Unconfigured Ad Widget

Collapse

Some reloading questions!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • A.M.
    Senior Member
    • Sep 2012
    • 578

    Some reloading questions!

    Hey all--

    Just got my Hornady LNL in :-)

    I have a handful of questions, if that's ok with you all.

    I am going to be reloading .223, .308, and 40SW

    1) I just purchased a Thumber Model B Tumbler + SS... If I'm doing that, what is the "order" to tumbling with it? People say that it is better to deprime THEN tumble with the SS...

    Don't I need to clean it ahead of time?

    Can I use a vibratory tumbler + walnut media to clean it?

    AKA: Walnut + vibratory >> Deprime/size >> SS Tumble

    Or do you suggest something else?

    If I do the above, is it ok for it to have dust on it from the walnut?

    2) Is it better to use a "neck sizing" die or a "full sizing die"? I have once fired brass (not shot in my rifle). This is related to my 223 loads. What about if I had shot it in my rifle?

    You all rock.
  • #2
    Dark Mod
    Veteran Member
    • Feb 2011
    • 4284

    No need to tumble twice unless your trying to remove lube, which wouldnt really be a problem in your case since your gonna want to deprime before you tumble. I would decap first before SS tumbling so you can get nice and shiny primer pockets. The beauty of SS media is it gets in the flash hole and makes the brass as good as new. I cant think of any reason to use both vibratory and SS.

    Neck sizing is typically used for bolt guns, since autoloaders tend to bulge the case a bit more. If your shooting out of an AR you should probably full length resize every time.

    Comment

    • #3
      NiteQwill
      Calguns Addict
      • Dec 2007
      • 6368

      Dark Mod covered it.

      Deprime when SS tumble. No need to do it twice.

      Neck sizing for bolt guns (I use a neck sizer and manderel by Lee). FL sizing for semi-auto (Dillon). Don't forget to trim, too.

      The fate of the wounded rest in the hands of the ones who apply the first dressing.

      Comment

      • #4
        NiteQwill
        Calguns Addict
        • Dec 2007
        • 6368

        Dark Mod covered it.

        Deprime when SS tumble. No need to do it twice.

        Neck sizing for bolt guns (I use a neck sizer and manderel by Lee). FL sizing for semi-auto (Dillon). Don't forget to trim, too.

        The fate of the wounded rest in the hands of the ones who apply the first dressing.

        Comment

        • #5
          A.M.
          Senior Member
          • Sep 2012
          • 578

          Wait--

          So I just take the dirty cases, lube them, deprime/size, then SS tumble?

          Isn't that bad for the die?

          Comment

          • #6
            NiteQwill
            Calguns Addict
            • Dec 2007
            • 6368

            Originally posted by A.M.
            Wait--

            So I just take the dirty cases, lube them, deprime/size, then SS tumble?

            Isn't that bad for the die?
            No need to lube, get a universal depriming die. Don't use your sizing die.


            The fate of the wounded rest in the hands of the ones who apply the first dressing.

            Comment

            • #7
              A.M.
              Senior Member
              • Sep 2012
              • 578

              So I would need to put that in my LNL, decap, take them out, then do it all over again after cleaning to actually load the bullets?

              Comment

              • #8
                scotty99
                Senior Member
                • Dec 2009
                • 1184

                That depends on how clean you want the primer pockets. If you're loading highly accurate match ammo, yes, deprime then tumble. If you're loading plinking or basic range ammo, tumble first, then resize, prime and load away.

                Comment

                • #9
                  A.M.
                  Senior Member
                  • Sep 2012
                  • 578

                  Is there a "hand deprimer" tool out there?

                  Comment

                  • #10
                    ___M|9||___
                    Senior Member
                    • Jan 2013
                    • 1507

                    no, usually reloaders buy a single stage press and just put their siz deprime die on it, resize and deprime and THEN they put in the ss media and tumble away, OR yuo can just deprime and size on the first stage on your LNL good luck

                    Comment

                    • #11
                      JoshuaS
                      Senior Member
                      • Nov 2012
                      • 1617

                      IIRC, if the brass is not fired out of your gun, you should full length resize even for bolt guns. Once fired in your gun, it will be fire formed for your chamber. Then neck resize if using it in only that gun.

                      You could also get a primer pocket cleaning tool for fairly cheap. So tumble, resize/deprime, and then clean the primer pocket with the tool.

                      Comment

                      • #12
                        Anti-Hero
                        Senior Member
                        • Dec 2009
                        • 1572

                        Originally posted by JoshuaS
                        IIRC, if the brass is not fired out of your gun, you should full length resize even for bolt guns. Once fired in your gun, it will be fire formed for your chamber. Then neck resize if using it in only that gun.
                        ONLY if you're shooting that ammo out of a bolt gun. A semi-auto will need to be full-length sized or you'll run into issues chambering rounds.
                        IPSO FACTO

                        Comment

                        • #13
                          NiteQwill
                          Calguns Addict
                          • Dec 2007
                          • 6368

                          Originally posted by A.M.
                          So I would need to put that in my LNL, decap, take them out, then do it all over again after cleaning to actually load the bullets?
                          Buy 2 (or more) tool heads. Many reloaders use multiple toolheads to get it done. You will have to lube, resize, and tumble (again) any bottleneck cases before loading them anyway.

                          Here is the process:

                          Phase 1:
                          1. Deprime
                          2. SS tumble/clean

                          Phase 2:
                          1. Lube THEN FL resize brass
                          2. If you have ALREADY fired brass in your bolt gun, neck size only
                          3. Trim, chamfer, deburr
                          4. Tumble again to clean lube

                          Phase 3:
                          1. Prime
                          2. Powder
                          3. Seat bullet
                          4. Crimp (Many say it is not necessary, many don't crimp. I don't crimp.)

                          The fate of the wounded rest in the hands of the ones who apply the first dressing.

                          Comment

                          • #14
                            bootcamp
                            Senior Member
                            • Mar 2006
                            • 1019

                            Holy cow, I like it when people spend YOUR money!

                            Once again, overthinking.

                            for pistol brass (no neck):

                            Tumble/clean
                            Deprime/resize
                            powder/prime
                            bullet seat
                            crimp if you desire

                            Rifle brass:

                            tumble/clean
                            lube
                            decap/fl resize
                            trim to spec
                            chamfer/debur if desired
                            neck size (if not already done)
                            powder/prime
                            bullet seat
                            crimp
                            spray and wipe brass with rubbing alcohol OR put loaded ammo into tumbler and tumble the lube off for about 30-45 mins. AND NO, I'VE TUMBLED THOUSANDS OF ROUNDS AND NEVER HAD A ND, NOR HAS IT RUINED THE POWDER INSIDE THE LIVE ROUND.

                            Unless you're planning on killing the next terrorist from 2 miles away, CLEANING THE PRIMER POCKET IS A ABSOLUTE COMPLETE WASTE OF TIME.
                            Last edited by bootcamp; 01-04-2013, 10:04 AM.
                            Originally posted by ar15barrels
                            Lube helps whenever you are trying to get something into a tight hole.

                            Comment

                            • #15
                              bootcamp
                              Senior Member
                              • Mar 2006
                              • 1019

                              Do a search for raymondmillbrae's video post about processing brass. Very simple and easy to follow instructions. Also read ar15barrel's processing brass in bulk tutorial.
                              Originally posted by ar15barrels
                              Lube helps whenever you are trying to get something into a tight hole.

                              Comment

                              Working...
                              UA-8071174-1