Unconfigured Ad Widget

Collapse

When to trim?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Banana_hands
    Member
    • Dec 2011
    • 484

    When to trim?

    I'm in the research stage of reloading (specifically .223 and 9mm) but i'm a bit confused. If you have to trim rifle cases you're supposed to do it after resizing correct? But if that's the case, how/when do you trim when using a progressive press? Most setups I've seen de-cap and resize at the first station then go on to complete the round. So when are you supposed to trim?
  • #2
    Bill Steele
    Calguns Addict
    • Sep 2010
    • 5028

    Originally posted by Banana_hands
    I'm in the research stage of reloading (specifically .223 and 9mm) but i'm a bit confused. If you have to trim rifle cases you're supposed to do it after resizing correct? But if that's the case, how/when do you trim when using a progressive press? Most setups I've seen de-cap and resize at the first station then go on to complete the round. So when are you supposed to trim?
    I load rifle on a single stage for the exact conundrum you point out. Some guys that have a Dillon 650 use a Dillon Power Trimmer on the second station when loading in high volume for rifle (like .223).

    I have a four station progressive, don't shoot enough rifle to justify the big bucks for the above setup, so I just use my single stage for my rifle rounds and use my progressive for handgun.
    When asked what qualities he most valued in his generals, Napoleon said, "give me lucky ones."

    Comment

    • #3
      morrow
      Member
      • Dec 2011
      • 377

      You trim ANY brass you want after resizing.
      Generally you only need to trim rifle (necked) brass
      Some poeple trim revolver brass to get a more consistant roll crimp
      There's some straight wall brass like 30carbine you need to trim just like rifle brass.

      When using a progressive press take all of your fired brass AFTER you tumble it and lube it, and run it through the machine using ONLY the sizing/depriming die. Once that entire batch is sized/deprimed you can trim it.

      Then you run the trimmed/chamfered/deburred brass through the machine again and prime, powder, and seat the bullet. Done!

      Personally right before I trim the brass I use calipers and check for maximum OAL, if it's under, and the case mouth isn't nicked up, I don't bother trimming it.

      Comment

      • #4
        bigdawg86
        Veteran Member
        • Mar 2012
        • 3554

        So how does does everybody assure that your brass that you pick up is only yours so you don't have to measure EVERY casing before reloading? I just trimmed 1000+ 223 rounds and if I shoot with buddies, our brass ends up on the floor together. It's great cause they don't reload and I get to keep their once fired brass, but... How do you guys keep your already prepped brass/reloads separate from the rest of the once fired factory load everyone else shoots?

        Comment

        • #5
          morrow
          Member
          • Dec 2011
          • 377

          Originally posted by bigdawg86
          So how does does everybody assure that your brass that you pick up is only yours so you don't have to measure EVERY casing before reloading? I just trimmed 1000+ 223 rounds and if I shoot with buddies, our brass ends up on the floor together. It's great cause they don't reload and I get to keep their once fired brass, but... How do you guys keep your already prepped brass/reloads separate from the rest of the once fired factory load everyone else shoots?
          That's the hard part. Some poeple separate headstamps. I just check the OAL of brass after I size/deprime it, then trim if needed. Checking brass OAL goes really fast, just set your calipers to the maximum OAL or slightly under and see if the brass slides through (after you size/deprime it)

          Comment

          • #6
            bigdawg86
            Veteran Member
            • Mar 2012
            • 3554

            Do those "brass catchers" work? Or is that a dork accessory?

            Comment

            • #7
              killshot44
              Veteran Member
              • Nov 2009
              • 4072

              Mark your case heads with a Sharpie. It comes off when you tumble 'em.

              The Action Pistol guys do this all the time to keep their brass separate.

              Comment

              • #8
                Banana_hands
                Member
                • Dec 2011
                • 484

                Thanks for all the responses. I'll probably end up doing a Morrow suggests and run the brass through just to decap and resize then again to load.

                Morrow, I'm in SD as well, have you been over to la mesa collectibles (I think that's the name)? If so, how are there prices on powder and primers? I'm looking to avoid the hazmat shipping fees while supporting a local business.
                Thanks,
                Khris

                Comment

                • #9
                  XDRoX
                  Veteran Member
                  • Mar 2009
                  • 4420

                  Brass catchers work great.

                  If you trim 9mm you need to see a shrink and get some medication for that.

                  Trimming 223 is way overrated. Trim it once and shoot it until it cracks. If you're OCD then trim is once and use an X-die to resize and shoot it until it cracks.
                  Chris
                  <----Rimfire Addict


                  Originally posted by Oceanbob
                  Get a DILLON...

                  Comment

                  • #10
                    XDRoX
                    Veteran Member
                    • Mar 2009
                    • 4420

                    Originally posted by Banana_hands
                    Thanks for all the responses. I'll probably end up doing a Morrow suggests and run the brass through just to decap and resize then again to load.

                    Morrow, I'm in SD as well, have you been over to la mesa collectibles (I think that's the name)? If so, how are there prices on powder and primers? I'm looking to avoid the hazmat shipping fees while supporting a local business.
                    Thanks,
                    Khris
                    Their prices are OK. They can't compete with Internet prices though. If you want a pound of something then they're OK. I usually order in large volume and just use the Internet.
                    Chris
                    <----Rimfire Addict


                    Originally posted by Oceanbob
                    Get a DILLON...

                    Comment

                    • #11
                      Banana_hands
                      Member
                      • Dec 2011
                      • 484

                      Thanks XDRoX for your response. I might swing by there just to see what they have to offer. Any recommendations on powder for 9mm? Im assuming from your avatar and your name that you shoot 9mm, possibly an XD9. That's what I shoot and an XD9 service model.

                      Comment

                      • #12
                        morrow
                        Member
                        • Dec 2011
                        • 377

                        Originally posted by XDRoX
                        Brass catchers work great.

                        If you trim 9mm you need to see a shrink and get some medication for that.

                        Trimming 223 is way overrated. Trim it once and shoot it until it cracks. If you're OCD then trim is once and use an X-die to resize and shoot it until it cracks.
                        +1 for that, actually, +2 for that.
                        Good advice. I've never trimmed 9mm or 45acp.

                        Comment

                        • #13
                          morrow
                          Member
                          • Dec 2011
                          • 377

                          Originally posted by Banana_hands
                          Thanks XDRoX for your response. I might swing by there just to see what they have to offer. Any recommendations on powder for 9mm? Im assuming from your avatar and your name that you shoot 9mm, possibly an XD9. That's what I shoot and an XD9 service model.
                          For 9mm I like HP38/W231. There are several good powders that work for 9mm though.

                          Comment

                          • #14
                            Banana_hands
                            Member
                            • Dec 2011
                            • 484

                            Thanks, any preference in small pistol primers? I was planning on CCI #500 small pistol primers but midwayusa is out of stock, I'll have to shop elswhere.

                            Comment

                            • #15
                              morrow
                              Member
                              • Dec 2011
                              • 377

                              Originally posted by Banana_hands
                              Thanks, any preference in small pistol primers? I was planning on CCI #500 small pistol primers but midwayusa is out of stock, I'll have to shop elswhere.
                              I just use the cheapest Wolf/TULA primers. They work fine for me. There are a lot of good primer brands out there though.

                              If you're going to buy primers and/or powder online anyway and pay the hazmat fee, try looking at http://www.powdervalleyinc.com/ they usually have the best prices.

                              Comment

                              Working...
                              UA-8071174-1