Unconfigured Ad Widget

Collapse

Ladder test and max load

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Hunt
    Veteran Member
    • Sep 2009
    • 4836

    Ladder test and max load

    I have finally found the time to do a couple of ladder test to see if I can find the sweet spot with a couple of different bullets. I am shooting the 7mm-08 and tried the speer 130 gr BTSP and the speer 145 gr BTSP. In both case it seems the sweet spot is near the published max loads RL17 absolutely no pressure signs at published max loads. I get the impression I could easily exceed the published max by a grain or two but won't do that as good practice demands staying with published loads. However the way the test looks I would benefit by refining the loads to within .5 gr over max. Anyone ever try loads over published max?
    Protect public lands access http://www.backcountryhunters.org/
  • #2
    NotEnufGarage
    CGN/CGSSA Contributor
    CGN Contributor
    • Oct 2010
    • 4832

    I have, but only for 6.8MM Remington SPC. Almost all published loads are for the original SPC chamber (which was incorrectly implemented because of a misread of the drawings) and my barrel has the SPC-II chamber (correct implementation), which can handle higher pressures. This was only done at the suggestion of a long-time SPC-II shooter and loader and I was very careful working past max load data. I saw no signs of overpressure on my spent cartridges and only went ~1 grain above max.

    If you do this, work up very slowly (.1 - .2 grain at a time) and check cases and primers carefully against a few reference cases fired at low pressure, in good light with a magnifier. Once you get to the ragged edge, you don't have to go far to have problems.

    I'm sure that for liability reasons the powder manufacturers published max loads are a bit below the true max pressure limits of the gun/chamber to allow for slight variations in powder consistency. Still, be very, very careful and take all safety precautions possible (eyes, ears, head).
    sigpic
    NRA Life Member (Benefactor level)

    "Those who give up some of their liberty in order to obtain a little temporary safety, deserve neither liberty, nor safety." B. Franklin
    Calguns Community Chapters (C3) in Your Community
    Calguns Community Chapters (C3) and Appleseed Event Calendar

    The 2nd Amendment is not about hunting or competition shooting. It's all about your inalienable rights to life and liberty.

    Comment

    • #3
      Ahhnother8
      Senior Member
      • Feb 2007
      • 1454

      Originally posted by Hunt
      Anyone ever try loads over published max?
      Yes, all the time. Many factors determine the max load in any given firearm. And the more the throat wears, the higher the max gets. FWIW, I have gone as high as 10% over max.

      Comment

      • #4
        Hunt
        Veteran Member
        • Sep 2009
        • 4836

        I figure the published loads have lawyer specs on them, all I want to try is maybe 0.1 increments up to at max 0.5 over, otherwise comon sense dictates to back off due to numerous variations that could effect pressures. yes I do use a magnifier and good light when checking brass. Notenufgarage Can you describe the "ragged edge" you are talking about?
        Protect public lands access http://www.backcountryhunters.org/

        Comment

        • #5
          NotEnufGarage
          CGN/CGSSA Contributor
          CGN Contributor
          • Oct 2010
          • 4832

          "Ragged Edge" would be slight primer deformation, case bulging, etc.. Going past that point will eventually end up with a kaboom.

          When I was testing my 6.8 loads at nearly 10% over published, I thought for sure I'd see some signs, but I didn't see a thing. I might go a little hotter, just to give me a chance to see pressure signs for myself, other than just in pictures on the web.

          0.5 grain over published loads for 7MM-08 is barely 1%. I would bet there's 5% to 10% safety built into published loads, so you could go farther. I guess it's all a matter of how tight a sphincter you're comfortable with.
          sigpic
          NRA Life Member (Benefactor level)

          "Those who give up some of their liberty in order to obtain a little temporary safety, deserve neither liberty, nor safety." B. Franklin
          Calguns Community Chapters (C3) in Your Community
          Calguns Community Chapters (C3) and Appleseed Event Calendar

          The 2nd Amendment is not about hunting or competition shooting. It's all about your inalienable rights to life and liberty.

          Comment

          • #6
            Hunt
            Veteran Member
            • Sep 2009
            • 4836

            ^^^^yeah thanks, this is coming together for me
            Protect public lands access http://www.backcountryhunters.org/

            Comment

            • #7
              MONGO3006
              Junior Member
              • Apr 2007
              • 92

              Hunt if you go to snipers hide in the reloading forum there is a section on this that could and will give you some great information on this subject. I have not done it yet but plan to when I can get the time to do this.

              Comment

              Working...
              UA-8071174-1