Unconfigured Ad Widget

Collapse

OFFICAL 458 Socom reloading thread!

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Quinc
    Veteran Member
    • Jan 2010
    • 3011

    OFFICAL 458 Socom reloading thread!

    Finally bought an RRA CAR upper and now I need some loads! So I thought I would start thread. I am going to post all the info I have saved off other forums and hopefully we can get some 458 Socom reloaders here.

    Use loads at your own risk!! I have not personally used these yet!

    Barnes 600 gr RN

    bullet is 1.600" long
    RE7 22gr
    OAL with the 600 gr RN is 2.255


    525gr pile driver with gas check. 540gr total

    RE-7 24.6gr
    CCI 350 Primer
    OAL 2.085
    Very light crimp (LEE FCD)

    Velocity:
    1. 1079 fps
    2. 1074 fps

    Avg. 1076 fps

    Notes: Recoil NOT harsh, good hard “push”.


    RE-7 26.0 grs.
    CCI 350 Primer
    OAL 2.085
    Very light crimp (LEE FCD)

    Velocity:
    1. 1140 fps
    2. 1142 fps
    3. 1151 fps

    Avg. 1144 fps

    Notes: Noticeably “sharp” recoil impulse compared to lighter load.

    So far the most accurate load is...

    IMR4198 25.2gr
    CCI 350
    No crimp
    OAL=2.125


    BERRY 350 GR COPPER PLATED BULLET

    LIL GUN
    28grs
    OAL 2.085 MAX

    H110
    29gr
    OAL 2.085
    SHOT GROUP 3 INCHES AT 50 YRDS

    IMR 4198
    34grs.
    OAL 2.085.
    SHOT GROUP 1-2 INCHES AT 50 YRDS





    Last edited by Quinc; 08-04-2012, 11:26 PM.
    Shop Amazon and contribute to CGF!
    click this link before going to amazon.com
    http://www.shop42a.com

    sigpic
    www.appleseedinfo.org

    "Everyone has a plan, till they get punched in the face." -Mike Tyson
  • #2
    Quinc
    Veteran Member
    • Jan 2010
    • 3011



    (Note: Many are near maximum loads, you should use 10% less to start.)
    (See note on Powders below or read all about various Powders.)
    Bullet is .458" diameter. Due to different barrel lengths, type of bullet, seating depth, primer type and other factors, you may not get near the FPS charted. It is just a guide and the reason you should start under these charges and work up.

    ----------------------------------------
    300 Barnes X
    Lil'Gun 32.8 gr. 1,886
    ----------------------------------------
    300 Remington JHP
    Lil'Gun 29.5 gr. 1,745
    Lil'Gun 30.5 gr. 1,788
    Lil'Gun 32.0 gr. 1,854
    Lil'Gun 34.6 gr. 1,985 (very hot load)
    H-110 34.8 gr. 1,645
    W-296 33.5 gr. 1,772
    H-4198 40.2 gr. 1,756
    ----------------------------------------
    325 Hornady FTX
    IMR-4198 38.6 gr. 1,593
    H-4198 38.8 gr. 1,604
    Lil'Gun (use between 28.5 gr. and 30.0 gr. for ~1,700-1,800 fps category)
    ----------------------------------------
    (note: Matt's Bullets makes a 365 Grain Lead, Round Flat Nose + Gas Check (.458)
    that should be experimented with if the flat nose does not create a feed problem)
    ----------------------------------------
    405 Remington JFP
    Lil'Gun 28.9 gr. 1,594
    H-110 34.4 gr. 1,657
    HS-6 14.5 gr. 1,086 (quiet with a suppressor)
    W-296 32.5 gr. 1,585
    ----------------------------------------
    420 Lead Cast RNFP + Gas Check
    Lil'Gun 28.0 gr. 1,602
    Lil'Gun 28.8 gr. 1,635
    ----------------------------------------
    500 Hornady RN
    IMR-4198 26.4 gr. 1,066
    -----------------------------------------

    Discussion: * Most magnum pistol powders can be used as well as some rifle powders. The somewhat faster pistol powders are preferable for the lighter 300 grain range bullets, while slower burning powders work better with the heavy weights. However, case capacity can become an issue with bulky rifle powders. If I can find some loads with 2400, that might be a good experiment.

    Hodgdon's Powder Guide on line and other internet sources. There is still a lot of experimenting with loads and blogs as of 2012 are the best source. You can back off loads. They may not work the action of the upper rifle, but you can work up in .2 grain increments to find what is best.
    Shop Amazon and contribute to CGF!
    click this link before going to amazon.com
    http://www.shop42a.com

    sigpic
    www.appleseedinfo.org

    "Everyone has a plan, till they get punched in the face." -Mike Tyson

    Comment

    • #3
      rromeo
      Calguns Addict
      • Sep 2009
      • 6981

      Thanks. I don't have a thumper yet, but after looking at the Beowulf, Bushmaster, and SOCOM, I keep leaning towards SOCOM.
      Never initiate force against another. That should be the underlying principle of your life. But should someone do violence to you, retaliate without hesitation, without reservation, without quarter, until you are sure that he will never wish to harm - or never be capable of harming - you or yours again.

