Unconfigured Ad Widget

Collapse

45acp headspace

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Zorgnot
    Member
    • Feb 2012
    • 488

    45acp headspace

    So I've been reloading do a while and haven't had issues with my XD feeding my loads. I recently got a Sig 1911 and I'm having failure to feed on almost every round. I've been using the Lyman reloading manual 49th edition I think.

    What I'm thinking is I may have to crimp the brass a little to get it to feed properly but the book says no roll crimping only a slight taper crimp.

    Any ideas? Am I even on the right track. The brass I'm using is once fired of various brands.
  • #2
    Bill Steele
    Calguns Addict
    • Sep 2010
    • 5028

    Originally posted by Zorgnot
    So I've been reloading do a while and haven't had issues with my XD feeding my loads. I recently got a Sig 1911 and I'm having failure to feed on almost every round. I've been using the Lyman reloading manual 49th edition I think.

    What I'm thinking is I may have to crimp the brass a little to get it to feed properly but the book says no roll crimping only a slight taper crimp.

    Any ideas? Am I even on the right track. The brass I'm using is once fired of various brands.
    I have a SIG 1911 and it is finnicky due to its almost nonexistent freebore.

    What bullet are you loading and what OAL?
    When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

    Comment

    • #3
      gemoose23
      Senior Member
      • Jun 2009
      • 1079

      Additional to Bill's future recommendation/advice once you answer on OAL and Bullet,

      I use one of these during die setup, 1st couple of rounds after caliber change, and on anything my eye questions. (I also randomly QA each box of 50 before labeling and putting away)

      Last edited by gemoose23; 03-26-2013, 10:08 AM.
      Hornady LnL, Dillon Precision, RCBS, Lee Precision and Lyman User
      If You want Match or Leadless hunting Ammo check out Monolithic Munitions Yes I am a shill, friends with the owners.

      Comment

      • #4
        Zorgnot
        Member
        • Feb 2012
        • 488

        I'm away from my stuff now, but I'll post all the details when I get back.

        Comment

        • #5
          C3nt3rMa55
          Member
          • Feb 2012
          • 222

          I reload for my sig with 230gr Rn with an OAL of 1.255 with a very light taper crimp, if using plated any more on the crimp will deform the plating, you want just enough to remove the bell say you belled it out to 1.276 ill crimp down to 1.71-1.72.


          Hope this helps

          Comment

          • #6
            diveRN
            Senior Member
            • Dec 2012
            • 1743



            I'm also interested to hear what bullets and OAL you're using.

            Comment

            • #7
              J-cat
              Calguns Addict
              • May 2005
              • 6626

              This isn't a headspace issue. It is a bullet diameter/OAL issue. The bullet needs to be small enough to enter the chamber throat. Look at your round. see how much bullet shank you have sticking out past the case mouth. this part of the bullet sits in the throat when the round is fully chambered. 99.9% of commercial cast lead bullets are .452" or slightly larger. Some 1911s have .452" throats. As you can see, this causes chambering problems forcing people to reduce OAL. The best solution is to run a SAAMI spec chambering reamer that will open up the throat to .453".

              Sig 1911s have an additional issue in that the throat is short. So even if your bullet fits the throat correctly, you still have to reduce OAL.

              Comment

              • #8
                koehn,jim
                Senior Member
                • Feb 2013
                • 643

                My Lyman book calls for a max case length of .898 and advises no crimp. I use a very slight taper crimp, just enough to straighten the case after bullet seating. I cant speak for a Sig but my Colts all love the rounds.

                Comment

                • #9
                  Zorgnot
                  Member
                  • Feb 2012
                  • 488

                  I'm using 230 gr round nose plated bullets. Forget the brand until I get home later today. My max OAL is what the Lyman book calls for, again can't remember off the top of my head.

                  Comment

                  • #10
                    xbimmers
                    Senior Member
                    • Aug 2008
                    • 1646

                    I suggest you check each round in a chamber checker prior to firing them. Also, the case length of 45 cases should be checked. If they are too long you will have FTF issues. You can fix by over crimping but I do not recommend it.

                    I am betting your cases are to long.
                    Last edited by xbimmers; 03-26-2013, 12:07 PM.
                    How do you travel...

                    Comment

                    • #11
                      diveRN
                      Senior Member
                      • Dec 2012
                      • 1743

                      Originally posted by Zorgnot
                      I'm using 230 gr round nose plated bullets. Forget the brand until I get home later today. My max OAL is what the Lyman book calls for, again can't remember off the top of my head.
                      Here's my .02

                      If you're loading to max OAL, it's probably a bit long. Might load up a few mags each of shortening lengths and retest. Just be sure to stay above the minimum OAL.

                      I load to between 1.255 and 1.265 for those bullets, my book calls max for all bullets at 1.275. The only rounds I load anywhere out that far are lighter JHPs. My Kimber UCII reliably eats 200gr JHP Speer Gold Dots loaded out to 1.28, the P220 not so much.

                      Chances are shortening the round some will fix your problem and it shouldn't affect how they shoot from your HD either.

                      Oh, and checking your loaded diameter with a cartridge gauge and polishing the feed ramp on your Sig couldn't hurt either.
                      Last edited by diveRN; 03-26-2013, 12:10 PM.

                      Comment

                      • #12
                        jameshenry
                        Member
                        • Jan 2011
                        • 327

                        Is it not entering the chamber like in 3 point bind or not final lock up?

                        Comment

                        • #13
                          Zorgnot
                          Member
                          • Feb 2012
                          • 488

                          Final lockup. The slide will be about an eighth inch out of battery.

                          Comment

                          • #14
                            jameshenry
                            Member
                            • Jan 2011
                            • 327

                            I was shooting reloads from a friend(?) that failed to go into battery and checked them with a case gauge=lead was too fat at the zero crimp area. ran them thru my dillon 650 crimp station and then shot them with no problem.

                            Comment

                            • #15
                              Mtn folk
                              Member
                              • Dec 2012
                              • 421

                              might be apples and oranges, but i had a bit of trouble with my .45 Springfield loaded. in hind sight, I wouldn't have attempted a hand load until 500 rounds of factory ammo was run thru it. it is a lot less finicky now than when it was new.

                              but when it was new, this was what i ended up doing.
                              i still check my case length for good practice, but i guess i don't load hot enough to stretch the case. i either lose or step on the case before they need trimming I do like my brass to be all one uniform length.

                              I cast my own round nose and size to .453 in my star lube sizer. I load a few without powder or primer at max oal. I test fit in the cartridge gauge as well as test fit in the barrel when disassembled and shorten if needed. once everything fits nicely i reassemble the pistol, put my dummy rounds in the mag and with the slide locked back and mag in the gun, i hold it up so the left side of the gun is near my right ear, pointing slightly up ward with the muzzle pointed in a safe direction and drop the slide. ( picture how cops in the movies hold their handguns while clearing rooms, pointed up just above their shoulder) I listen for one solid clack of everything locking up quickly. i usually have to shorten it a few thou to find the sweet spot. even if the round chambers and the slide goes into battery, you can tell if it was a struggle or not. once you find the spot, measure the oal and write it down. follow safe and proper load development after that.

                              i hope my red neck system helps.

                              Comment

                              Working...
                              UA-8071174-1