment

                  • #10
                    milotrain
                    Veteran Member
                    • Apr 2011
                    • 4301

                    It is ball. Thanks for the warning, I knew about ball's temperature sensitivity but I didn't think it was that extreme. I'll keep the loads light and try not to cook the rounds. It was just the powder that was available, I'll shoot H4859, H4350 or RL17 when it shows up again.
                    weg: That device is obsolete now. They replaced it with wizards.
                    frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                    Comment

                    • #11
                      highpower790
                      Veteran Member
                      • Jun 2013
                      • 3481

                      yeah,im already starting to think about what to do before my varget runs out.but that will be at least two years away,i undertand what you doing.
                      Keep it simple!

                      Comment

                      • #12
                        milotrain
                        Veteran Member
                        • Apr 2011
                        • 4301

                        O'Connell was scolding me for cooking rounds. He said it didn't really matter on a hot day with an AR and stick powder but it was bad practice and one day it will matter when you need the points.
                        weg: That device is obsolete now. They replaced it with wizards.
                        frank: Wait a minute. There are more than one wizard? Is [are?] the wizard calibrated?

                        Comment

                        • #13
                          highpower790
                          Veteran Member
                          • Jun 2013
                          • 3481

                          jim is right.if the round heats up ,the pressure will build.i never close the bolt until im ready to shoot.i might close the bolt for the sighters,but after that...
                          im of the opinion that if i know the chamber is hot,it matters at every shot,wether its hot or cold out.
                          Keep it simple!

                          Comment

                          • #14
                            wtkaiser
                            Senior Member
                            • Oct 2011
                            • 660

                            I have a question about this. Isn't every gun, regardless of caliber, unique in it's likes and dislikes? Therefore what groups well in one gun might group horribly in another gun, even if it's the exact same gun, just a different date of manufacture? And therefore is there any point in asking this question in the first place, except to get a general idea (which the OP would already have since he has two reloading manuals)?

                            Just asking...

                            Comment

                            • #15
                              highpower790
                              Veteran Member
                              • Jun 2013
                              • 3481

                              wtkaiser,
                              your right after all ,what is the point to all these nonsensical rambling posts.all people have to do is read a book and answer there own questions.answer...it provides a outlet for others too put there 2cents in the pot ,for an over analyzed question ,with an abundance of pointless thought...use of guages,dimensions,weight,caliber,bullet,powder,doe s anybody really care?
                              Keep it simple!

                              Comment

                              Working...
                              UA-8071174-1