Unconfigured Ad Widget

Collapse

Another .223 question... Am I doing something wrong?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Prophet
    Member
    • Apr 2010
    • 200

    Another .223 question... Am I doing something wrong?

    About two years ago I started reloading straight walled pistol case. I am new to reloading rifle and I need some assistance. .223 is what I will be reloading. The dies that I am using are RCBS 2-die set.

    1) Do I need to trim every time after resizing? Or does the case only need to be under the max case length of 1.760"?

    2) In the Hornady reloading book that I have it shows the mouth OD as .253". After resizing the mouth OD is .245". I have the die set down where it touches the shell holder and the decapper protrudes 3/16" past the bottom of the die. Do I need to set the die so when resized the mouth is .253"? I pushed a bullet into one of the resized (.245") cases and it when in smooth. Am I doing some thing wrong?

    3) I will mainly be shooting using semi-auto rifle. Do I need to crimp?

    As always, all advice is greatly appreciated.

    -P
    Last edited by Prophet; 12-12-2012, 12:20 PM.
  • #2
    nimbus
    Senior Member
    • Nov 2009
    • 674

    1) Just trim if the cases are over 1.760. No need to trim every time.
    2) Not sure about this one. Do you have a drop in case gauge? That's what i use to see if I resized my brass properly.
    3) Some say to crimp, some will say not to crimp...really up to you. I personally crimp my plinking rounds (just a bit) where my bullet has a cannelure. I do not crimp precision loads though.

    Comment

    • #3
      BSlacker
      Senior Member
      • Dec 2003
      • 923

      I pushed a bullet into one of the resized (.245") cases and it when in smooth.
      If this was done with fingers only then the neck is too loose, if the bullet was seated on the press it might be ok. Start by measuring the neck ID and compare that too bullet OD. The case neck OD has the variable of neck brass thickness and doesn't compare case maker to maker. Give the completed round a firm push against a solid bench top. You should be able to put some force on it.
      Get a drop in case gauge. It will tell you if your loaded rounds will most likely chamber correctly and be safe to shoot. Your quality will go up.
      Some folks crimp some don't. It depends on your experience with your firearm. Bolt shooters have few problems not crimping, it seems that crimp issues rears their ugly head in semi auto firearms. Its not that much more to crimp.

      Comment

      • #4
        Prophet
        Member
        • Apr 2010
        • 200

        Thanks for the help. I do not yet have a case length gauge- is the any other way to check for case length other than placing the round in the chamber?

        Comment

        • #5
          Irish_Man
          Junior Member
          • Jun 2012
          • 16

          Use a caliper, go get one from Harbor freight or Home depot for cheap.. I like the drop in case length gauges (LE Wilson). Way fast to check a bunch of brass for trimming..

          Make sure when you reload that you are reloading the same type of brass (ie. All Federal or PMC or whatever). It will make you reloads and seating depth more consistent.

          Also for like $12 you can get a Lee Factory Taper Crimp die, and set it to just barely crimp the round. Don't use the RCBS Seater/Crimp die to do this as I have had problems with it setting the shoulder back on the round. I put a little touch of crimp on all my plinking rounds for AR-15. You do not want the bullet to set back as it's pushed up the ramps into the chamber..

          Comment

          Working...
          UA-8071174-1