Unconfigured Ad Widget

Collapse

Ring around the V-Max

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Trigger Guard
    CGN/CGSSA Contributor - Lifetime
    CGN Contributor - Lifetime
    • Jul 2009
    • 191

    Ring around the V-Max

    Hello all,

    Having trouble getting my .224 V-Max boolets seated without the stupid sharp edged RCBS Comp seater impressing a ring at the contact point. I'm reluctant to relieving the inside edge as there is not much material there to remove and I don't have a lathe.

    Anyone else encountered this and, is there a replacement part available for this die hidden somewhere in deep dark cyberspace? If so, could you please direct me.

    There has been no problem with other projectiles using the same die, me thinks the V-Max is hollow under that thin shell of copper.

    Thanks
  • #2
    kmullins
    Senior Member
    • Aug 2009
    • 942

    Try wrapping a undersized bore mop in some 0000 steel wool with some Flitz metal polish and chuck it in a cordless drill. Then run it in the bullet seater (be careful not to hit it with the metal wire inside the bore mop). It won't take off any material, but will even out any burs or sharp edges.

    Also, you can take out the bullet seating plug and chuck it into a cordless drill and use the Flitz/0000 steel wool to polish the edge.

    Good luck!

    Comment

    • #3
      grant22
      Senior Member
      • Aug 2011
      • 625

      I've had the same thing with Dillon carbide and Hornady 75 gr Match.
      Reloaders: Stay safe, even the things you don't see may bite you. Read more here: http://www.calguns.net/calgunforum/s...d.php?t=495909

      Comment

      • #4
        RugerNo1
        Senior Member
        • Jul 2008
        • 1644

        Reduce neck tension, polish the seating stem, or use a bullet with a thicker jacket.
        Dane

        For the Learned Rifleman

        Comment

        • #5
          Trigger Guard
          CGN/CGSSA Contributor - Lifetime
          CGN Contributor - Lifetime
          • Jul 2009
          • 191

          Is mere polishing enough? It would seem that it needs a taper to create more surface area at the contact point.

          Comment

          • #6
            Fjold
            I need a LIFE!!
            • Oct 2005
            • 23094

            Just spin the seating stem in an electric drill and hold some rolled up emery paper (400 grit) against the inner edge.
            Frank

            One rifle, one planet, Holland's 375




            Life Member NRA, CRPA and SAF

            Comment

            • #7
              Coyotegunner
              Senior Member
              • Jan 2011
              • 1353

              I use them in 204,223,22-250.Yea I get the little ring around the top(RCBS DIES).The bullets are made to explode when they hit a animal.I also get it in Nosler Accubonds for the 300RUM and 375H&H.I think the dies are pretty generic for different types of bullets.Maybe I am wrong,but I have not had complaints from anything.Hope we are talking about that little impression at the top below the plastic tip.

              Comment

              • #8
                Coyotegunner
                Senior Member
                • Jan 2011
                • 1353

                Forgot to say.I will not fool around with my dies.RCBS is great about taking care of them.They really encourage people not to modify them.

                Comment

                • #9
                  Shoot-it
                  Calguns Addict
                  • Dec 2005
                  • 5165

                  do you debur the inside of the neck?I never had a problem loading them for the 223 and 243.
                  Originally Posted by olhunter View Post
                  I prefer to not mount the fat ones.
                  Nice racks are much better. You can grab both sides of the rack to help stabilize while mounting.
                  ProShooter's
                  You'd never guess that human beings are apex predators reading some of the weepy vaginas in this thread, it's a moose people, who cares.

                  Comment

                  • #10
                    Coyotegunner
                    Senior Member
                    • Jan 2011
                    • 1353

                    I loaded some Nosler Accubonds last night for the 375 H&H.I have a slight depression in the bullet from the seater die.Hornady dies.Like Shoot it suggested,I always deburr.Makes me wonder if all of these plastic tipped bullets are soft with the copper.I have not seen it in Hornady or Sierra with the lead tips.Is the ring a sharp cut or smooth type depression.

                    Comment

                    • #11
                      Trigger Guard
                      CGN/CGSSA Contributor - Lifetime
                      CGN Contributor - Lifetime
                      • Jul 2009
                      • 191

                      I checked my .308 comp die and found that the seating stem rests further down the bullet and below the oglive. I think I am going to see if RCBS will sell me stems only for some other calibers that may fit better on the various shapes and sizes.

                      Comment

                      • #12
                        Trigger Guard
                        CGN/CGSSA Contributor - Lifetime
                        CGN Contributor - Lifetime
                        • Jul 2009
                        • 191

                        Originally posted by Shoot-it
                        do you debur the inside of the neck?I never had a problem loading them for the 223 and 243.
                        Are you using a standard seater die? I only have a comp die for .223 and don't know what the stem looks like or fits like for standard tooling.

                        De bur the case? Yes... RCBS Trim Mate. The problem seems to be only with V-Max bullets as I have loaded 1000s of Speer, Nolser, Barnes etc. with no visible damage caused by the seater stem.

                        Comment

                        • #13
                          G-forceJunkie
                          Calguns Addict
                          • Jul 2010
                          • 6530

                          I've seen this when there is too much neck tension. Is the brass new? If so, did you run an expander ball down it and if so what size? If used brass, Neck sized down to what size?

                          Comment

                          • #14
                            Shoot-it
                            Calguns Addict
                            • Dec 2005
                            • 5165

                            Originally posted by Trigger Guard
                            Are you using a standard seater die? I only have a comp die for .223 and don't know what the stem looks like or fits like for standard tooling.

                            De bur the case? Yes... RCBS Trim Mate. The problem seems to be only with V-Max bullets as I have loaded 1000s of Speer, Nolser, Barnes etc. with no visible damage caused by the seater stem.
                            Yes just the standard seater from Lee.The brass I use is at least onced fired.
                            Can you post a picture of that ring?
                            Originally Posted by olhunter View Post
                            I prefer to not mount the fat ones.
                            Nice racks are much better. You can grab both sides of the rack to help stabilize while mounting.
                            ProShooter's
                            You'd never guess that human beings are apex predators reading some of the weepy vaginas in this thread, it's a moose people, who cares.

                            Comment

                            • #15
                              NRAhighpowershooter
                              Super Moderator
                              CGN Contributor - Lifetime
                              • Jun 2003
                              • 6485

                              i ran a thread about the same thing back in 2/2010 and I called RCBS and they told me they would cut a seating stem for my competition seating die.. cost $10 I think...i sent them a bullet along with a letter what I wanted done (also mention that you want the bullet back!)
                              'Just Don't Point, Squint, and Laugh! '

                              Distinguished Rifleman Badge #2220

                              Comment

                              Working...
                              UA-8071174-1