Unconfigured Ad Widget

Collapse

Chamfer and Deburring Station

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 23's Dad
    Senior Member
    • Jun 2010
    • 502

    Chamfer and Deburring Station

    I'm just getting into reloading for rifles. I started using my chamfer/deburr tool and I was sick of the task within 20 rounds. I wanted to set up a powered station to perform the task but I was concerned about a couple of issues.

    Technical:
    1) over chamfering at high speeds, and sharpening the case mouth excessively or even shortening it beyond the trimmed length.
    2) Running the tool at speeds higher than designed and reducing tool life and heating the brass
    3) Sticking my non-replaceable digits into the region of a spinning metal object.

    Price/convenience:
    1) I don't have a lot of room for a permanent install,
    2) I don't want to dedicate my only battery powered drill to the task, or buy a dedicated tool for the job.
    3) Noise

    I realized I already had the perfect tool in my box. An old manual crank drill! It has an adequately sized chuck to fit my deburring/chamfer tool. The tool runs at low speed. I already own it. And I can control the cut by counting the rotations of the handle.

    Tah Dah!!!:





    It chamfers, deburrs, it even makes potato chips.

    Anyway it has certainly reduced the agony of the task, and is really speedy. I can chamfer, swap ends, and deburr a hundred trimmed cases in about 15 minuets.
    Last edited by 23's Dad; 12-03-2012, 12:27 PM. Reason: fix typo
  • #2
    slo5oh
    Senior Member
    • May 2005
    • 730

    I wonder if i could convert my mothers old foot pedal sewing machine like this...

    Comment

    • #3
      Quinc
      Veteran Member
      • Jan 2010
      • 3011

      my next purchase will trim and debur at the same time:
      Forster Products’ 3-in-1 Case Mouth Cutter is the first carbide case trimmer accessory that performs three functions simultaneously. In one simple step, this product: • Trims the case to length • Chamfers the inside case mouth to an angle of 14° • Chamfers the outside case mouth to an angle of 30° To further save you t
      Shop Amazon and contribute to CGF!
      click this link before going to amazon.com
      http://www.shop42a.com

      sigpic
      www.appleseedinfo.org

      "Everyone has a plan, till they get punched in the face." -Mike Tyson

      Comment

      • #4
        shooterbill
        Senior Member
        • Feb 2012
        • 1096

        Cool idea. I never thought of using a manual drill. I have the Lyman case prep express and it works great. The drill would have been a cheaper way to go.

        Comment

        • #5
          Wombat25
          Member
          • Nov 2008
          • 348

          My cordless drill has a flat-bottom battery that allows it to stand on my workbench. I put my chamfer/deburr tool in a drill adapter, throw it in there, and use a zip-tie to hold the trigger down at a moderate speed. This has worked great for me for years now.

          Comment

          • #6
            23's Dad
            Senior Member
            • Jun 2010
            • 502

            Looked into that too...

            Originally posted by Quinc
            my next purchase will trim and debur at the same time:
            http://www.grafs.com/retail/catalog/...roductId/20891

            I don't like the Forester Trimmer that I have, so I didn't want to put more cash down that hole.

            I bought a WFT and love it. http://www.littlecrowgunworks.com/wft.html

            It cuts the cases really square, but leaves a sharp edge on the case mouth to chamfer and deburr.

            Comment

            Working...
            UA-8071174-1