      - from THE SECOND BOOK OF KYFHO
      (Revised Eastern Sect Edition)

      Comment

      • #4
        Noah
        Member
        • Apr 2008
        • 272

        I have a barrel on order from wilson combat. Also some brass and dies on the way. So I am glad to see this thread start. I will definitely post up once I get some loads made and tested.
        Noah
        Also anyone who has ordered the lee fc die.. I was wondering if it matters what bullet the dummy has seated in it? What exactly is lee looking at when you send them the dummy? If it just the trim length of the brass? Anything else?
        http://www.a-human-right.com/

        For 15 things YOU CAN DO to improve our 2nd A RKBA so we can: pass "Shall Issue" Right-to-Carry; repeal the CA AWB; and pass a CA con. RKBA amendment, go to: http://www.calguns.net/calgunforum/s...416#post842416

        CA-NRA: http://www.calnra.com/

        Comment

        • #5
          Quinc
          Veteran Member
          • Jan 2010
          • 3011

          Best deal on bullets I can find are the Berrys 350gr platted and the 405gr gas checked. I am still trying to find some load data for the 405gr gas checked.

          Anyone have any tips/info on coming up with your own load data. Starting powder / OAL etc?
          Shop Amazon and contribute to CGF!
          click this link before going to amazon.com
          http://www.shop42a.com

          sigpic
          www.appleseedinfo.org

          "Everyone has a plan, till they get punched in the face." -Mike Tyson

          Comment

          • #6
            Quinc
            Veteran Member
            • Jan 2010
            • 3011

            405gr Remmy bullets
            Shop Amazon and contribute to CGF!
            click this link before going to amazon.com
            http://www.shop42a.com

            sigpic
            www.appleseedinfo.org

            "Everyone has a plan, till they get punched in the face." -Mike Tyson

            Comment

            • #7
              Rusty Scabbard
              Senior Member
              • Dec 2010
              • 591

              Just got started

              Reloaded SBR brass cases this weekend.
              WLP primers
              300 gr Sierra JHP
              30 gr Lil' Gun
              Then tried another batch with 31.2 gr Lil' Gun

              All expended cases looked OK, but I had a bit of trouble getting consistent seating and correct OAL, especially with the first batch. Seating too deep definitely increases pressures. Worst case was one with 30 gr Lil' Gun, with OAL 1.994. Primer was flat but the case looked OK.
              Groups were marginal (about 4"), I assume largely due to the different seating depths.

              A few questions for the pro's and gurus here:
              I'm using Redding dies. I couldn't get consistent seat depths. (+/-0.020") Can you get different seating inserts for the dies ? Am I better off with different projectiles ? The soft lead of the exposed JHP tips may have imperfections or diameter variation.

              I could see a definite firing pin imprint after rounds were chambered. Are CCI350's harder than WLP ? Anyone have a favorite primer recommendation for this round ?

              Is there a bullet puller that works with the reduced base dia. of this round ? Mine can't grip them.

              Thanks in advance for any help !

              Comment

              • #8
                Noah
                Member
                • Apr 2008
                • 272

                Originally posted by Rusty Scabbard
                Is there a bullet puller that works with the reduced base dia. of this round ? Mine can't grip them.
                I know others have taken a dremel to the one side of the little pie pieces that grab the rim, opened them up where the case is hitting and made it work. I am not sure if there is a puller that works out of the box but would like to know as well.

                Noah

                P.S. I am not sure if you are already aware, but I understand that if you are seeing pressure signs like the flatened primers then you have exceeded the max pressure of the .458 socom.

                Warning for any who are unaware:
                The .458 socom is designed to be a relatively low pressure and has some unique issues when hand loading.
                I was totally unaware of this until I really started searching out load data online, and came across several experianced .458s guys urging caution.
                A couple of quotes that stuck out to me.
                When reading pressure signs the job is easy. You DON'T. The SOCOM uses large pistol primers. The maximum pressure for the .458 S as well as the Beowulf is 35K. By the time you see any pressure signs you are WAY over the 35K psi limit. Stick to established data. Forget the notion that you can load until you see the primers flatten and then back off a little. That will still put you about 8,000 psi over the maximum pressures allowable.
                AND
                On a serious note, for ANYBODY reloading for the 458S: ANY Pressure Signs means your in dangerous territory and back off!
                http://www.a-human-right.com/

                For 15 things YOU CAN DO to improve our 2nd A RKBA so we can: pass "Shall Issue" Right-to-Carry; repeal the CA AWB; and pass a CA con. RKBA amendment, go to: http://www.calguns.net/calgunforum/s...416#post842416

                CA-NRA: http://www.calnra.com/

                Comment

                • #9
                  Quinc
                  Veteran Member
                  • Jan 2010
                  • 3011

