Dillon Super 1050 worth it?

[oddjob]

I started in the world of progressives with a 550 and then went to 1050's. My kids were small back then and family time was my problem. With the 1050 I could do 300 rds in a snap and go to family functions. I have friends who are nothing, but hi-power rifle shooters. They all use a single stage press because they have no need for volume like I do (USPSA). They shoot in one match what I shoot in a single stage. In other words make sure you evaluate your shooting needs and other needs (like family time).

I still run several 1050's and a 550. I found the 550 to be very versatile. You might give some thought to getting two 550's (one set for small primer and the other for large primer). I have friends who do this and they pump out a pretty good amount of ammunition. Changing tool heads and the shell plate on a 550 is a snap. I have a friend who owns a 550, 650 and a 1050. He gave the 650 to his son-in-law and the 1050 sits in his garage. He only loads on the 550.

WARNING; A Super/regular 1050 can be a little touchy. It can be frustrating for someone not used to it. I've learned my 1050's inside and out so I'm comfortable with it, but it took a while. The primer system seems to give me the most problems (when there is one). My 1050's now run like a champ.

Good Luck!

[icedevil]

So 1lb per 7,000 grains means out of 20lbs I can get:
1129rds of 124gr 9mm
608rds of 230gr 45acp
2545 of 55gr 223rem
833rds of 168gr 308win

Check your math. Divide the total number of grains in 20 pounds by the number of grains of powder you will use for your load not the number of grains the bullet weighs. 20 lbs of powder will load you 35,000 rounds of 124 grain 9 mm with a 4.0 grain load not 1,129.

[made2order]

Check your math. Divide the total number of grains in 20 pounds by the number of grains of powder you will use for your load not the number of grains the bullet weighs. 20 lbs of powder will load you 35,000 rounds of 124 grain 9 mm with a 4.0 grain load not 1,129.

Thanks I just found that out. I was TOTALLY OFF and just using bullet weight and NOT the proper grains for each load.

[Revoman]

I would also check with the local fire department as they are the dictators of how much powder one can have in any dwelling, doesn't matter what the State law says. I would advise checking with your insurance company as well as they could not pay out on a fire if they knew you had more than you are supposed to.

[UnknownShooter]

I would also check with the local fire department as they are the dictators of how much powder one can have in any dwelling, doesn't matter what the State law says. I would advise checking with your insurance company as well as they could not pay out on a fire if they knew you had more than you are supposed to.

Firemen dont have any right to "inspect" private homes willy - nilly. After a fire, was it 5 pounds of powder, or fifty?.. the "evidence" will all be gone. I know we're talking about a nanny-state, but sheesh!

[Revoman]

"Firemen dont have any right to "inspect" private homes willy - nilly. After a fire, was it 5 pounds of powder, or fifty?.. the "evidence" will all be gone. I know we're talking about a nanny-state, but sheesh!"

I understand where you're coming from, I'm just saying that there is usually a fire ordinance that dictates how much powder, or anything flammable for that matter, should be stored at a residence.
Even the LGS have that same ordinance from the local fire department. Can they inspect, maybe, maybe not, but that doesn't mean that there is no ordinance.
Different municipalities have different ordinances. If you were to call your local Fire Marshall, I'm sure they would let you know if there is one.
It's kinda like parking on a residential street, there is an ordinance that sez you can't park for more than 72 hours in one spot. Is there a parking police or inspector for this, no, but if it were called in, there would be a citation written or possible towing. Same kinda thing for powder....
Nanny-state, sure. Just sayin'.

[JoshuaS]

The 1050 is harder to change dies out on, and costs quite a bit. It does have a swaging stage, which helps with mil-surp 5.56.

A 650 can do a lot of work, for less money starting with. You can upgrade it of course as time goes on. Starting with all the bells and whistle isn't that much cheaper than the 1050 though

[BigBronco]

One can say the 1050 is a good investment if you wanted to start a brass processing service.

[EL_NinO619]

http://www.dillonprecision.com/#/customize-reloader.html

[EL_NinO619]

If none of those suit your needs, then the 1050 is for you.

[P08]

The 1050 is worth it, but I went with the 650 as it is easier to change calibers and overall the setup costs are lower. The main advantage I see with the 1050 is the primer pocket swaging that is built it, it's a real time saver. The 1050 only has a one year warranty, and that is limited. You will need spare parts on hand, and you will not find many dealers who stock parts for it, not that its a big deal as you can order direct.

[EL_NinO619]

The 1050 does only have a 1 year no BS warranty, but from what I hear and reading everyone's experience with them 1) they pretty much never break 2) Dillon will pretty much cover anything if they know your not a commercial shop.