Unconfigured Ad Widget

Collapse

Dillon 1050

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Zamble
    Senior Member
    • Jul 2011
    • 2354

    Dillon 1050

    Anyone in stockton available to help dial in/teach me about the 1050? I got it all set up ready to rock. But I need help dialing in the dies and powder check.
  • #2
    Corbin Dallas
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • May 2006
    • 6461

    There are a number of YouTube videos to help you.
    NRA Life Member and Certified Instructor: Pistol - Rifle - Shotgun - PPITH - PPOTH - NRA Certified RSO

    WTB the following - in San Diego
    --Steyr M357A1 357SIG
    --Five Seven IOM (round trigger guard)

    Never forget - השואה... לעולם לא עוד.

    Comment

    • #3
      tiller
      Senior Member
      • Jun 2011
      • 794

      Originally posted by Corbin Dallas
      There are a number of YouTube videos to help you.
      Not alot on 1050's it's slim pickin
      .223 & .308 brass processing

      Comment

      • #4
        Colt562
        Calguns Addict
        • Jun 2012
        • 5271

        Serious question: Is this your first press?
        Originally posted by bruceflinch
        Tis Better, to be Overworked & Underpaid,
        Than Oversexed & Underlaid...

        Comment

        • #5
          milw50717
          Senior Member
          • Jan 2006
          • 740

          Originally posted by Colt562
          Serious question: Is this your first press?
          Whole lotta press for a first timer ....

          Comment

          • #6
            milw50717
            Senior Member
            • Jan 2006
            • 740

            Dillon make a DVD that shows setup including dies, powder check and calibre changes.

            Last edited by milw50717; 04-25-2013, 10:33 PM.

            Comment

            • #7
              alfred1222
              Calguns Addict
              • Jan 2010
              • 7331

              Originally posted by milw50717
              Whole lotta press for a first timer ....
              So your reasoning is that he should buy multiple presses as he learns as opposed to buying one??
              Originally posted by Kestryll
              This guy is a complete and total idiot.
              /thread.

              ΦΑ

              Comment

              • #8
                Zamble
                Senior Member
                • Jul 2011
                • 2354

                Yes it is. I realized when I ordered it, there is a high learning curve. The rounds I shoot are 9mm and .223, and I wanted the high output volume of the 1050.

                Comment

                • #9
                  milw50717
                  Senior Member
                  • Jan 2006
                  • 740

                  So your reasoning is that he should buy multiple presses as he learns as opposed to buying one??
                  Most people don't require the full monty 1050 to meet their needs. It's generally easier to start with a more basic model and work your way up. However, not my $$ or my needs.

                  Comment

                  • #10
                    joelogic
                    Calguns Addict
                    • May 2008
                    • 6597

                    Your eyes and shoulder go out before you can hit the max throughput of a 650 for more than an hour. Just saying.

                    Plus, how are going to trim?
                    Micro/Mini Reflex Red Dot Sight Mount for the M1, M1a/M14 platform

                    Comment

                    • #11
                      Colt562
                      Calguns Addict
                      • Jun 2012
                      • 5271

                      Originally posted by Zamble
                      Yes it is. I realized when I ordered it, there is a high learning curve. The rounds I shoot are 9mm and .223, and I wanted the high output volume of the 1050.
                      Not saying you can't do it, it is just a lot of press for a new guy. But not my money so to each his own. I wish you luck and just keep an eye out for good videos, even if it means spending 20 bucks for the one posted above.


                      Originally posted by alfred1222
                      So your reasoning is that he should buy multiple presses as he learns as opposed to buying one??
                      Not that, just maybe starting out with a single stage to get the basics, kind of like jumping straight into a Boeing 787, without flying a cesna first.

                      Originally posted by milw50717
                      Whole lotta press for a first timer ....
                      I agree. But not my money so...
                      Originally posted by bruceflinch
                      Tis Better, to be Overworked & Underpaid,
                      Than Oversexed & Underlaid...

                      Comment

                      • #12
                        tiller
                        Senior Member
                        • Jun 2011
                        • 794

                        I could help but I am in sac....
                        .223 & .308 brass processing

                        Comment

                        • #13
                          milw50717
                          Senior Member
                          • Jan 2006
                          • 740

                          Originally posted by Zamble
                          But I need help dialing in the dies and powder check.
                          Look for XL650 video on youtube. The basic operations for setting the dies and the powder check are going to be the same for the 1050.

                          Comment

                          • #14
                            Zamble
                            Senior Member
                            • Jul 2011
                            • 2354

                            Thanks for the video reference, I actually bought it when I first ordered my press.

                            For the .223 I ordered the Dillon electric trimmer, but I wont receive that for another 3 weeks or so.

                            Comment

                            • #15
                              tiller
                              Senior Member
                              • Jun 2011
                              • 794

                              Originally posted by Zamble
                              Thanks for the video reference, I actually bought it when I first ordered my press.

                              For the .223 I ordered the Dillon electric trimmer, but I wont receive that for another 3 weeks or so.
                              Ahh those are tricky.... But once dialed in it makes you smile because it trims so fast and easy
                              .223 & .308 brass processing

                              Comment

                              Working...
                              UA-8071174-1