Unconfigured Ad Widget

Collapse

Machine gun brass

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ExtremeX
    Calguns Addict
    • Sep 2010
    • 7160

    Machine gun brass

    ExtremeX
  • #2
    OldShooter32
    Senior Member
    • Jan 2012
    • 2074

    You won't notice. It might be a little chewed on the head from the extractor but not enough to fret. GI brass (I'm presuming that is what you are getting) is pretty tough.
    "If we make enough laws, we can all be criminals."

    Walnut media for bright brass
    http://www.calguns.net/calgunforum/s...d.php?t=621214

    Comment

    • #3
      hermosabeach
      I need a LIFE!!
      • Feb 2009
      • 19897

      IT depends on the chamber of the MG. Assuming that it was not shot in a fluted chamber, you should not have issues once you full length resize the brass.

      THREAD JACK AHEAD

      As always GI brass is thicker so the internal case capacity is a bit smaller than commercial brass.

      If you have a favorite load for your commercial cases, you might want to back off of the powder charge by a bit and work up to a load for the GI brass.
      Rule 1- ALL GUNS ARE ALWAYS LOADED

      Rule 2 -NEVER LET THE MUZZLE COVER ANYTHING YOU ARE NOT PREPARED TO DESTROY (including your hands and legs)

      Rule 3 -KEEP YOUR FINGER OFF THE TRIGGER UNTIL YOUR SIGHTS ARE ON THE TARGET

      Rule 4 -BE SURE OF YOUR TARGET AND WHAT IS BEYOND IT
      (thanks to Jeff Cooper)

      Comment

      • #4
        the86d
        Calguns Addict
        • Jul 2011
        • 9591

        Originally posted by hermosabeach
        IT depends on the chamber of the MG. Assuming that it was not shot in a fluted chamber, you should not have issues once you full length resize the brass.

        THREAD JACK AHEAD

        As always GI brass is thicker so the internal case capacity is a bit smaller than commercial brass.

        If you have a favorite load for your commercial cases, you might want to back off of the powder charge by a bit and work up to a load for the GI brass.
        I don't think M855 and XM855 are much different... I don't usually run full cases (max load), but I have with .223 and XM855 brass with no noticeable difference (on a XL 650) in powder-spill.

        Comment

        • #5
          Beelzy
          Calguns Addict
          • Apr 2008
          • 9225

          Machinegun brass is not the best for reloading......if you wish more than a few loadings.
          "I kill things for a living, don't make yourself one of them"

          Comment

          • #6
            ferretwithacheeseknife
            Banned
            • Dec 2012
            • 508

            Machine gun chambers tend to be oversize for obvious reasons. So when I have bought military brass fired in a machine gun I have found that I have to trim a lot more cases than range pick-up brass.

            Comment

            • #7
              CSACANNONEER
              CGN/CGSSA Contributor - Lifetime
              CGN Contributor - Lifetime
              • Dec 2006
              • 44094

              MG fired brass will have a shorter life span.
              NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
              California DOJ Certified Fingerprint Roller
              Ventura County approved CCW Instructor
              Utah CCW Instructor


              Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

              sigpic
              CCW SAFE MEMBERSHIPS HERE

              KM6WLV

              Comment

              • #8
                Germz
                Vendor/Retailer
                • Apr 2013
                • 4691

                Originally posted by hermosabeach
                IT depends on the chamber of the MG. Assuming that it was not shot in a fluted chamber, you should not have issues once you full length resize the brass.

                THREAD JACK AHEAD

                As always GI brass is thicker so the internal case capacity is a bit smaller than commercial brass.

                If you have a favorite load for your commercial cases, you might want to back off of the powder charge by a bit and work up to a load for the GI brass.
                Brownells recommends starting loads with NATO brass (lake city, etc) to be 10-15% below published figures.
                Retired Account

                Comment

                • #9
                  Divernhunter
                  Calguns Addict
                  • May 2010
                  • 8753

                  I was given about 18,000+ rounds of full-auto 5.56 brass years ago. I found the some of it just plain would not size in a Rockchucker and RCBS dies. If I forced it I would end up with stuck cases. The stuff that did size(most of it) was a bit tight in my rifle. That comes from the base area being expanded wher the die can do little to help you. I set my dies to bottom out and cam over.
                  That said I used it for many years and gave much of it away to friends also. It works but I would not pay top dollar for any.
                  A 30cal will reach out and touch them. A 50cal will kick their butt.
                  NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
                  SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

                  Comment

                  • #10
                    ke6guj
                    Moderator
                    CGN Contributor - Lifetime
                    • Nov 2003
                    • 23725

                    Originally posted by the86d
                    I don't think M855 and XM855 are much different... I don't usually run full cases (max load), but I have with .223 and XM855 brass with no noticeable difference (on a XL 650) in powder-spill.
                    AFAIK, M855 and XM855 brass is the same thing. it all starts off as M855 when it is made for government. anything that doesn't meet the spec of M855, or if they have overruns, is then tagged as XM855. often you'll see XM855 as being all shiny whereas M855 is more natural and you can see the annealing on the shoulder of the round. civilians want nice and pretty brass where the .mil doesn't want to pay for the added costs (and I think they want to see the annealing to know that it was done).
                    Jack



                    Do you want an AOW or C&R SBS/SBR in CA?

                    No posts of mine are to be construed as legal advice, which can only be given by a lawyer.

                    Comment

                    • #11
                      EL_NinO619
                      Senior Member
                      • Sep 2010
                      • 1519

                      I remember a long time ago, someone at El Cajon FUD Exchange said "if you try a reload machine gun brass, you will blow up your gun." How just reloading a cartridge will blow up a gun is beyond me. But I not only ignored his "sound" advice, I also shot those 7.62's fired out of a Coast Guard M60 machine gun. Some where quite tough to resize. After 5 firings I gave up on them just for safety shake. They worked just fine and I still use MG brass every now and then. Don't be shy on the lube or elbow grease. And I would defiantly use a case gauge, even though some think its a waste of time.
                      se carga el diablo de la pistola...
                      .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
                      On 2 Hornady LnL AP & Dillon Super 1050

                      Comment

                      • #12
                        Che762x39
                        Veteran Member
                        • Aug 2011
                        • 4538

                        I reloaded 7.62 NATO that had been fired in a M-60. I fired it in my FN FAL and the case head would tear off during extration and then I had to use the case removal tool to clear the chamber. It was worser to try to chamber a round in a Remington 700 in .308.

                        I have since moved on to 7.62x39mm.

                        Comment

                        Working...
                        UA-8071174-1