Unconfigured Ad Widget

Collapse

Bullet pullers

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 3DGearGuy
    Vendor/Retailer
    • Jun 2012
    • 804

    Bullet pullers

    I've noticed both hornady and rcbs make die mounted collet pullers with a nifty handle to grab a hold of the bullet.

    Does anyone have experience with either? Do they leave marks? Ease of use? I'd imagine there isn't much to it other than tighten collet and yank down on the round but I'd like to hear from someone who's tried it and get an idea for how well they work.

    On a related note....would one be able to pull bullets from surplus ammo and replace with a range safe projectile of the same weight?
    3DGearGuy - 3D printing freedom since 2020! Use code CG10OFF for 10% off all orders of $15 or more!
  • #2
    NoNOS67
    Senior Member
    • Aug 2008
    • 2161

    Originally posted by idlplumb
    I've noticed both hornady and rcbs make die mounted collet pullers with a nifty handle to grab a hold of the bullet.

    Does anyone have experience with either? Do they leave marks? Ease of use? I'd imagine there isn't much to it other than tighten collet and yank down on the round but I'd like to hear from someone who's tried it and get an idea for how well they work.

    On a related note....would one be able to pull bullets from surplus ammo and replace with a range safe projectile of the same weight?
    They work well with jacketed bullets. If the original round was crimped, you may have issues seating a new bullet. Never tried it myself, but I'm sure someone here has.

    Comment

    • #3
      EL_NinO619
      Senior Member
      • Sep 2010
      • 1519

      I just got the Hornady hammer one after my rcbs broke. The Hornady one is way better, the collet system allows you to drop out the case a projectile with out taking the screw cap off. I have never though about buying a press mounted one since I never plan on making that many mistakes or buying someone's reloads.
      se carga el diablo de la pistola...
      .223, .25acp, 25-20win, 9mm, 38spl/.357, 10mm .308, 8mm M, 7mm Rem Mag, 45acp, .475 Wildey mag
      On 2 Hornady LnL AP & Dillon Super 1050

      Comment

      • #4
        m98
        Veteran Member
        • Jul 2005
        • 4088

        Hornady collet puller is the best in my experience. It will pull jacket bullets without damage or markings if setup correctly. And the hornady system is also cheaper than rcbs.
        "Screw U guys, I'm going home"...:the great Eric Cartman

        10mm. Because .45ACP just doesn't cut it anymore. <Trailerparktrash>

        Comment

        • #5
          drdarrin@sbcglobal.net
          Senior Member
          • Feb 2011
          • 2219

          Originally posted by idlplumb
          I've noticed both hornady and rcbs make die mounted collet pullers with a nifty handle to grab a hold of the bullet.

          Does anyone have experience with either? Do they leave marks? Ease of use? I'd imagine there isn't much to it other than tighten collet and yank down on the round but I'd like to hear from someone who's tried it and get an idea for how well they work.

          On a related note....would one be able to pull bullets from surplus ammo and replace with a range safe projectile of the same weight?
          1) I've used both the kinetic and the press mounted RCBS bullet puller. Yes, the press mounted puller will leave marks. You have the right idea on how they work. Even though it leaves marks, as long as the bullet is not seriously deformed (as in mushed), it is still usable. I just wouldn't plan on extremely accurate long range shooting with them.

          2) I have done this same thing, pulling FMJ bullets and replacing them with Spitzer soft points of similar (+- 3 grains) weight. In my case, these were surplus 30-06 rounds from WWII. I used a neck sizer die to resize only the neck before seating the new bullet. You have to be very careful not to spill any powder.

          That said, just because you can do something doesn't mean you should. If I had it to do over again, I wouldn't bother. The cost/time benefit didn't matter to me at the time; I needed hunting rounds and was dirt poor at the time.

          Plus, you want to replace the existing projectiles with range safe projectiles and are concerned about marks on the projectiles you intend to pull? Why the concern? If you intend to reuse the projectiles, why not just leave the rounds alone and purchase the range safe ammo you need? When you reuse the pulled projectiles, they still won't be range safe, will they?
          NRA Life Member
          GOA Life Member
          USMC '71 - '78

          "I am only one; but still I am one. I cannot do everything; but still I can do something; and because I cannot do everything, I will not refuse to do the something that I can do."
          Edward Everett Hale

          Comment

          • #6
            jdmstuff
            Senior Member
            • Jul 2012
            • 761

            I use the RCBS puller and like the fact that I don't get powder everywhere. If done carefully, the bullet doesn't get scratched and can be reloaded. I currently have it mounted up to my rock chucker next to my Dillon "just in case."

            Comment

            • #7
              Bill Steele
              Calguns Addict
              • Sep 2010
              • 5028

              I also have the RCBS collet puller. It can be used with no marks on jacketed bullets, but you have to have exact right collet to pull this off. It will not work on most lead (other than the hardest hard cast). This style puller is great if you have a lot to pull.

              I also have the RCBS hammer style puller. I use it much more frequently (since I broke down and bought one) than the collet puller. Maybe I am making fewer large batch mistakes these days, who knows. If you have neither, get the hammer style first. If you get the RCBS unit, make sure and get a few of the aluminum collars that is the universal shellholder for them. They break down over time, it is nice to have a spare when one goes south. RCBS will replace anything that breaks though, so you only really need a single extra I guess.

