Unconfigured Ad Widget

Collapse

416 Barrett reloading issues

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Scar13
    Member
    • Nov 2012
    • 233

    416 Barrett reloading issues

    Rainy day Sunday, so I started working on my 416 reloads again. I have about 40 cases that I have sized and primed, ready for the last step. I weighed 190 grains of powder, set the bullet into the case and began bringing the tool down to seat the bullet. Slowly adjusting the die seating length, measuring, do it again. I kept ending up with 4.55 in length, tried another one till I realized that the bullet was loose in the case. Not sure why the bullet is loose, I don,t think the die crimps the bullet. Any ideas what I am doing wrong?
  • #2
    wtkaiser
    Senior Member
    • Oct 2011
    • 660

    First thoughts are either you have the wrong bullets or you didn't get the sizing die down far enough. By the time you hit the seating die, you should have the neck down far enough. You don't, so measure your bullets and make sure your sizer is correct.

    Comment

    • #3
      CSACANNONEER
      CGN/CGSSA Contributor - Lifetime
      CGN Contributor - Lifetime
      • Dec 2006
      • 44094

      The seating die should crimp, or at least, tighten the neck around the bullet when it is properly adjusted. I'm curious if you are using factory brass? Has it been neck turned? Inside or outside? Who made the dies? Are you using the expander ball that came with your FL sizing dies? While the expander shouldn't be the problem, it might be contributing to it a little.
      NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
      California DOJ Certified Fingerprint Roller
      Ventura County approved CCW Instructor
      Utah CCW Instructor


      Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

      sigpic
      CCW SAFE MEMBERSHIPS HERE

      KM6WLV

      Comment

      • #4
        Whiterabbit
        Calguns Addict
        • Oct 2010
        • 7602

        190 grains of powder, sheesh.

        If you are sure the die does not crimp (or restrict the neck in any way at all), then I'd first look at my expander ball in the resize die. might be oversized. But bottom line, you have one of two issues:

        case tension is getting lost after seating (plastic deformation, strong crimp, etc)
        case tension was never there to begin with (Neck was never sized down then expanded, or was expanded too much after sizing.)

        Comment

        • #5
          Scar13
          Member
          • Nov 2012
          • 233

          The die set I am using is made by Lee Precision. I took another look at my setup and see that the bullet seating die does not come in contact with the bottom die at all, there is probably 3/8" between the two fully possitioned to seat the bullet. I know when I size the brass (Once fired Barrett brass) I make sure that I do a cam over, but have never really concentrated on this in the bullet seating. Are they suppose to touch?
          I measured the bullets and see that the neck size is .413. These are solid brass bullets.
          Thx

          Comment

          • #6
            Whiterabbit
            Calguns Addict
            • Oct 2010
            • 7602

            Do you feel normal resistance during seating? Any indication that neck tension is "right" when you pull the handle to seat the bullet?

            Comment

            • #7
              Scar13
              Member
              • Nov 2012
              • 233

              That is interesting that you ask that question, my son and I were looking at each other during the seating wondering why the process clunked and chunked so much. The bullets do have ribs or cannalures cut into them, and I thought this is what all the clunking was. I have reloaded a bunch (10K) 223, 308, 30-06 rounds and thought I knew what I was doing, but it doesn't seem to be the case this time.

              Comment

              • #8
                CSACANNONEER
                CGN/CGSSA Contributor - Lifetime
                CGN Contributor - Lifetime
                • Dec 2006
                • 44094

                Originally posted by Whiterabbit
                190 grains of powder, sheesh.
                Yea, after seeing that he's using 190 grains, I'm thinking about downsizing to the bastard round that is to big for BR shooting and too small for FCSA matches just to save on powder. I wish I could get away with such a small powder charge.

                Back to the problem. I'm going to assume that you have not neck turned, removed the dreaded donut or any other precision brass prep. So, first back out your seating stem ALL THE WAY. Then, see if the neck will make contact with the die at all. If it does, check to see if you can "crimp" the neck until a bullet doesn't look like it will fit and report back.
                NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                California DOJ Certified Fingerprint Roller
                Ventura County approved CCW Instructor
                Utah CCW Instructor


                Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                sigpic
                CCW SAFE MEMBERSHIPS HERE

                KM6WLV

                Comment

                • #9
                  Whiterabbit
                  Calguns Addict
                  • Oct 2010
                  • 7602

                  well, I was making a tongue in cheek comment there, didn't want to make it a thing. Supposed to have been just in good humor. Maybe I needed a smily to go with it. Though I do see you are in the same mindset as me.