                  I keep reading that the 458S shoots up to 600gr bullets. Anyone have a source for 600gr bullets? I cant find any.
                  Shop Amazon and contribute to CGF!
                  click this link before going to amazon.com
                  http://www.shop42a.com

                  sigpic
                  www.appleseedinfo.org

                  "Everyone has a plan, till they get punched in the face." -Mike Tyson

                  Comment

                  • #10
                    Noah
                    Member
                    • Apr 2008
                    • 272

                    Barnes made a 600gr in the barnes "Original"... however I do not see it listed on their webpage, possibly it has been discontinued. MidwayUSA has a few 550s.
                    I haven't seen any 600s on the sites I buy components from.
                    I would think a hard cast 600 should be available somewhere but I don't see any when I search.
                    Noah
                    http://www.a-human-right.com/

                    For 15 things YOU CAN DO to improve our 2nd A RKBA so we can: pass "Shall Issue" Right-to-Carry; repeal the CA AWB; and pass a CA con. RKBA amendment, go to: http://www.calguns.net/calgunforum/s...416#post842416

                    CA-NRA: http://www.calnra.com/

                    Comment

                    • #11
                      Quinc
                      Veteran Member
                      • Jan 2010
                      • 3011

                      What do you guys think about cast bullets? Gas checks or no? I am thinking about giving the LAsercast bullets a try.

                      As always, your satisfaction GUARANTEED or you money back
                      No leading
                      Slick Silver Bearing Alloy yields highest velocities of all Extreme accuracy
                      Shop Amazon and contribute to CGF!
                      click this link before going to amazon.com
                      http://www.shop42a.com

                      sigpic
                      www.appleseedinfo.org

                      "Everyone has a plan, till they get punched in the face." -Mike Tyson

                      Comment

                      • #12
                        Noah
                        Member
                        • Apr 2008
                        • 272

                        Their 405gr looks like a winner for larger game(butte county bears). Their prices look great too if their special alloy lives up to the hardness claims and lack of leading. Thanks for the link, I plan on putting plenty of lead through mine.
                        Are there any special issues/considerations with the .459 diameter?
                        http://www.a-human-right.com/

                        For 15 things YOU CAN DO to improve our 2nd A RKBA so we can: pass "Shall Issue" Right-to-Carry; repeal the CA AWB; and pass a CA con. RKBA amendment, go to: http://www.calguns.net/calgunforum/s...416#post842416

                        CA-NRA: http://www.calnra.com/

                        Comment

                        • #13
                          Quinc
                          Veteran Member
                          • Jan 2010
                          • 3011

                          Originally posted by Noah
                          Their 405gr looks like a winner for larger game(butte county bears). Their prices look great too if their special alloy lives up to the hardness claims and lack of leading. Thanks for the link, I plan on putting plenty of lead through mine.
                          Are there any special issues/considerations with the .459 diameter?
                          Everything I have been reading say to go with .459 in RRA uppers and .458 with Marty's uppers.

                          Speaking of bears we have them getting in our trash constantly...
                          Shop Amazon and contribute to CGF!
                          click this link before going to amazon.com
                          http://www.shop42a.com

                          sigpic
                          www.appleseedinfo.org

                          "Everyone has a plan, till they get punched in the face." -Mike Tyson

                          Comment

                          • #14
                            Noah
                            Member
                            • Apr 2008
                            • 272

                            Quinc,
                            Can you expand on what you know about .458 vs .459. I need to put in a call to Wilson Combat and find out how closely their specs are to a Marty barrel vs a RRA. Do you know where the differences are? Is it just in the chamber, or the bore, or both? I would really like to give those 405s a try but don't want any issues. I am guessing they will fire through a Marty barrel just at the risk of bumping up to higher/unsafe pressures?

                            Noah

                            P.S. Sorry to hear about your bear trouble, It has been a bad year for that with the poor snow pack. Luckily we are low enough in elevation that we don't see them around our place... have had a few incidents from our friendly neighborhood mountian lion though.
                            http://www.a-human-right.com/

                            For 15 things YOU CAN DO to improve our 2nd A RKBA so we can: pass "Shall Issue" Right-to-Carry; repeal the CA AWB; and pass a CA con. RKBA amendment, go to: http://www.calguns.net/calgunforum/s...416#post842416

                            CA-NRA: http://www.calnra.com/

                            Comment

                            • #15
                              Quinc
                              Veteran Member
                              • Jan 2010
                              • 3011

                              I've read on a couple different forums about the teppo uppers being cut tighter at exactly .458 and the RRA uppers being at .459. I will post more info if I come across the threads again.
                              Shop Amazon and contribute to CGF!
                              click this link before going to amazon.com
                              http://www.shop42a.com

                              sigpic
                              www.appleseedinfo.org

                              "Everyone has a plan, till they get punched in the face." -Mike Tyson

                              Comment

                              Working...
                              UA-8071174-1