So a while back I got interested in what a Lee Loader might be able to achieve.
I bought one and have been fooling around at the range with it. I concluded the kit could produce acceptable hunting rounds right out of the box just using the included directions. My first day I was loading rounds that would work for anyone while on a deer or pig hunt.
What I also concluded was the real limitation of the kit was the dipper approach to powder measuring. I like to use extruded powders and the dipper to dipper resolution was about +/- .4gr (after I had perfected my approach). I think that still might work for all but the most demanding applications, if you could get to a custom dipper that dropped the load which took you to the widest node in that component selection, I think what White Rabbit means when he uses the term "Robust". Once I know what works with the components I am using now, I will construct a custom dipper that will drop that "ideal" charge and see if I can do the whole thing at the range with a bottle of powder and a dipper, no weighing at all.
So today I decided to take the dipper out of the equation and do a ladder using IMR 4064, WLR primers, some bulk 150gr FMJ bullets and some "seen better days" Lake City Mil-Surp brass. I dropped and trickled pre-measured amounts of powder and put them in small glass bottles, but otherwise used the Lee Loader and my brass mallet for all the other tasks today. I only did four shot strings as I didn't have enough bottles to load 5 of each rung of the ladder. Once I determine where the promising nodes are I will load 5 at least of each rung.
I only got through about half the ladder before I ran out of time, but the results look promising. I used the same case for each string, changing cases for each successive string. The brass was pretty tired and I started seeing loose primers and gas leakage around the primer pockets by the end of a string. Also, the brass had not been annealed in a while, so I was also concerned work hardening of the necks might hurt accuracy.
All in all, the components I used were pretty modest in capability and with the exception of using the same case within each string and "clocking" the case to the same spot in the die while sizing and in the chamber when shooting, everything else was pretty "McGuyer" in nature. I figured the bulk 150 FMJ would be OK for the 100yds I was shooting today (like I had a choice as my Match bullets are somewhere in the ether still).
My best string came towards the middle of the ladder at 42.8grs of IMR 4064.
Bottom target is this result.

I am pleased with the results so far. I think there may be another wider node on this setup as the upper target represents a half a grain less of IMR 4064. After I finish this ladder and have identified the promising charges, I will go back and measure out another ladder focusing on dialing in the widest node.
My expectation is I should be able to get down in the .3-.4" grouping (at 100 yards) using the components I am right now. After I get really comfortable with what works with this setup, I will go back and start using premium brass, match HPBT bullets (AMAX or SMK's) and some Federal 210M match primers. My goal is to get to .2 MOA while using the Lee Loader at the range.
I will update this thread as I start to dial in this load and also when I start using better components.
Some fun.
I bought one and have been fooling around at the range with it. I concluded the kit could produce acceptable hunting rounds right out of the box just using the included directions. My first day I was loading rounds that would work for anyone while on a deer or pig hunt.
What I also concluded was the real limitation of the kit was the dipper approach to powder measuring. I like to use extruded powders and the dipper to dipper resolution was about +/- .4gr (after I had perfected my approach). I think that still might work for all but the most demanding applications, if you could get to a custom dipper that dropped the load which took you to the widest node in that component selection, I think what White Rabbit means when he uses the term "Robust". Once I know what works with the components I am using now, I will construct a custom dipper that will drop that "ideal" charge and see if I can do the whole thing at the range with a bottle of powder and a dipper, no weighing at all.
So today I decided to take the dipper out of the equation and do a ladder using IMR 4064, WLR primers, some bulk 150gr FMJ bullets and some "seen better days" Lake City Mil-Surp brass. I dropped and trickled pre-measured amounts of powder and put them in small glass bottles, but otherwise used the Lee Loader and my brass mallet for all the other tasks today. I only did four shot strings as I didn't have enough bottles to load 5 of each rung of the ladder. Once I determine where the promising nodes are I will load 5 at least of each rung.
I only got through about half the ladder before I ran out of time, but the results look promising. I used the same case for each string, changing cases for each successive string. The brass was pretty tired and I started seeing loose primers and gas leakage around the primer pockets by the end of a string. Also, the brass had not been annealed in a while, so I was also concerned work hardening of the necks might hurt accuracy.
All in all, the components I used were pretty modest in capability and with the exception of using the same case within each string and "clocking" the case to the same spot in the die while sizing and in the chamber when shooting, everything else was pretty "McGuyer" in nature. I figured the bulk 150 FMJ would be OK for the 100yds I was shooting today (like I had a choice as my Match bullets are somewhere in the ether still).
My best string came towards the middle of the ladder at 42.8grs of IMR 4064.
Bottom target is this result.

I am pleased with the results so far. I think there may be another wider node on this setup as the upper target represents a half a grain less of IMR 4064. After I finish this ladder and have identified the promising charges, I will go back and measure out another ladder focusing on dialing in the widest node.
My expectation is I should be able to get down in the .3-.4" grouping (at 100 yards) using the components I am right now. After I get really comfortable with what works with this setup, I will go back and start using premium brass, match HPBT bullets (AMAX or SMK's) and some Federal 210M match primers. My goal is to get to .2 MOA while using the Lee Loader at the range.
I will update this thread as I start to dial in this load and also when I start using better components.
Some fun.


Comment