Unconfigured Ad Widget

Collapse

Dented primers

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Banana_hands
    Member
    • Dec 2011
    • 484

    Dented primers

    I loaded my first batch of .223 today and all went slow but well. The only problem I ran into was seating the primers. All little info:
    Lee loadmaster
    Once fired brass (mostly PMC bronze)
    Lee dies
    CCI 400 small rifle primers
    TAC powder (not really relevant but I figured I'd throw any and all info in)

    The problem is most if not all all of the primers ended up with an indentation. My first thought was that I was attempting to seat them too deeply but if I adjust it any more to seat them shallower they sit proud of the case. So I adjusted the bolt that determines primer depth a little at a time but I was unable to seat the primer properly without denting them.
    What am I doing wrong?

    Here's a photo of a dented primer
  • #2
    DeerHunter30.06
    Member
    • Mar 2013
    • 142

    Primer push pin not screwed down all it can be ? what ever is attaching the primer seating device not fit into the press correctly ? Possibly strong arming the seating ? powder or debris in on or around the primer seating area . some off the wall things that could cause such an issue .

    Comment

    • #3
      Colt562
      Calguns Addict
      • Jun 2012
      • 5271

      Maybe the primer wasnt fully set in the primer arm. Could have been canted a little bit.
      Originally posted by bruceflinch
      Tis Better, to be Overworked & Underpaid,
      Than Oversexed & Underlaid...

      Comment

      • #4
        350skylark
        Senior Member
        • Jun 2012
        • 1129

        one time i had a small piece of brass in my little primer cup and all the ammo i loaded had a small indent in it, check for that too, didn't effect the primer going boom though.
        Selling lots of Pistol brass, lots of 38 and 44 mag!
        http://www.calguns.net/calgunforum/s...4#post15935994

        Comment

        • #5
          bohoki
          I need a LIFE!!
          • Jan 2006
          • 20826

          tightpockets you didnt whang it in there hard enough

          Comment

          • #6
            Banana_hands
            Member
            • Dec 2011
            • 484

            Originally posted by Colt562
            Maybe the primer wasnt fully set in the primer arm. Could have been canted a little bit.
            Possible, but that would mean its happening every round.


            Originally posted by bohoki
            tightpockets you didnt whang it in there hard enough
            Not saying you're wrong but if anything I'm the type that would more than likely pull too hard on the handle.


            Originally posted by 350skylark
            one time i had a small piece of brass in my little primer cup and all the ammo i loaded had a small indent in it, check for that too, didn't effect the primer going boom though.
            I'll check for any debris in or around the primer cup area. But the press is brand new and I didn't notice any dirt or debris when I inserted the shell plate.


            Thanks for all the replies. Keep the ideas coming,I'll look into them tomorrow.

            Comment

            • #7
              Bill Steele
              Calguns Addict
              • Sep 2010
              • 5028

              Looks like the ram is not centered and not going up square.

              You have to fully seat the primer or it will not function. It should be a stout pull/push (depending on the type of press), you should be able to feel the primer get seated fully (hard stop).

              I have read where some guys prime off the press when using the Loadmaster. There are a set of videos on Loadmaster tuning somewhere on the internet, I think it was called the Loadmaster Zone or some such thing.
              When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

              Comment

              • #8
                Colt562
                Calguns Addict
                • Jun 2012
                • 5271

                Originally posted by Banana_hands
                Possible, but that would mean its happening every round.
                not necessarily, it could just happen randomly.
                Originally posted by bruceflinch
                Tis Better, to be Overworked & Underpaid,
                Than Oversexed & Underlaid...

                Comment

                • #9
                  Ferrum
                  Janitors Mop
                  CGN Contributor - Lifetime
                  • Aug 2011
                  • 4431

                  Debris on the priming ram? Deformed primer ram? Are you sure that all of the spent primer is being removed (make sure decapping pin isn't too far up)?

                  Just throwing some ideas out there...

                  Comment

                  • #10
                    mindwreck
                    Member
                    • Apr 2011
                    • 372

                    My loadmaster does the same thing with CCI primers. Some of your primer pockets must be tighter than others. The primers are slightly rounded so when it pushes in. its just flatten the bottom of the primer a little. Ive made thousands of rounds and never had any issues with any rounds that had this little indent.

                    Comment

                    • #11
                      sdkevin
                      Senior Member
                      • Jan 2013
                      • 2248

                      Another reason I like hand priming.. you catch pocket chamfer/clenliness/square primer insertion at each case.

                      Just another level of QA.
                      After watching WTC Bldg #7 being razed, and considering it's main occupants..

                      I stumbled onto this note while checking advanced weapons..
                      "911 = false flag. WTC 7 was brought down by demolition. 47 floors came down in 6 1/2 seconds - not hit by a plane. Just one of hundreds of absurdities that occurred that day. Wake up".

                      Comment

                      • #12
                        sdkevin
                        Senior Member
                        • Jan 2013
                        • 2248

                        Another reason I like hand priming.. you catch pocket chamfer/clenliness/square primer insertion at each case.

                        Just another level of QA.
                        After watching WTC Bldg #7 being razed, and considering it's main occupants..

                        I stumbled onto this note while checking advanced weapons..
                        "911 = false flag. WTC 7 was brought down by demolition. 47 floors came down in 6 1/2 seconds - not hit by a plane. Just one of hundreds of absurdities that occurred that day. Wake up".

                        Comment

                        • #13
                          Sunday
                          Calguns Addict
                          • Jan 2010
                          • 5574

                          Originally posted by sdkevin
                          Another reason I like hand priming.. you catch pocket chamfer/clenliness/square primer insertion at each case.

                          Just another level of QA.
                          Been loading with a progressive loader since 1991 at about 5,000 rounds at least per year and I don't have any problems. I started loading around 1976 on a RCBS Rockchucker setup and there were no problems with that setup either.
                          California's politicians and unionized government employees are a crime gang that makes the Mexican drug cartels look like a Girl Scout Troop in comparison.

                          Comment

                          • #14
                            Revoman
                            Senior Member
                            • Dec 2007
                            • 2394

                            Yeah, I'm thinking that it's a little debris on the primer ram. Even a single flake of powder can deform the primer like that and it's tough to see a flake of powder because it matches the ram color.

                            Either that, or the ram is not square on the top and has a slightly rough area.

                            Comment

                            • #15
                              wtkaiser
                              Senior Member
                              • Oct 2011
                              • 660

                              I used to get that sort of thing and traced it to two different problems two different times. The first was like they say, debris (powder flake) on the primer tool arm. The second was what the others say, not a straight pull down of the ram (I use a Lee pro 1000.) So now when I use the press to prime I start the priming stroke, then rotate the case and finish the stroke. I can feel it hit bottom that way. Haven't seen the problem since.

                              Comment

                              Working...
                              UA-8071174-1