              Good luck, have fun.
              When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

              Comment

              • #8
                Vlad 11
                Veteran Member
                • Nov 2009
                • 2961

                I use the RCBS puller. Works great and i dont have any problems with it leaving marks.

                If I get a hard to pull bullet, like a crimped or sealed, I just push it inward a tiny amount. This breaks the seal and it then pops right out when pulled.

                Comment

                • #9
                  3DGearGuy
                  Vendor/Retailer
                  • Jun 2012
                  • 804

                  I just don't completely understand how the hammer style pullers work, anyone?

                  As far as scratching the bullets, I'm not worried about scratching bullets to make range safe ammo, but I figure I'll make mistakes at some point and will have bullets I'll want to pull that I'd reuse.
                  3DGearGuy - 3D printing freedom since 2020! Use code CG10OFF for 10% off all orders of $15 or more!

                  Comment

                  • #10
                    johnny1290
                    Senior Member
                    • Apr 2011
                    • 1598

                    I bought a hammer style bullet puller. It works fine for jacketed or plated 9mm , but not on lead IIRC.

                    I loaded up 100 .223 and needed to pull them. It was such a huge PITA I ended up just using pliers. It marked them a bit but if there was any difference in my plinking with them I don't know what it was. Didn't mark as bad as I figured and 100 times faster.

                    I'll probably just do the same in the future, as that hammering is really for the birds.

                    Comment

                    • #11
                      jdmstuff
                      Senior Member
                      • Jul 2012
                      • 761

                      Originally posted by idlplumb
                      I just don't completely understand how the hammer style pullers work, anyone?
                      Momentum...

                      Place the round in one end and strike on a solid surface.

                      Comment

                      • #12
                        madjack956
                        Veteran Member
                        • Jan 2006
                        • 2617

                        Originally posted by idlplumb
                        I just don't completely understand how the hammer style pullers work, anyone?

                        As far as scratching the bullets, I'm not worried about scratching bullets to make range safe ammo, but I figure I'll make mistakes at some point and will have bullets I'll want to pull that I'd reuse.
                        A collet at one end of the hammer holds the round buy its base inside the hollow hammer. You then hammer it on a hard surface like driving a nail and kinetic energy drives the bullet out of the case into the bottom of the hammer along with all your powder. The hammers have a small piece of sponge in them to soften the landing and keeping your bullet pristine.

                        After using it a few times you get a feel for how hard you need to rap the hammer on the surface to release the bullet.
                        Paralyzed Veterans of America www.pva.org

                        Comment

                        • #13
                          Divernhunter
                          Calguns Addict
                          • May 2010
                          • 8753

                          I have the RCBS hammer and collet style pullers. I do like what I see in the Hornady collet puller. The RCBS collet press mounted works just fine. I have pulled many a bullet with it. The trick when pulling mil ammo since it is crimped and sealed is to set the collet then push the bullet deeper into the case to break the seal etc then work the handle the other way to remove the bullet. You can seat another bullet but I find it better to pull the bullet and the put the powder into another case that I have run into the resize die just enough to have the expander ball true up the brass. I start by using about 100 of the fired brass and resize and prime them first. After that you will always have ones ready to go. Only need to do 50-100 fired cases.
                          The hammer type works because the bullet is heavy and when the motion stops the bullet wants to keep going. Thus comes out of the case.
                          A 30cal will reach out and touch them. A 50cal will kick their butt.
                          NRA Life Member, NRA certified RSO & Basic Pistol Instructor, Hunter, shooter, reloader
                          SCI, Manteca Sportsmen Club, Coalinga Rifle Club, Escalon Sportsmans Club, Waterford Sportsman Club & NAHA Member, Madison Society member

                          Comment

                          • #14
                            slopoke
                            Senior Member
                            • Jan 2010
                            • 509

                            I had to disassemble a few hundred .308 rounds. I bought a RCBS collet puller, because I did not want to use my kinetic puller for that amount of rounds. It worked great, no marks on my bullets. If you don't need to pull a bunch, I'd stay with the kinetic (hammer) type. It will accomodate different calibers. The collet pullers are caliber specific and the collets are approx $11 a piece, the collet puller itself is approx $20. Kinetic types are $15-$20.
                            Last edited by slopoke; 02-07-2013, 4:08 AM.

                            Comment

                            • #15
                              drkphibr
                              Senior Member
                              • Dec 2010
                              • 2466

                              Originally posted by idlplumb
                              I've noticed both hornady and rcbs make die mounted collet pullers with a nifty handle to grab a hold of the bullet.

                              Does anyone have experience with either? Do they leave marks? Ease of use? I'd imagine there isn't much to it other than tighten collet and yank down on the round but I'd like to hear from someone who's tried it and get an idea for how well they work.

                              On a related note....would one be able to pull bullets from surplus ammo and replace with a range safe projectile of the same weight?
                              I use the Hornady puller as well as a kinetic puller. Each for different reasons. Quick one or two bullet removals is usually the kinetic (as long as it's not a SP rifle round as the force on the kinetic tends to mash them a bit). For any volume, it's the Hornady. Very adjustable and precise. Not perfect by any means, but does an excellent job. Collets not available in all sizes, so your mileage may vary.

                              Comment

                              Working...
                              UA-8071174-1