                  Comment

                  • #10
                    Whiterabbit
                    Calguns Addict
                    • Oct 2010
                    • 7602

                    Originally posted by Scar13
                    That is interesting that you ask that question, my son and I were looking at each other during the seating wondering why the process clunked and chunked so much. The bullets do have ribs or cannalures cut into them, and I thought this is what all the clunking was. I have reloaded a bunch (10K) 223, 308, 30-06 rounds and thought I knew what I was doing, but it doesn't seem to be the case this time.
                    my banded solids and TTSX's do the same, but there's good resistance during seating. That's one reason I know my neck tension is right where I want it to be.

                    Comment

                    • #11
                      ChrisGarrett
                      Member
                      • Sep 2011
                      • 200

                      Originally posted by Scar13
                      Rainy day Sunday, so I started working on my 416 reloads again. I have about 40 cases that I have sized and primed, ready for the last step. I weighed 190 grains of powder, set the bullet into the case and began bringing the tool down to seat the bullet. Slowly adjusting the die seating length, measuring, do it again. I kept ending up with 4.55 in length, tried another one till I realized that the bullet was loose in the case. Not sure why the bullet is loose, I don,t think the die crimps the bullet. Any ideas what I am doing wrong?
                      The neck walls are probably thinner on the one case where the bullet is loose. If you have a ball mic, you can measure at three places around the neck and get an idea.

                      Does the Lee die have a crimping step built into it?

                      Even if it does, it might not be enough to offset the lack of constriction being placed on the neck by the sizing die, for cases with thinner neck walls.

                      Chris

                      Comment

                      • #12
                        Scar13
                        Member
                        • Nov 2012
                        • 233

                        I will look at these diffeent suggestions you guys have given me. I have also received some suggestions from the techs at Lee. I will let you know what I find out.

                        Comment

                        • #13
                          CSACANNONEER
                          CGN/CGSSA Contributor - Lifetime
                          CGN Contributor - Lifetime
                          • Dec 2006
                          • 44094

                          If you get really stumped, you're always welcome to bring your dies and brass to my place and we can try to figure out the problem together. While I don't have any experience reloading the little round, I do have a bit of experience reloading 50BMG and even a few rounds of .510DTC.
                          NRA Certified Pistol, Rifle, Shotgun and Metallic Cartridge Reloading Instructor
                          California DOJ Certified Fingerprint Roller
                          Ventura County approved CCW Instructor
                          Utah CCW Instructor


                          Offering low cost multi state CCW, private basic shooting and reloading classes for calgunners.

                          sigpic
                          CCW SAFE MEMBERSHIPS HERE

                          KM6WLV

                          Comment

                          • #14
                            mjmagee67
                            Veteran Member
                            • Jun 2011
                            • 2771

                            Originally posted by Scar13
                            The die set I am using is made by Lee Precision. I took another look at my setup and see that the bullet seating die does not come in contact with the bottom die at all, there is probably 3/8" between the two fully possitioned to seat the bullet. I know when I size the brass (Once fired Barrett brass) I make sure that I do a cam over, but have never really concentrated on this in the bullet seating. Are they suppose to touch?
                            I measured the bullets and see that the neck size is .413. These are solid brass bullets.
                            Thx
                            Shouldn't a 416 be .416? I would say the bullets are machined too small.
                            If you want change you have to put in your 2 cents, you can't just sit on the sidelines and whine.

                            Comment

                            • #15
                              mrkubota
                              Senior Member
                              • Oct 2005
                              • 1372

                              Originally posted by Scar13
                              I will look at these diffeent suggestions you guys have given me. I have also received some suggestions from the techs at Lee. I will let you know what I find out.
                              I reload .416 and am in the Redlands/Yucaipa area if you want any help.
                              Should be back in CA after Christmas.

                              //Ben
                              06FFL - Custom Ammunition

                              Comment

                              Working...
                              UA-8071174-1